Harbor Freight Toolsメーカー05154の使用説明書/サービス説明書
ページ先へ移動 of 20
SANDER - 4” BEL T & 6” DISC Model 05154 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com Cop yr ight 2004 by Harbor F reight T ools ® . All rights reser ved.
PR ODUCT SPECIFICA TIONS GENERAL SAFETY RULES W ARNING! READ AND UNDERST AND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury . SA VE THESE INSTRUCTIONS W ORK AREA 1. Keep your work area clean and well lit.
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4.
11. Dress properl y . Do not wear loose clothing or je welr y . Contain long hair . K eep your hair , clothing, and gloves a way fr om moving parts. Loose clothes, je welr y , or long hair can be caught in moving par ts. 12. A v oid accidental star ting.
22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that ma y affect the tool’ s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 23. Use only accessories that are recommended by the manufacturer for your model.
3. Y our tool must be plugged into an appropriate outlet, proper ly installed and grounded in accordance with all codes and ordinances . The plug and outlet should look like those in the f ollowing illustration. (See Figure A.) FIGURE A SKU 05154 P A GE 6 DOUBLE INSULA TED T OOLS: T OOLS WITH TW O PR ONG PLUGS 1.
SKU 05154 P AGE 7 serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
SKU 05154 P A GE 8 SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions per Minute (RPM) no xxxx/min. A V ~ FIGURE D SPECIFIC SAFETY RULES 1. Maintain a safe working environment.
9. Store idle equipment. When not in use, tools and equipment should be stored in a dr y location to inhibit rust. Alwa ys lock up tools and equipment, and k eep out of reach of children. 10. Do not use this product if under the influence of alcohol or drugs.
21. Allow the Sanding Disc (11) and Sanding Belt (45) to spin up to full speed before f eeding a workpiece into them. When tur ning off the Sander , allow the Sanding Disc and Sanding Belt to slow down and stop on their own. Do not press against the Disc or Belt to stop them.
SKU 05154 P AGE 11 27. W ARNING! The war nings, precautions, and instructions discussed in this manual cannot cov er all possible conditions and situations that ma y occur . The operator must understand that common sense and caution are factors which cannot be built into this product, b ut must be supplied by the operator .
T o Install A Sanding Disc: 1. W ARNING! Prior to performing an y assembly pr ocedures, make sure the Power Switch (30) is in its “OFF” position and the Power Cord (29) of the Sander is unplugged from its electrical outlet. 2. Check to mak e sure the Disc (11) is free of dir t, oil, and other debr is .
SKU 05154 P AGE 13 FIGURE H LOCK SCREW (15) WORK T ABLE (13) ANGLE PLA TE (14) T o Adjust The Angle Of The Miter Guide: 1. The angle of the Miter Guide (21) may be adjusted to the right 0 to 45 degrees and to the left 0 to 45 degrees. (See Figure I.) 2.
SKU 05154 P AGE 14 T o Adjust For V er tical Sanding: 1. Slightly loosen the Lock Screw (20). (See Figure J.) 2. Raise the Belt F rame ver tically to the desired position. Then, retighten the Lock Screw (20) to lock the Belt Frame in place. (See Figure J.
6. Once the sanding procedure is completed, remove the workpiece from the Sand- ing Belt (45). T ur n the P ow er Switch (30) to its “OFF” position, and unplug the machine from its electrical outlet. (See Figure K.) WORKPIECE POWER SWITCH (30) WORK SUPPORT (33) T o P erf orm V er tical Sanding With The Sanding Belt: 1.
SKU 05154 P A GE 16 8. Once the sanding procedure is completed, remove the workpiece from the Sand- ing Belt (45). T ur n the P ow er Switch (30) to its “OFF” position, and unplug the machine from its electrical outlet.
SKU 05154 P A GE 17 7. Hold the workpiece firmly with one hand and the Miter Guide (21) with the other hand. Gradually push the workpiece into the Sanding Disc (12), allowing the Sanding Disc to cut without being forced. (See Figure M.) FIGURE M MITER GUIDE (21) 8.
5. When storing, make sure to store the Sander in a safe, clean, and dry location. PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIAGRAM IN THIS MANUAL AS A REFERENCE T OOL ONL Y .
SKU 05154 P AGE 19 P ARTS LIST NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not available individually as replacement parts.
SKU 05154 P A GE 20 ASSEMBL Y DIA GRAM & WIRING SCHEMA TIC NO TE: Some parts are listed and sho wn for illustration purposes onl y , and are not available individually as replacement parts.
デバイスHarbor Freight Tools 05154の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harbor Freight Tools 05154をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 05154の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 05154の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 05154で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 05154を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 05154の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 05154に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 05154デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
