Harbor Freight Toolsメーカー91062の使用説明書/サービス説明書
ページ先へ移動 of 17
3-1/4” ELECTRIC PLANER Model 91062 OPERA TING INSTR UCTIONS Due to continuing improv ements , actual product ma y diff er slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety warnings and precautions, assembl y , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in v oice with this manual.
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4.
11. Dress properl y . Do not wear loose clothing or je welry . Contain long hair . Keep y our hair , clothing, and gloves a wa y from mo ving par ts. Loose clothes, je welr y , or long hair can be caught in moving par ts . 12. A v oid accidental star ting.
20. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that ma y affect the tool’ s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 21. Use only accessories that are recommended by the manufacturer for your model.
3. Y our tool m ust be plugged into an appropriate outlet, proper ly installed and grounded in accordance with all codes and ordinances . The plug and outlet should look like those in the f ollowing illustr ation. (See Figure A.) FIGURE A SKU 91062 P A GE 6 DOUBLE INSULA TED T OOLS: T OOLS WITH TWO PR ONG PLUGS 4.
SKU 91062 P A GE 7 EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord.
FIGURE D SKU 91062 P A GE 8 SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions per Minute (RPM) n o xxxx/min. A V ~ SPECIFIC SAFETY RULES 1. Maintain a safe working environment.
8. Use ey e and breathing protection. Alwa ys wear ANSI approv ed saf ety impact eye goggles and dust masks or a respirator when working with this product. 9. Always turn off the Planer and unplug the unit from its electrical outlet before performing any maintenance, or changing accessories.
on their own. Do not press against the Kniv es to stop them. Alwa ys keep hands and fingers clear of spinning Blades. 23. Do not for ce the Blades into the workpiece being cut. Apply moderate pres- sure, allowing the Blades to cut without being forced.
OPERA TING INSTR UCTIONS NOTE: For additional information regarding the parts mentioned in the following pages, ref er to the Assemb l y Dia gram on pa g e 17. SKU 91062 P A GE 11 The Power Switch: 1. The T r igger (16) of the Planer f eatures a Safety Loc k Button (17) to ensure against accidental star ting of the tool.
SKU 91062 P A GE 12 The Guide: 1. The Guide (64) can be used to adjust the width of cut, suppor t the Planer , and keep the Planer from drifting away from the cut line (i.e., the edge of a door). The Guide may be attached either to the right side of the Planer or on its left side.
SKU 91062 P A GE 13 the wood stoc k . Then, transfer pressure to the Rear Base Plate , and continue planing slowly to the end of the cut. Do not pull the Planer back over the surface already cut. (See Figure G.) 6. If necessar y , repeat Step #5, using progressiv ely deeper cuts until you near the desired depth.
SKU 91062 P A GE 14 driver (not included) to remov e the two Carbon Brush Caps (35). Then, remov e the two Carbon Brushes from the Brush Holders (38). If a Carbon Brush is worn down more than 1/2 of its original length, replace both Carbon Brushes.
SKU 91062 P A GE 15 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUTOR HAS PR O VIDED THE P ARTS LIST AND ASSEMBL Y DIA GRAM IN THIS MANUAL AS A REFERENCE T OOL ONL Y .
Part # Description Qty. Part # Description Qty. 1 Name Plate 1 33 Screw Arbor 1 2 Tap Screw (8SEABB04-18) 3 34 Spring 1 3 Cover 1 35 Carbon Brush Cap 2 4 Belt 1 36 Carbon Brush 2 5 Bearing Sleeve 1 37.
SKU 91062 P A GE 17 17 16 18 ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts.
デバイスHarbor Freight Tools 91062の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harbor Freight Tools 91062をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 91062の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 91062の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 91062で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 91062を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 91062の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 91062に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 91062デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
