American DynamicsメーカーADCC0200の使用説明書/サービス説明書
ページ先へ移動 of 56
ControlCenter TM ADCC0200 ADCC0300 Keyboard Installation and Operation Instructions 8200-0855-05 A0.
ii ADCC0200 and ADCC0300 Notice The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products.
iii Keyboard Installation and Operation TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SER VICEABLE P AR TS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE T O RAIN OR MOISTURE.
iv ADCC0200 and ADCC0300 PPOUR RÉDUIRE LES RISQUES D’ÉLECTROCUTION, NE P AS DÉPOSER LE COUVERCLE. AUCUN COMPOSANT NE PEUT ÊTRE RÉP ARÉ P AR L ’UTILISA TEUR.
v Keyboard Installation and Operation UM STROMSCHLÄGE ZU VERMEIDEN, DARF DIE ABDECKUNG NICHT ENTFERNT WERDEN. DAS GERÄT ENTHÄL T KEINE DURCH DEN ANWENDER W ARTBAREN TEILE. W ARTUNGSARBEITEN DÜRFEN NUR VON QUALIFIZIERTEM W ARTUNGSPERSONAL DURCHGEFÜHRT WERDEN.
vi ADCC0200 and ADCC0300 A TTENZIONE : Si tratta di un prodotto di classe A. In un ambiente domestico il prodotto può causare interferenze radio nel cui caso potrebbe essere richiesto all’utente di adottare misure adeguate. Emissioni in radiofrequenza Regolamento della Federal Communications Commission (FCC) Parte 15.
vii Keyboard Installation and Operation PRECAUCIÓN : Este es un producto de Clase A. En entornos domésticos, este producto puede provocar interferencias de radio, en cuyo caso es posible que el usuario deba adoptar las medidas correctoras oportunas.
viii ADCC0200 and ADCC0300 LET OP : Dit is een A-klasse product. In woonomgevingen kan dit product tot radiostoring leiden en dient de gebruiker passende maatregelen te nemen. Radiofrequentie-emissie Federale voorschriften van de Federale communicatiecommisie (Federal Communications Commission Code of federal regulations), deel 15.
1 Keyboard Installation and Operation CHAPTER 1: ABOUT THE ADCC0200 AND ADCC0300 KEYBOARD .................................................. 3 Key Features ...............................................................................................
2 ADCC0200 and ADCC0300 CHAPTER 4: PROGRAMMING WITH THE ADCC0200/ADCC0300 KEYBOARDS ............................ 28 Entering Program Mode (RS232 only) ............................................................................................. .2 8 Exiting Program Mode (RS232 only) .
3 Keyboard Installation and Operation Chapter 1: About the ADCC0200 and ADCC0300 Keyboard This chapter describes the features of the ADCC0200/ADCC0300 keyboard.
4 ADCC0200 and ADCC0300 ADCC0200 and ADCC0300 Keyboard Overview The keyboard consists of the following element s: 1. Clear key - clears any numerical data entered during camera, monitor selection etc. Used to backstep or exit the menu system. 2. Menu key - used to enter the matrix menu system.
5 Keyboard Installation and Operation 1 1. Numeric keypad - keys ranging from 0 to 9 that enable the user to select specific cameras, monitors, presets, sequences, etc. 12. Monitor key - selects the monitor whose number was entered on the numeric keypad.
6 ADCC0200 and ADCC0300 33. Auxiliary key - toggles auxiliary between ON state and OFF state (if function is available). 34. Flip key - automatically turns the selected dome through 180 O . 35. Auxiliary 2 key - toggles auxiliary 2 between ON state and OFF state.
7 Keyboard Installation and Operation Feature Quick Reference The features that are available depend on the keyboard in use (ADCC0200 or ADCC0300) and the communication format that is utilized (RS232 or RS485).
8 ADCC0200 and ADCC0300 St andard Matrix Operations (continued) Matrix Menu Operations FEA TURE KEYBOARD COMMAND ADCC0200 ADCC0300 RS485 RS232 RS485 RS232 Run T our T our number → Hold .
9 Keyboard Installation and Operation Dome Operations FEA TURE KEYBOARD COMMAND ADCC0200 ADCC0300 RS485 RS232 RS485 RS232 Enter Dome Menu Mode → AND Exit Dome Menu Mode Via Dome Menu .
10 ADCC0200 and ADCC0300 VCR (PIP) / Direct Control Mode (All Functions A vailable in Direct Control Mode) FEA TURE KEYBOARD COMMAND ADCC0200 ADCC0300 RS485 RS232 RS485 RS232 Select VCR Mode RS232 : V.
11 Keyboard Installation and Operation Chapter 2: Connection and Setup This chapter describes the power and data connections between the ADCC0200/ ADCC0300 keyboard and the switching system being used. IMPORT ANT NOTE The default setting for the keyboard is RS485 mode at 19200 baud.
12 ADCC0200 and ADCC0300 Installation Precautions This installation should only be carried out by qualified personnel, and should conform to all local electrical codes.
13 Keyboard Installation and Operation Connections for Cable Distance of Seven Feet or Less (RS232 Mode) For installations where the keyboard-to-system cable dist ance is seven feet or less, connect the cables in accordance with the figures below . The RJ-45 socket on the MP-KMI that is marked Matrix is connected to the switching system.
14 ADCC0200 and ADCC0300 Multiple Keyboards on an RS485 Network A maximum of 16 devices may be connected when working in RS485 mode. A maximum of eight keyboards can be assigned to the system. For correct connection of multiple keyboards to an MegaPower L T , please see the MegaPower L T Installation and Operation Handbook.
15 Keyboard Installation and Operation Multiple Keyboards on an RS232 Network Use the following diagram as guidance to connect multiple RS232 keyboards via a port expander . The following rules must be observed: 1. A maximum of four RS232 keyboards can be connected to the network.
16 ADCC0200 and ADCC0300 Chapter 3: Basic Operations - Operate Mode (ADCC0200 and ADCC0300) This chapter describes basic keyboard operations such as calling cameras to view on monitors, running tours, p atterns, presets, macros and salvos.
17 Keyboard Installation and Operation Keyboard Display The 16 character , two-line LCD keyboard display shows site, monitor , and camera numbers, as well as various status messages and numerical data entered by the user . The main functional areas of the LCD display are shown below .
18 ADCC0200 and ADCC0300 The selected video input will now appear on the monitor screen. After calling a camera to the selected monitor , any other camera can be called to the monitor by repeating the two steps above.
19 Keyboard Installation and Operation Controlling Camera Focus Focus refers to the action of adjusting the clarity of the camera image displayed on the monitor . T o focus the camera on a distant object, press the F AR key . T o focus on a closer object, press the NEAR key .
20 ADCC0200 and ADCC0300 Auto Focus Certain cameras are designed with Auto Focus capability . The feature can be enabled from the keyboard as follows. T o enable auto focus: 1. Hold down the FUNCTION ( ) key . 2. Press either the FOCUS NEAR/FOCUS F AR or OPEN IRIS/CLOSE IRIS keys.
21 Keyboard Installation and Operation Running Patterns A pattern is a series of p an, tilt, zoom, and focus commands defined for a dome camera. A pattern is programmed in real time, which means that the dome remembers each pattern segment in the actual time it t akes the operator to execute a command.
22 ADCC0200 and ADCC0300 Running T ours A tour is a dynamic sequence of camera views, each of which appears on a selected monitor screen for a specified dwell time , and each of which can have a pre-programmed preset status, auxiliary status, and connect next status.
23 Keyboard Installation and Operation Reversing a T our When a tour is running, the NEXT ( ) and LAST ( ) keys can be used to reverse the direction of a tour . T o reverse the direction of a tour: 1. Press the LAST ( ) key once. Note, to again reverse the tour , press the NEXT ( ) key once.
24 ADCC0200 and ADCC0300 Calling Views (RS485 only) A view is the simultaneous display of a specific preset position on a specific camera. T o call a view: 1. Enter the view number using the numeric keys. The number entered will appear on the right hand side of the top line of the LCD display .
25 Keyboard Installation and Operation Setting the Keyboard Display Contrast 1. Press the FUNCTION ( ) and MENU ( ) key . 2. Use the Focus NEAR/Focus F AR key to increase/decrease the display's contrast. 3. When the contrast is satisfactory , press the ENTER key .
26 ADCC0200 and ADCC0300 Operating a VCR or Digit al Recorder T o initiate VCR control, the operator performs the following actions: 1. Enter the number of the VCR/DVR using the numeric keys. 2. Press the VCR SELECT ( ) key . The VCR/DVR number will be shown in the top line of the display in the format R nnnn.
27 Keyboard Installation and Operation T elemetry Enable/Disable (RS485 only) T o send telemetry commands to cameras, it is necessary to enable telemetry to the selected camera. The telemetry key has a toggle action. T o enable/disable telemetry: 1. Press the TELEMETRY ( ) key .
28 ADCC0200 and ADCC0300 Chapter 4: Programming with the ADCC0200/ADCC0300 Keyboards This chapter provides step-by-step instructions for programming the keyboard.
29 Keyboard Installation and Operation Matrix Menu The keyboard is able to view the main menu of the switching matrix system being used. T o enter matrix menu mode: 1. Hold down the SHIFT ( ) key and press the MENU ( ) key . This will open the main menu for the switching matrix system on the currently selected monitor .
30 ADCC0200 and ADCC0300 Dome Menu Functions The ADCC0300 keyboard can be used to configure a suitable dome camera by remotely accessing the dome camera's menu system T o enter the dome camera menu: 1. Call the dome camera to the monitor . 2. Press the FUNCTION ( ) key .
31 Keyboard Installation and Operation T o exit a dome camera menu: 1. Use the joystick to select QUIT WITHOUT SA VING - this will exit the dome menu without saving any changes. 2. Use the joystick to select EXIT AND SA VE CHANGES - this will save any changes and exit the dome menu.
32 ADCC0200 and ADCC0300 Clearing Patterns (RS485 only) If a dome supports the clear p attern feature, then this operation will delete the programmed pattern. T o clear a pattern: 1. Press the FUNCTION ( ) key . 2. Enter the pattern number using the numeric keys.
33 Keyboard Installation and Operation Chapter 5: Installer Functions This chapter provides step-by-step instructions for keyboard installer functions.
34 ADCC0200 and ADCC0300 Setting the Network Timeout Period 1. Enter the S pecial Config menu. 2. Press the VCR SELECT ( ) key . 3. At the "RS485 T imeout" prompt, enter the period required. The number entered is in units of 5mS e.g. entering 10 will set the timeout period to 50mS.
35 Keyboard Installation and Operation Disabling/Enabling the Sounder 1. Enter the S pecial Config menu. 2. Press the VCR F AST FOR WARD ( ) key . 3. At the "Sound 1=On 2=Off" prompt, enter 1, or 2 and then press the ENTER key . Selecting RS485 or RS232 mode 1.
36 ADCC0200 and ADCC0300 Setting the Passcode (Program Lock) Function IMPORT ANT - to set the passcode, the keyboard must be in RS232 mode. 1. Enter the S pecial Config menu. 2. Press the MENU ( ) key . 3. At the "Program Keylock Enter to Enable" prompt, press the ENTER key .
37 Keyboard Installation and Operation Appendix A: ADCC0200/ADCC0300 VCR Reprogramming The ability to reprogram the RS232 commands, that are sent out when the unit is in RS485 mode with Direct Control enabled, has been added.
38 ADCC0200 and ADCC0300 The following text should initially be shown on the teminal: PLA 02 46 50 4C 03 REV 02 52 50 4C 03 PAU 02 50 41 55 03 REW 02 52 45 57 03 FWD 02 46 57 44 03 REC 02 52 45 43 03 .
39 Keyboard Installation and Operation Appendix B: Monitor Arming Commands Monitors are armed for alarm call up with codes that specify the following three parameters: 1. The display method ( single , dual , or block monitors). 2. The queuing method ( sequence or hold ).
40 ADCC0200 and ADCC0300 Appendix C: T roubleshooting Problem ✗ No power to keyboard ✗ No response to keystrokes (power verified) ✗ Keyboard responds to keystrokes on some, but not all keys ✗ .
41 Keyboard Installation and Operation Appendix D: Specifications Model Numbers ADCC0200 .................. Keyboard with two-axis joystick ADCC0300 .................. Keyboard with three-axis joystick MP-CBL ....................... S pare cable MP-KMI .
42 ADCC0200 and ADCC0300 Index A Alarms 24 Auto Focus 20 Auto Iris 19 Auto Repeat Mode 35 Auxiliaries 24 B Baud Rate 34 Biasing the Network 14 C Calling a Camera to View on a Monitor 17 Calling Preset.
43 Keyboard Installation and Operation Function T ables DirectSet Feature 10 Dome Operations 9 Matrix Menu Operations 8 S tandard Matrix Operations 7 VCP (PIP) / Direct Control Mode 10 H Holding T our.
44 ADCC0200 and ADCC0300 Program Mode Entering 28 Exiting 28 Locking 28 Setting the Passcode 36 Programming Dome Patterns 31 R Resetting to Factory Defaults 35 Restarting a Held T our 22 Reversing T o.
45 Keyboard Installation and Operation.
46 ADCC0200 and ADCC0300.
47 Keyboard Installation and Operation.
48 ADCC0200 and ADCC0300 Please visit our website for more information ww w .americandynamics.net © 2006 American Dynamics Product specifications subject to change without notice Certain product name.
デバイスAmerican Dynamics ADCC0200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
American Dynamics ADCC0200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAmerican Dynamics ADCC0200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。American Dynamics ADCC0200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。American Dynamics ADCC0200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
American Dynamics ADCC0200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAmerican Dynamics ADCC0200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、American Dynamics ADCC0200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAmerican Dynamics ADCC0200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。