Hearth and Home TechnologiesメーカーSMART-BATT-IIの使用説明書/サービス説明書
ページ先へ移動 of 12
1 Printed in China Copyright 2006, Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 5504 100-909 G 12 /06 SMART -BA TT -II Remote Control Kit s - Installation and Operating Instructions - INTRODUCTION The remote control system can be operated thermostati- cally or manually from the transmitter .
2 RECEIVER WIRING INSTRUCTIONS Incorrect wiring connections WILL cause damage to the gas valve or electronic module operating the gas appliance and may also damage the remote receiver .
3 Figure 4. Millivolt with Rocker Switch and Receiver Figure 5. Millivolt with 3 Wire If your fireplace is wired like Figure 3 find the leads on back of the switch marked “For use with remote or wall switch only” and take the leads and plug them into wire lead on remote receiver box (see Figure 4).
4 Figure 6. Millivolt with Receiver Figure 7. Intermittent Pilot Ignition (IPI) Wiring Diagram IGNITION MODULE 3 V AC GRN ORG INTE RMITTE NT PIL OT IGNITOR ORG WHT VA LV E PIGGYBACK ON/OFF SWIT CH BRN.
5 Figure 8. Intermittent Pilot Ignition (IPI) Wiring Diagram If your fireplace look like Figure 7 find the leads on the back of switch marked “For use with remote or wall switch only”. T ake the leads and plus them into wire leads on remote receiver box (see Figure 8).
6 Figure 9. If your fireplace looks like Figure 9 remove the 3-wire off the jumper wire by unplugging the spade from jumper wire. Install the jumper wire on the wire as shown see Figure 10. Then install one of the leads from the remote receiver onto the valve and other wire into the lead on the jumper wire.
7 NOTE: The remote receiver houses the microprocessor that responds to commands from the transmitter to control sys- tem operation. It emits one beep when it receives an ON or OFF command manually , but no beep when cycling on and off automatically in THERMO mode.
8 MA TCHING SECURITY CODES It may be necessary to program the remote receiver to the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer . T o program the remote receiver: 1.
9 SE TTIN G BUTTO N Figure 13. Setting Button/Child Proof Lockout Setting 0 F/ 0 C Scale The factory setting for temperature is degrees Fahrenheit ( 0 F).
10 TRANSMITTER SAFETY FEA TURES It is recommended that the TRANSMITTERS always be lo- cated within a 20 foot operating range of the fireplace, pref- erably in the same room in which the fireplace system is located.
11 4. Then press the MODE button on the transmitter to change the system to ON. The spark electrode should begin sparking to ignite the pilot. After the pilot is lit, the main gas valve should open and the main gas flame should ignite. 5. Press the MODE button on the transmitter to OFF .
12 Limited W arranty This REMOTE CONTROL SYSTEM is warranted for 12 months from the date of purchase or installation to the original purchaser to be free from defects in mate- rials and workmanship.
デバイスHearth and Home Technologies SMART-BATT-IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hearth and Home Technologies SMART-BATT-IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHearth and Home Technologies SMART-BATT-IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hearth and Home Technologies SMART-BATT-IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hearth and Home Technologies SMART-BATT-IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hearth and Home Technologies SMART-BATT-IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHearth and Home Technologies SMART-BATT-IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hearth and Home Technologies SMART-BATT-IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHearth and Home Technologies SMART-BATT-IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
