Hamilton ElectronicsメーカーAM1000の使用説明書/サービス説明書
ページ先へ移動 of 18
AM1000 INSTALLATION INSTRUCTIONS OUTSIDE TRANSMITTER AM1000 213 CARAWAY LN Cary NC 27519 1.
.
Get Started! Pick three locations 1) a place for the transmitter 2) place for your studio or inside connection (can just be under a des k) and 3) a ground.
Now mount the transmitter to the m ast using the bracket (see bracket instructio ns). If you are not using a bracket, install transmitter to wall or acceptable confi guration. Install 102” Ante nna (Radio Shack # 21-903) to the transm itter, it screws into the t op.
Please note that changes or modifications not expressly approved by RangeMaster for compliance could void the user's authority to operate the equipment. Installing the AM1000 transmitter This unit is meant to be installed by someone who has some radio background.
3 your wire is to large to fit into the bi nding po st use a short section of wire and a wi re nut to complete the connection. Weatherproof the wire nut connecti on. It is important to keep the ground wire away from metal on the way to ground rod to get good range and provide the best lightning protection.
4 Step 4 If things look good so far take the tuning tool and rotate “TUNE” to obtai n a peak reading of the meter. When the meter peaks you are tuned. Be sure to stay away from the antenna while tuning. If you are to close to the antenna your body will affect where it tunes.
5 Now go and check your range. Use your car and your odometer to check the range. Do the final tune on “TUNE” (Check t o be sure the meter voltage is still peaked ). Adjust “AUDIO LEVEL” control for best sound on your radio. Keeping the antenna as verti cal as possible will help your range.
POWER ADJUST AM1000T Module (if installed ) COIL TUNE Audio Level CRYSTAL CAP TUNE TEST HOLES 6.
.
AM1000T Power Set / Tuning Module Power Adjust LED J13 Coil Tune Cap Tune When transmitter is turned on, the com puter will start in Power Set mode if th ere is a shunt in J1 3 (Power is set last). When you are tuning you will get better readings with the power all the way down (Power Adjust counter clockwise).
To go to the Cap Tune program just leave the shunt in J 13 for 15 seconds, the LED will turn off. Take the shun t off j13 (and then replace shunt onto J13) and you are in the Cap Tune program. To find the peak voltage using this program you need to ge t used to working with the program .
If you are using an Innovonics 222 be sure your output polarity is correct, here is how: 1. Turn the positive peaks all the way down 2. Turn the output level up until you get distortion, then back off a little (hair) for good sound.
.
COPY FEDERAL CO MMUNICATION S COMMISSION WASHINGTON, D. C. 20554 GRANT OF EQUIPMENT AUTHORIZATION COPY Certification Hamilton PCB Design 134 Wind Chime Ct.
.
.
1.0 1.00 1.1 .910 1.2 .840 1.3 .770 1.4 .720 1.5 .670 1.6 .630 1.7 .590 1.8 .560 1.9 .530 2.0 .500 2.1 .480 2.2 .455 2.3 .435 2.4 .420 2.5 .400 2.6 .385 2.7 .370 2.8 .360 2.9 .345 3.0 .335 3.1 .325 3.2 .315 3.3 .305 3.4 .295 3.5 .285 3.6 .280 3.7 .270 3.
デバイスHamilton Electronics AM1000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hamilton Electronics AM1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHamilton Electronics AM1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hamilton Electronics AM1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hamilton Electronics AM1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hamilton Electronics AM1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHamilton Electronics AM1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hamilton Electronics AM1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHamilton Electronics AM1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。