Hitachiメーカー42PD6700Uの使用説明書/サービス説明書
ページ先へ移動 of 39
42PD6700U GB Instructions for use.
- 1 - Contents Remote Control Buttons ......................... 2 PLA SMA TV ............................................. 4 Preparation ............................................. 6 Fe at ur es ............................................... 6 Panel Features .
- 2 - Remote Control Buttons .
- 3 - = S tand by On/Off = Program Information SEL= Select TV/ DVD /SA T AV 3 = AV 3 m o d e AV 2 = AV 2 m o d e RGB2 = No Function RGB1= PC mode = Go back to previous menu ` = Cursor Right OK = Enter.
- 4 - PLASMA TV FRONT VIEW REAR VIEW.
- 5 - On/Off switch V olume Up, V olume Down buttons Prog. Up, Prog. Down buttons MENU button TV/A V button Power cord input S-VHS Input Video Input Audio Inputs Headphone Audio Line Outs Subwoofer Ou.
- 6 - Preparation For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. Use this apparatus in tropical and/or moder- ate climates. Features Remote controlled colour television.
- 7 - Observe the manufacturers instructions when connecting extension leads to the TV . Check the fuse rating on the new plug, this should be fitted with a 5 Amp fuse which conforms to ei- ther AST A or BSI (BS1 362) approvals, these are easily identifiable by either the o r symbols.
- 8 - The Plasma TV is a very high techology product giving you fine picture details. Occa- sionally, a few non-active pixels may remain still on the screen. Long-time unmoving still pictures may cause permanent shade effect on the screen and even the picture has been changed, its influence lasts as ghost pic- ture.
- 9 - Before Switching On Y our TV Power Connection IMPORTANT: The TV set is designed to op- erate on 220-240V AC, 50 Hz. After unpacking, allow the TV set to reach the ambient room temperature before you con- nect the set to the mains.
- 10 - Initial Settings When the TV is turned on for the first time, it is in the digital mode. Because this is the first time the TV is used, there are no channels stored in the memory and the following message appears on the screen . To start installation process, select Yes, to cancel select N o .
- 11 - Operating The TV You can operate your TV using both the re- mote control handset and the buttons on the set. Operating with the buttons on the TV set Volume setting and programme selection can be made by using the buttons on the control panel at the bottom of the TV.
- 12 - Navigating the whole channel list Press o r button for selecting the previ- ous or next channel. To watch a specific channel, highlight the Select item in the channel list using the or button. Then using the o r button select the desired channel and press the OK button.
- 13 - Select the channel to be locked by highlight- ing it and select the Lock option by press- ing o r button. When the OK button is pressed, a password box is displayed. Enter the password using the digit buttons on the remote control.
- 14 - menu. All the services are searched and a channel table is created automatically. All channels found are stored in a sorted form with respect to their channel numbers. Some services may not appear with the cor- rect channel number. At the time of printing, not all broadcasters are sending their chan- nel number information.
- 15 - The various configuration functions are dis- played in a list, along with a quarter-screen image of the currently selected channel. You can select a function by highlighting the cor- responding menu line using the o r but- ton .
- 16 - Both automatic upgrade methods result in standby mode either upgraded or not. If the automatic upgrade is set to Disabled then this function will not work.
- 17 - To set an event, highlight its mode button using the o r button and press the OK button to display the timer entry window. Here the five settings of channel name, start time, end time, date and frequency mode can be set. You can move freely be- tween each setting using the o r but- tons.
- 18 - press the OK button to display TV Setup menu screen. Detailed information about Sound, Picture and Feature menus are in AnalogueTV Menu System section on page 18. Common Interface Press the button to display the Main Menu and use the o r button to highlight the Common Interface line and press the OK button.
- 19 - Picture menu By pressing _ / ` button, select the first icon. Picture menu appears on the screen. Mode By pressing a / b button, select Mode . Press _ / ` button to choose one of these options: Natural , Dynamic and Cinema . Picture mode can be changed directly by pressing the button.
- 20 - Reset By pressing a / b button, select Reset. Press _ / ` or OK button to reset the picture modes to factory default settings. Sound menu By pressing _ / ` button, select the second icon. Sound menu appears on the screen. V olume By pressing a / b button, select Volume.
- 21 - balance By pressing a / b button, select Balance. Press ` button to increase balance to the right. Press _ button to decrease balance to the left. Balance level can be adjusted be- tween -31 and 31. Press the button to return to the previous menu.
- 22 - ton to either on o r off . When off is selected, there will be no difference in the operation of your TV. When on is selected, the TV can only be controlled by the remote control handset. In this case the control panel but- tons, except the Power on/off button, at the bottom of the TV will not work.
- 23 - 5 mins but try not to leave static images on the screen for long periods of time. Install menu By pressing _ / ` button, select the fourth icon. Install menu appears on the screen. Program By pressing a / b button, select Program. Press _ / ` button to select the program number.
- 24 - the programmes in TV mode (except the AV mode). By cursor action, programme selection is done automatically. Name: To change the name of a decided programme, select the programme and press the RED button. The first letter of the selected name starts to blink.
- 25 - Set your PCs resolution correctly before connecting to the TV . See the table on pa g e 34 for supported modes. Use a D-SUB cable to connect the TVs PC input to the computers RGB output termi- nal. Tighten the screws of the Display cable until the connectors are fastened securely (fin- ger-tighten only).
- 26 - Contrast, Brightness and Colour Tempera- ture adjustments in this menu are identical to adjustments defined in TV picture menu. When Colour Temp is Manual, you can also adjust the R,G,B items.
- 27 - Zoom Modes Zoom mode can be changed by pressing the button. You can change the screen size according to the picture aspect ratio. Select the optimum one from the following ZOOM modes.
- 28 - To Operate Teletext Select a TV st ation where T eletext is being transmitted. Press the button. Usually the list of con- tents (index) is displayed on the screen. To Select A Page Of Teletext Press the appropriate digit buttons for the required T eletext page number .
- 29 - screen backward one page at a time. For Fastext The subject-heading for the information may have a particular colour. Press an appropriate RED , GREEN , YELLOW or BLUE button in order to reach the relevant page quickly . F o r T O P t e x t TOP text mode of operation will be activated automatically according to the transmission.
- 30 - Copy Facility Source selection for VCR recording. Select Feature menu. Select Av-2 Out by pressing _ / ` button. Select a source to copy the picture from that source. Search For And Store The Test Signal Of The Video Recorder Unplug the aerial cable from the aerial socket of your video recorder .
- 31 - Aerial Connection Connect Peripheral Equipment.
- 32 - your decoder and to the special Scart socket of your video recorder . Refer to the booklet of your video recorder . T o connect your video recorder to the TV , re- fer to the TV and Video Recorder section. If you want to connect more equipment to your TV, consult your dealer.
- 33 - Specifications TV BROADCASTING PAL/SECAM B/G D/K K' I/I' L/L' RECEIVING CHANNELS VHF (BAND I/III) UHF (BAND U) HYPERBAND CABLE TV (S1-S20/ S21-S41) NUMBER OF PRESET CHANNELS 1 0 0 CHANNEL INDICA TOR On Screen Display RF AERIAL INPUT 75 Ohm (unbalanced) OPERA TING VOL T AGE 220-240V AC, 50 Hz.
- 34 - Appendix A: PC Input T ypical Display Modes The display has a maximum resolution of 1280x 1024, vertical sync. frequency range of 56- 85 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes.
- 35 - Appendix B: DVD Player Selection You can use this remote control to operate the selected brand of DVD player by pressing the following buttons on the remote control simultaneously. Example T o operate HIT ACHI DVD player , press and hold the INFO button, followed by the 1 button.
Appendix C: Main and PIP-P A P Picture Combinations - 36 -.
UK Guarantee Your Guarantee of Excellence Thank you for purchasing this Hitachi Television. In the unlikely event that this product should develop a fault, we undertake to replace or repair any part o.
HIT ACHI EUROPE L TD. UNITED KINGDOM Consumer Affairs Department PO Box 3007 Maidenhead Berkshire SL6 8ZE T el: 0870 405 4405 Email: HIT ACHI EUROPE GmbH GERMANY HIT ACHI EUROPE S.
デバイスHitachi 42PD6700Uの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hitachi 42PD6700Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHitachi 42PD6700Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hitachi 42PD6700Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hitachi 42PD6700Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hitachi 42PD6700Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHitachi 42PD6700Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hitachi 42PD6700Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHitachi 42PD6700Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。