Harbor Freight Toolsメーカー98870の使用説明書/サービス説明書
ページ先へ移動 of 17
ARC WELDER - 120 Model 98870 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® .
Page 2- SKU: 98870 SPECIFICA TIONS Input Power 1 15/230 V~ , 42 A Maximum Amperage Output 120 A Electrode Sizes (Note: Electrodes not included) 1/16” to 5/64” (1 15V) 1/16” to 3/32” (230V) Features This is a high-quality hobby arc welder , delivering up to 140 Amps welding current.
Page 3- SKU: 98870 Use eye and ear protection . Wear ANSI-approved impact safety goggles at all times. Wear a full face shield if you are producing metal lings or wood chips. W ear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists.
Page 4- SKU: 98870 Safety W arnings and Precautions for Arc W elding W ARNING! Arc W elding Can be Hazardous. It is your responsibility to operate this equipment in a safe manner . Fire or Explosion Precautions Arc welding creates heat and sparks. These can cause re or explosion.
Page 5- SKU: 98870 Personal Safety Precautions Flying Sparks can cause injury , and Hot Materials can cause burns. Please wear appropri - ate safety clothing, and observe precautions to prevent burns or injury to yourself or others. Wear ANSI approved safety goggles or glasses when using this equipment.
Page 6- SKU: 98870 ARC WELDER ASSEMBL Y Installing the Handle Locate the HANDLE (27) and SCREW (28). Slide the HANDLE (27) onto the top of the CASE (26), indexing the tabs on the underside of the HANDLE onto the slots on top of the CASE, as indicated by lines (A) in Figure 1.
Page 7- SKU: 98870 Installing the Electrode Handle Figure 3. Installing the Electrode Handle Locate the ELECTRODE CABLE (5), as shown in the parts diagram, and the Elec- trode Handle as shown in gure 3, Step 1 above. Slide the Handle Grip off the Electrode Handle, as shown in Step 2 above.
Page 8- SKU: 98870 Installing the Power Plug Note: This Arc Welder is equipped to operate with either 1 15 or 230 V olt power supply . Standard “household” current in the U.S. is 1 10-120 V olts. If you will be using a “household” outlet, follow directions for 1 15 V olt wiring.
Page 9- SKU: 98870 Wiring Diagram 1 15/230 V~ 1 15 V~: B - M 230 V~: M - N B=White N=Red M=Black.
Page 10- SKU: 98870 Preparing a Safe W orkplace Environment to A void Hazardous Conditions The primary hazards to be managed when using Arc Welding equipment include Electric Shock, Fumes and Gasses, Sparks and Fire, Arc Light, and T ools and Equipment in the Work Area.
Page 1 1- SKU: 98870 General Workplace Cautions Prepare and maintain a safe, uncluttered workplace. Make sure the welding ground circuit is direct to the work. Be wary of hoist chains, cables, scaffolding, etc. Avoid contacting other electrical equipment in the area, such as hoists, grinders, etc.
Page 12- SKU: 98870 CONTROLS POWER SWITCH (1). Use this selec- tor to turn the welder Off, or On to the correct V oltage. WARNING: It is imperative that you select ONL Y the V oltage setting for which you have wired the Power Cable. POWER CABLE (2). Y ou will have wired this for either 1 15 or 230 V olts.
Page 13- SKU: 98870 important information, you are strongly urged to obtain appropriate training, and to practice on non-critical test pieces before attempting to weld important items.
Page 14- SKU: 98870 T roubleshooting Arc W elding Defects Porosity and Surface Holes Most porosity cannot be seen, but serious porosity weakens the weld. Before welding, remove all surface contaminants, such as Mill Scale, Rust, Paint, Dirt, Grease, or Moisture.
Page 15- SKU: 98870 Parts List Part Code Q’ty Description 1 ZH-HC-3 1 SWITCH 1 15/230V 2 BA.B12.6 1 POWER CABLE 3 BA.B12.4 1 AMPERAGE CONTROL KNOB 4 BA.B12.7 1 GROUND CABLE 5 BA.B12.7 1 ELECTRODE CABLE 6 ND10 T90 1 GREEN PILOT LAMP 7 ND10 T90 1 YELLOW LAMP 8 GB818 3 SCREW M4 X 12 9 1 WELDING STEP SELECT OR 10 GB818 1 SCREW M 3 x 10 1 1 BA.
Page 16- SKU: 98870 Assembly Diagram 29.
Page 17- SKU: 98870 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original.
デバイスHarbor Freight Tools 98870の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harbor Freight Tools 98870をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 98870の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 98870の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 98870で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 98870を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 98870の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 98870に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 98870デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
