HaierメーカーXQB70-10の使用説明書/サービス説明書
ページ先へ移動 of 20
Names of the parts.............the 2 nd cover Safety precautions .......................1 Introduction of the special functions.........3 Installation and adjustment ..................3 Install the water inlet hose............5 Preparation before washing .
Meaning and description of the symbols Honourable users, Thank you for choosing our products. Our products integrate high-tech, precision,frontier science.T o facilitate using it, please read this manual carefully and operate this machine according to it.
Before Using Before Using Saf ety pr ecautions Please insert the power cord into special rece- ptacle with rated voltage.If the power cord is three-phase wire,please use three-phase rec- eptacle.The earthing terminal of the receptacle must be earthed reliably .
Do not decompose, repair or alter the machine by yourself. Do not put any hot or heavy items (such as the kettle with hot water ) on the washing machine. Do not wash laundries with volatile materials (such as thinner, petrol etc.) The handicapped or children without care shall not use the machine.
The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will result in unstable running or stoppage of the machine.
1. The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way . 2. Do not trample or press the drain hose. If the drain hose is too long, cut it at mid point. T o make smooth drainage, cut the front end of the hose slantingly .
Water tap,suitable Water tap,not suitable It is required that the front end shall be longer than 10mm. The outlet end surface of the tap shall be flat and smooth. If not please file it to avoid leakage. 2. Loosen the screw till the water tap can be accessed.
1.Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged before each usage. If it happens please contact our after-sale department immediately . 2.Put the nut of the water inlet hose on the valve jointer. 3.Fasten the nut.
Confirm if there's special requirment for the laundries. Clear the pocket. T ake out the coins , sand, hairpins etc. Fasten the buttons and zippers. When the pulsator is running , the buttons of the laundries may cause noise. For the sake of discretion,please put the laundries with buttons into other laundries.
Reference weight of the laundries: working suit up,down jeans about 800g The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. One time washing quantity shall be lower than the rated capacity.
How to use the whitener Fill water to decided level. Dilute the whitener with container . Pour it slowly into the washing tub. Avoid using whitener on laundries with color or pattern as they are prone to lose color . The whitener shall not touch the laundries directly .
The user selects a suitable water level depending on the load. If "Quick" wash is selected, water level will indicate "2". After water level reaches "2", it will wash while water filling, and wash normally upon the water level reaching "4".
Remarks: After pressing "Power On/Off" to connect power supply , if the washing machine lasts idle more than 10 min, it would automatically shut off the supply . XQB70-10 T o indicate -- during sensing. T o indicate remaining min. During program running.
WA TER LEVEL SELECTION RESERV ATION PROCEDURE SELECTION POWER ST ART ON / OFF PROGRAM SELECTION NORMAL BIG CLOTHING GENTLE QUICK WASH After the power is switched on, the washing machine will automatically set a normal program comprising of processes of "Wash, Rinse and Spin" .
Even there's no water in the tub, the spinning will start after a certain period. Do not use soak process for woolen laundries . Wash the laundries that are prone to lose colors separately from other laundries. The pulsator will not rotate unless the water is filled to selected water level.
After switching on, the washing machine reserved wash program will be automatically set inactive. If you desire a wash cycle to end at a reserved time, you can press the " Reservation " button to set a reserved wash program. Refer to " The button of Reservation " on page 11.
After switching on, the washing machine reserved wash program will be automatically set inactive. If you desire a wash cycle to end at a reserved time, you can press the " Reservation " button to set a reserved wash program. Refer to " The button of Reservation " on page 11.
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company .
User's manual Name Components of the water inlet hose Bottom plate T apping screws ST4x16 One One One Eight One Quantity Inside the document bag Storage position Automatic washing machine Inside .
Rated voltage frequency Rated washing / spinning capacity W ater level/Water quantity (about) Max water consumption pressure Rated washing power Rated spinning power Weight Dimension 7.0kg (weight of standard dry cloth) About 1 26L (High water l evel; Standard program) 0.
デバイスHaier XQB70-10の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Haier XQB70-10をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHaier XQB70-10の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Haier XQB70-10の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Haier XQB70-10で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Haier XQB70-10を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHaier XQB70-10の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Haier XQB70-10に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHaier XQB70-10デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。