HaierメーカーHWD-D1200TXVEの使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANUAL Automatic Drum W ashing Machine HWD-D1200TXVE HWD-D1200TXVEME HWD-D1000TXVE HWD-D1000TXVEME.
page no. Before use Parts .......................................................................................................... 1 Safety instructions ................................................................................. 2 - 4 Installation .
1 This diagram may vary slightly with the layout of the washing machine you have just purchased due to technical improvements. NOTICE Please read these instructions carefully before using this appliance.
2 Using your appliance will be simple, but please make sure read the following to get the best out of it and to ensure your own safety . BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME: DO ✓ Ensure you connect the appliance directly to a domestic mains water supply .
3 DURING DAIL Y USE OF THE APPLIANCE DO ✓ Unplug the appliance before carrying out any maintenance or repair . ✓ Hold the plug and not the electric cable when unplugging the washing machine. ✓ Keep the door slightly open when not in use to prevent formation of odours.
4 Electrical connection (UK ONL Y) For your safety please read the following information W arning: This appliance must be earthed. The appliance must be connected to a 220 volt 240 cycle AC supply by means of a three pin socket, suitably earthed and should be protected by a 13 amp fuse.
Caution: protective gloves should be warn • Remove all the packing materials (including the foam base) to prevent vibration during use, as show in Fig.
6 Connecting the hose to the cold water supply 1. Connect the nut on the water inlet hose to the connector on the water valve. Ensure all seals are in place. 2. Tighten the nut to secure the hose. Drain hose • The height of the drainage outlet must be between 80-100cm.
7 C o n t r o l p a n e l A. Po w er bu tt on G . St ar t/ Pau se b ut to n B . Pro g r am m e selec t io n d ial H . b ut to n C . D et er g en t d istr ib ut io n dr a w er I. D r y b ut to n D . S p in spe ed sett in g b ut to n J . Ex t ra r in se b ut to n E.
8 G. Start/Pause button When the washing machine is connected to the power socket and a programme is selected, touch this button to start operation. T ouch this button again during operation to pause the programme. The display screen will flash and the machine will be paused.
9 Programme selection guide NOTE: “O” indicates that softener can be added if need; “ ★ ” indicates that detergent must be added; “X” indicates that detergent must not added; “*” indicates cold water . 1) The wash temperature indicates the maximum temperature.
10 Preparing for a cycle Detergent selection Only special low foam detergent should be used in automatic drum washing machines. For blended or wool fabrics, special detergent should be used. Dry cleaning solvent should not be used. Caution: do not use too much detergent.
1. Loading Open the door , put in the laundry piece by piece and then tightly close the door . Notes: 1) Before the first run of the appliance it is advisable to run the machine empty on a quick wash with no detergent to clean through the system. 2) Do not overload the washing machine.
12 3. Selecting washing programme T o get the best wash, an appropriate washing programme should be selected according to the type of laundry . 4. W ashing temperature settings Set the washing temperature as required, otherwise set at position * when a cold wash is acceptable.
1. Control panel lock function: T o prevent children from accidentally changing the settings, the control panel can be locked by pressing the “T emperature” and “Delay” buttons at the same time. After the panel is locked, the sign “LOCK” and the remaining wash time will be displayed on the LED alternately .
14 1. T urn off the water tap and pull out electricity plug after each wash. Open the porthole to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace the drain hose.
5. T o prevent blockage to the water supply by ingress of foreign substances, clean the water inlet and inlet filter regularly . 6. If the machine is to be moved to a distant place, replace the vibration absorbing locks (packing screws, rubber gaskets) removed before installation to prevent damage as shown below .
16 T rouble shooting In the unlikely event of difficulties with your appliance please follow the trouble shooting guide below . If the problem persists, contact an approved service engineer . If an error code is displayed, please refer to the error code guide below .
1 7 M o d el / I tem H W D - D 1 0 0 0 T X V E/ M E H W D -D 1 2 0 0 T X V E/ M E Po w er So u rc e 2 2 0 - 2 4 0 V / 5 0 H z 2 2 0 - 2 4 0 V / 5 0 H z W o rkin g C ur ren t ( M a x ) ( A) 1 0 1 0 Tap W a ter Pr essur e ( M Pa) 0 .
W e apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product improvement and development. The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
デバイスHaier HWD-D1200TXVEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Haier HWD-D1200TXVEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHaier HWD-D1200TXVEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Haier HWD-D1200TXVEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Haier HWD-D1200TXVEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Haier HWD-D1200TXVEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHaier HWD-D1200TXVEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Haier HWD-D1200TXVEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHaier HWD-D1200TXVEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
