American PanelメーカーAP20BC175-2の使用説明書/サービス説明書
ページ先へ移動 of 38
R E V . C Cooler is Better! TM USER’S MANUAL BLAST CHILLER / SHOCK FREEZER MODEL AP20BC175-2 American Panel Corporation 5800 S.E. 78th Street, Ocala, Florida 34472-3412 Phone: (352) 245-7055 Fax: (352) 245-0726 E-mail: service@americanpanel.
AP20BC175-2 Manual 1 INDEX INTRODUCTION 3 CONTROLLER FEATU RES 3 OPERATING MODES 3 AUTOMATIC MODE 3 MANUAL MODE 3 OPERATING CYCLES 4 ADDITIONAL CYCLES 4 PRINTER 4 PC CONNECTION (OPTIONAL) 4 INSTALLATI.
AP20BC175-2 Manual 2 MANUAL SOFT CYCLE PARAME TERS PROGRAMMING 20 MANUAL HARD CYCLE PARAMETERS PROGRA MMIN G 21 3. RECIPE NAME PROGRAMMING 22 OPERATION 23 1. AUTOMATIC MODE - SOFT CHILL 23 2. MANUAL MODE - SOFT CHILL 24 3. HARD CHILL CYCLE 25 4. DEFROST CYCLE 25 5.
AP20BC175-2 Manual 3 INTRODUCTION Blast Chiller Model AP20BC175-2 is used to rapidly chill cooked foods to temperatures suitable f or refrigerated storage. It is capable of lowering the core temperature of up to 200 pounds of most foods from 160 o F to 40 o F in 90 minutes.
AP20BC175-2 Manual 4 OPERATING CYCLES The operator can choose from the following 3 operating cycles: MODE END FOOD TEMP. USES NOTES SOFT CHILL 38 o F TO 40 o F FOR LOW DENSITY FOODS AIR TEMP. IS 28 o F TO 35 o F HARD CHILL 38 o F TO 40 o F FOR MEDIUM & HIGH DENSITY FOODS AIR TEMP.
AP20BC175-2 Manual 5 INSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURI NG INSTALLATION (8 STEPS) COMPRESSOR FIG. 1 1. Inclination of the piping. FIG. 2 2. Fastening of brackets on insulated piping. FIG. 3 3. Airtight welding. FIG. 4 4. Create the vacuum and load the line.
AP20BC175-2 Manual 6 INSTALLATION AT DIFFERENT LEVELS If the remote condensing unit is installed at a higher level than the cabinet (FIG. 6) insert a siph on in the return line at every 6 ft. of difference in height. If the remote condensing unit is installed at a lower level than the cabinet (FIG.
AP20BC175-2 Manual 7 INSTALLATION WARNINGS READ ALL OF THE INSTRUCTIO NS IN THIS MANUAL BEFOR E YOU ATTEMPT TO INSTALL THE EQUIPMENT AND CAREFULLY FOLLOW THEM. ALWAYS DISCONNECT THE UNIT FROM THE POWER SOURCE B EFORE PERFORMIN G ANY SERVICE OR MAINTENANCE .
AP20BC175-2 Manual 8 4. At least 15” clear space is required above the unit for service. 5. At least 6” is required on both sides of the cabinet (for servicing the control panel an d door opening).
AP20BC175-2 Manual 9 SPACES AROUND THE CABINET • At least 15" clear space is required above the unit for service. • At least 6" clear space is required on both sides of the cabinet. • At least 6" clear space is required on the rear of the cabinet for drain hookup and maintenance.
AP20BC175-2 Manual 10 USING THE HURRICHILL™ TECHNOLOGY BLAST CHILLING All cooked food rapidly loses its quality and aroma if it is not served promptly. Natural bacteria growth, the main reason why food becomes stale, takes place at an exponential rate between 140°F and 40°F.
AP20BC175-2 Manual 11 PANNING AND LOADING PANNING 1. Standard pan depth is 2-1/2”. Other depths can be used but are not recommended as their use would require an increase in the cycle time. 2. Stainless steel or aluminum pans are recommended, as plastic containers will increase the chilling time.
AP20BC175-2 Manual 12 CONTROL PANEL FOR MODEL AP20BC175-2 BLAST CHILLER.
AP20BC175-2 Manual 13 KEYBOARD KEYS ON/OFF & START/STOP CYCLE KEYS ON/OFF SOFT CYCLE START/STOP HARD CYCLE SHOCK CYCLE PROGRAMMING KEYS AUTOMATIC CYCLE UP MANUAL CYCLE DOWN UV LIGHT CYCLE SELECT D.
AP20BC175-2 Manual 14 PR OGRAMMING 1. INITIAL PROGRAMMING NOTE: Initial programming is preset at the factory. Use this section only if changes are desired. If no changes are to be made, skip to Page 17 ( 2. Programming the cycles ). a. With the display reading "OFF" , press ("START/STOP") for a few seconds.
AP20BC175-2 Manual 15 g. To set the day, press or then press . 03(day) Blinks h. To set the hour, press or (be sure to continue to press the buttons until the hour and " AM" or " PM" show correctly) then press . 10(hours) Blinks i.
AP20BC175-2 Manual 16 p. To change t o YES or NO , press or then press . NO Blinks q. To change t o YES or NO , press or then press . NO Blinks r. To change to YES or NO , press or then press . YES Blinks s. To change to YES or NO , press or then press .
AP20BC175-2 Manual 17 y. To change to YES or NO , press or then press . NO Blinks z. To change to YES or NO , press or then press . NO Blinks aa. To change to YES or NO , press or then press . NO Blinks The display will show for 2 seconds: Then the controller will go into “OFF” state.
AP20BC175-2 Manual 18 d. To change the temperature, press or then press . 28 Blinks e. To change the temperature, press or then press . 35 Blinks f. To change the temperature, press or then press . 40 Blinks g. To change the temperature, press or then press .
AP20BC175-2 Manual 19 l. To change the temperature, press or then press . 60 Blinks m. To change the temperature, press or then press . 28 Blinks n. To change the temperature, press or then press . 35 Blinks o. To change the temperature, press or then press .
AP20BC175-2 Manual 20 t. To change the time, press or then press . 05 Blinks The display will show: NOTE: The defrost is done by running the evaporator fan for 5 minutes with the door open. PARAM. PROGRA MMING DEFROST CYCLE TOTAL TIME 05 MIN PARAM. PROGRA MMING DEFROST CYCLE PROGRAMMING COMPLETE MANUAL SOFT CYCLE PARAMETERS PROGRAMMING u.
AP20BC175-2 Manual 21 MANUAL HARD CYCLE PARA METERS PROGRAMMING A fter about 2 seconds the display will automatically change to: The LED for "M" will be "ON" . The LED'S for cycles will be blinking. aa. Press the button. The LED for "HARD" will be steady "ON" .
AP20BC175-2 Manual 22 The display will show: NOTE: PROGRAMMING F OR "DEFROST" WILL BE THE SAME IN MANU AL MODE AS IT IS IN AUTOMATIC MODE (see pages 19-20 PARAM. PROGRA MMING MANUAL HARD CYCLE PROGRAMMING COMPLETE ). 3. RECIPE NAME PROGRAMMING a.
AP20BC175-2 Manual 23 OPERATION 1. AUTOMATIC MODE - SOFT CHI LL a. With the display reading "OFF" , press the ( “ON/OFF” ) button. b. To select the soft cycle, press the appropriate bu tton . The LED for "SOFT" will be steady "ON" .
AP20BC175-2 Manual 24 The display will show briefly: Then the display will show: STARTING CYCLE . . . alternating with 00:00 Will count u p The AUTOMATIC mode uses both the food probes and air probe temperatures to control the cycle.
AP20BC175-2 Manual 25 The display will show briefly: Then the display will show: STARTING CYCLE . . . alternating with 01:29 Will count down The MANUAL mode uses time and the air prob e temperature to control the cycle. The default total time for a soft cycle is 90 minutes.
AP20BC175-2 Manual 26 b. Open the door. c. Press the ( "START/STOP") button to start the defrost cycle. READY TO START Blinks The display will show briefly: Then the display will now show: 04:59 Will count down to 00:00 After 5 minutes the display will show: The controller will beep for a few seconds.
AP20BC175-2 Manual 27 5. PREPARING AND USING THE PRINTER a. With the display reading "OFF" , press the ( “PRINT” ) button. b. To start printing, press the ( "START/STOP") button. After a few seconds the display will show: and the printer will be printing.
AP20BC175-2 Manual 28 y installed on the groove patterns to pop the front edge up. Lift off will facilitate the entry of the paper into d hold e. with the spindle onto the snaps REMOVING A ROLL OF PAPER the paper about one inch beyond the paper cutter.
AP20BC175-2 Manual 29 til the printer cover tilts up, then lift the cover completely off. e IBBON (WIT H PAPER IN THE PRINTER) ter. paper and into MAINTENANCE AND CLEANING 1. Turn the printer OFF. 2. Four small grooves are embossed on each side of the printer cover.
AP20BC175-2 Manual 30 C last chiller, it is necessary that the condenser be kept lean so that air can circulate around it freely and come into contact with the whole of its surface. OTE: If additional refrigerant should be needed, be certain to use the ct e an mount as shown on the nameplate.
AP20BC175-2 Manual 31.
AP20BC175-2 Manual 32.
AP20BC175-2 Manual 33.
AP20BC175-2 Manual 34 COMPUTER CONNECTION.
AP20BC175-2 Manual 35 PARTS LIST PART # DESCRIPTION 990059 PRINTER 990074 TRANSFORMER 208V/24V/12V 990075 TRANSFORMER F OR PRINTER 990103 ELECTRONIC BOARD "BLUE SYS" (D) 990104 PC CONNECTION.
AP20BC175-2 Manual 36 STANDARD WARRANTY AMERICAN PANEL CORP. 5800 S.E. 78th Street, Ocala, Florida 34472-3412 American Panel Corporation products are warranted to the original user installed within th.
AP20BC175-2 Manual 37 ORDERING PRINTER SUPPLIES (RIBBON & PAPER) Replacement paper and ribbons for the optional printe r for your blast chiller can be ordered from a local distributor of Weigh-Tronix supplies. To locate a distributor near you: If you have access to the internet: Go to www.
デバイスAmerican Panel AP20BC175-2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
American Panel AP20BC175-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAmerican Panel AP20BC175-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。American Panel AP20BC175-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。American Panel AP20BC175-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
American Panel AP20BC175-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAmerican Panel AP20BC175-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、American Panel AP20BC175-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAmerican Panel AP20BC175-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
