HaierメーカーHWMP65-918の使用説明書/サービス説明書
ページ先へ移動 of 20
Automatic Washing Machine User manual This manual is for HWMP55-918 HWMP65-918 Please read this manual carefully before using. Retain for future reference.
CONTENTS 1 Safety Precautions 2-3 Installation and A djustment 4 Installation 5 Installation water inlet hose 6 Before washing 7 Detergent 9-13 4 T rouble-shooting 15 Packing list 17 Specifications 18.
Drain connector Inner tub Detergent box T op lid Balance ring Lint filter (HWMP55-918) Pulsator Cabinet Adjustable leg Fixed leg Back cover 1 Pr oduct Ove r view Contents marked with this symbol are related to the safe use of the product and the personal safety of the user .
Saf ety Prec autions The ventilation holes at the bottom Soft object Back Front A separate, earthed power socket is required for the power supply. Hold the plug - NOT the electric cable - when unplugging the washing machine. Do not insert or remove the power plug with wet hands.
Safety precautions 3 Do not leave hot or heavy items on lid or control panel as this may cause damage to the washer or make the washer unsafe to operate Do not attempt to move washing or place hands inside washing machine while in operation. Please ensure children are supervised around machine to avoid harm.
Install the bottom plate 4 Please install and adjust the machine according to the directions contained in this manual. It is very important to follow these directions for the safe operation of the machine, and to ensure your machine operates correctly .
5 Installa tion of d ra ina ge hose Install draina ge hose First connect the drainage hose to the connection point on the lower left side of the cabinet, and fasten with drain hose hoop (provided). Connect drain hose guide on to the outside of drainage hose.
6 1. Insert a new flat washer into each end of the inlet hose. 2. Connect the water inlet hose to the water faucet. You may have to use pliers to tighten the coupling.
7 Bef or e washing Preparation 1. Ensure the water inlet hoses are correctly installed and faucets are turned on. 2. Insert the power plug into the electrical socket. 3. Ensure the drain hose is mounted at the correct height. 4. Select a suitable location for the washer on a hard, even Surface, away from direct sunlight or heat sources, e.
Load the laundry The rated washing capacity refers to the largest dry weight of a load that can be washed. The thickness, size and type of clothes will influence the actual capacity . Do not select more than W ater Level 4 for clothes less than 1.0kg, to avoid splashing of water.
Operation & Wash Cyc les 9 G F E D C B A Long Medium Rapid Express Indicator display On Indicates the program is about to run and indicates the selected cycle and options Flashing Indicates the pr.
C Delay button B Wash Rinse Spin button The display shows the time remaining (in minutes) before the cycle will finish. Push the "Delay" button and the display will show the remaining time for the cycle to finish (in hours). The indicator flashes to indicate that the delay function is operating.
11 Button Operation and Descriptions 1 2 Cycle When the power is switched on "Normal" cycle is automatically set. T o select a different automatic cycle, press the "Cycle" button till the corresponding indicator is on. Refer to the section on the "Cycle" button above.
12 3 Wash Rinse Spin For the "Synthetic"and "Memory" cycles the machine will run a Fuzzy Logic program that automatically detects the type of laundry in the tub.
Ãê 7 Press the button to start the cycle If the top lid is opened while machine is in SPIN cycle, the machine will stop and an audible alarm will sound. ˜Ñ Cycle completed The energy test program was performed using the "Normal" cycle default setting of: Wash "Long" Rinse:1 Rinse Spin:7 mins Water level:10.
Remove and clean the detergent box, replace after cleaning. The lint filter must be used during washing. It must be cleaned after each use Lint filter: 1. Slide upwards to remove. 2. Gently push it down to install; ensuring it is in place before next wash.
15 T r ouble-shooting If there is a fault or the machine does not operate correctly, remove the power plug before checking the machine. Using diagnostic list below, please check the machine requires repair. If a repair is required, please contact our Customer Care T eam, do not try to fix it yourself.
There maybe water in the drain hose in when first used. It maybe residual water after performance inspection by the factory . Common occurrences Situation Cause The spinning is intermittent after it starts. The wash procedure pauses. Select spin program, but it does not work.
Packing list 17 Automatic washing machine Between the upper cushion of the washing machine package and the upper seal of the package carton. Bottom plate Inside Accessory b ag One T ap ping screws Use.
Specifica tions Model Rated voltage/frequency Rated washing power Rated spinning power Net weight Gross weight Dimensions (mm) HWMP55-918 220-240V 50Hz 380W 340W About 32.
デバイスHaier HWMP65-918の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Haier HWMP65-918をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHaier HWMP65-918の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Haier HWMP65-918の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Haier HWMP65-918で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Haier HWMP65-918を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHaier HWMP65-918の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Haier HWMP65-918に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHaier HWMP65-918デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。