HaierメーカーHWM90-0713Sの使用説明書/サービス説明書
ページ先へ移動 of 18
User's manual This manual is for HWM90-0713S Please read this manual carefully before using. Retain it for future reference. T win-tub Washing Machine 0030807907C.
Contents Names of the parts - - - - - - - - - - - - - - - - - 1 Safety precautions - - - - - - - - - - - - - - - - - 2 Installation and adjustment - - - - - - - - - - - 4 Preparation before washing - .
1 Meaning and description of the symbols Warning sign Forbidding sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents, otherwise it may cause damage of the machine or injure the personal safety of the user .
Safety precautions Please insert the power cord into special receptacle with rated vol- tage. Be sure to use single-phase three pins receptacle. The earthing terminal of the receptacle must be earthed reliably. If possible, please adopt electric leakage protector.
Please don t use the washer in the environment below 0 C. If the washer is below 0 C, the washer s water inlet system and draining system will be frozen ,then result in the damaged of the whole machine. If the washer has below 0 C, please be sure to ensure the washer is placed under the room temperature for 2~4 hours and then use .
Installa tion and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package, please take out the lint filter from the document bag, install it to the overflow filter of the wash tub.
5 How to change the direction of the drain hoses Install the water inlet hose; Select the water level Insert the water inlet hose into the water-filling entrance on the control pane directly.(pull it out to dismantle it) Select water level according to the quantity of the laundries.
Pr epar a tion bef or e washing 6 Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe.
The musts in washing 7 The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.
Washing sequence 8 Figure 3 Spin timer Was h timer (T o set to below 2 minute, first set to 6 minute then turn it back. it can increase the service life of the timer). (to set to below 1 minute, first set to 2 minute then turn it back. it can increase the service life of the timer).
9 Rinse with stored water Rinse with water-filling 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is a few , please use "Standard" current.
T o do spinning and draining together, please first do spinning for around 1 minute, then do draining . Otherwise the spinning will stop owing to too much water stored in the spin tub. In spinning, it will pause the work if you open the outer cover of the spin tub.
11 After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. 1 T ake off the overflow filter.
12 Cleaning the overflow filter 2. T ake off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1). 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water.
13 Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty. Do not wash it directly by water. After washing, dismount the water inlet hose. Do not store water in the tub for long period. Discharge the water immediately after each using.
14 T ro uble-shooting Answ er to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
15 W ater inlet hose Gland Lint filter Packing list Twin-tub washing machine Name Quantity User's manual One piece One piece One piece One piece One set.
16 Specification W ater level/Water quantity (L) (about) Maximum/48 Medium/39 Minimum/33 Injection pressure(MPa ) 0.02 0.2 Wa shing capacity(kg) 6.0 Spinning capacity(kg) 4.
デバイスHaier HWM90-0713Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Haier HWM90-0713Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHaier HWM90-0713Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Haier HWM90-0713Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Haier HWM90-0713Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Haier HWM90-0713Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHaier HWM90-0713Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Haier HWM90-0713Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHaier HWM90-0713Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
