HitachiメーカーCPX385Wの使用説明書/サービス説明書
ページ先へ移動 of 44
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS NORSK PORTGÊS 中 中 文 文 REGULATORY NOTICES USER'S MANU AL Vol.1 Basic Please read this user's manual thoroughly to ensure correct usage through understanding.
1 LCD Projector CPX385W USER'S MANUAL USER'S MANUAL V ol.1 (Basic) Page PROJECTOR FEATURES ................2 PREPARATIONS ..............................2 PART NAMES ...................................4 SETTING UP THE PROJECTOR ..............
2 ● Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system ● Partial Magnification Function Interesti.
3 1 Connect your devices to the projector Connect your computer, VCR and/or other devices you will be using to the projector. Insert the batteries into the remote control 2 13 3 Connect the power cord (1) Connect the connector of the electrical power cord to the AC inlet of the main unit.
4 P AR T NAMES THE PROJECTOR Indicates the corresponding reference page Power Switch AC Inlet (to the Power Cord) Ventilation Openings (Intake) Zoom Ring Focus Ring Remote Control Sensor Lens Lens Cap.
5 THE REMOTE CONTROL RGB button 15 VIDEO button 15 KEYSTONE button 20 ENTER button 23 RESET button 18 BLANK button 22 LASER button 5 MOUSE / RIGHT Button 24 Disk Pad 24 MENU button 23 AUTO button 19 ,.
6 Angle Adjustment 1 Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle. 2 Release the button to lock at the desired angle. 3 Turn the rear foot adjuster to adjust the left-right slope. Do not force the foot adjuster screws.
7 Refer to the illustrations and tables below to determine the screen size and projection distance. Adjusting the Screen Size and Pr ojection Distance If 4:3 aspect ratio 4 3 The values shown in the t.
8 Display monitors 12 DVD players 11 VCRs 11 Laptop computers 10 Desktop computers 10 Indicates the corresponding reference page ATTENTION Precautions to observe when connecting other devices to the projector • Whenever attempting to connect other devices to the projector, please thoroughly read the manual of each device to be connected.
9 Ports and Cables Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare. About Plug-and-Play Capability • This projector is compatible with VESA DDC 1/2B.
10 B A AUDIO IN AUDIO cable RGB cable AUDIO OUT RGB IN Analogue RGB OUT AUDIO IN VIDEO IN S-VIDEO IN AUD IO IN AUDIO OUT 1 12 2 USB RGB IN RGB OUT CONTROL A B Laptop computer B A D C USB IN USB OUT AU.
11 B C A If using a component video connection If using an audio/video connection COMPONENT VIDEO IN COMPONENT VIDEO OUT AUDIO/VIDEO IN AUDIO/VIDEO OUT S-VIDEO IN S-VIDEO OUT If using a S-video connec.
12 RGB cable A RGB OUT RGB IN AUDIO IN VIDEO IN S-VIDEO IN AUD I O IN AUDIO OUT 1 12 2U S B RGB IN RGB OUT CONTROL A CONNECTING Y OUR DEVICES (continued) Connecting to a Display Monitor Display monitor 01CPX385/EN最終 02.
13 1 Remove the battery cover Push the knob while lifting up the battery cover in the direction of the arrow. Insert the batteries Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicated in the remote control).
14 1 Make sure that the power cord is firmly and correctly connected to the projector and outlet 2 Turn on the projector's power Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange.
RGB 15 6 Use the zoom ring to adjust the screen size 7 Use the focus ring to focus the picture 5 If selecting RGB input Press the RGB button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2.
16 ST ANDBY/ON LASER BLANK RGB VIDEO AUT O MENU ENTER KEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ON VOLUME MUTE 1 Press the STANDBY/ON button (control panel or remote control) The message "Power off?" will appear on the screen for approximately 5 seconds.
17 ST ANDBY/ON LASER BLANK RGB VIDEO AUT O MENU ENTER KEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ON VOLUME SEARCH MUTE 1 Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.
18 ST ANDBY/ON LASER BLANK RGB VIDEO AUT O MENU ENTER KEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ON VOLUME SEARCH MUTE 1 Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.
19 The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals. NOTE 1 USING THE A UT OMA TIC ADJUSTMENT FEA TURE Press the AUTO button Horizontal position (H. POSIT), vertical position (V.
20 • This function may not be work well with some types of input signals. • The adjustable range for correcting keystone distortions will vary with the type of input signal. NOTE CORRECTING KEYST ONE DIST ORTIONS 1 Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.
21 The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT, AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
22 SIGNAL SEARCHING SELECTING THE ASPECT RA TIO TEMPORARIL Y BLANKING THE SCREEN 1 Press the SEARCH button When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal.
23 USING THE MENU FUNCTIONS 1 Press the MENU button The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, SCREEN, and OPTION. Select a menu using the / buttons. The current settings of the items that can be manipulated via the selected menu appear.
24 You can use the remote control as a simplified mouse or keyboard. OPERA TING THE PC SCREEN CAUTION Caution: Mistaken use of the mouse/keyboard control could damage your equipment. • Only connect to a PC. • Before connecting, read the manuals of the device you will connect.
25 THE LAMP HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately: DT00431), then contact your local dealer.
26 • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp. NOTE THE LAMP (continued) Replacing the lamp All projector lamps will wear out eventually.
27 THE AIR FIL TER Caring for the air filter The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned.
28 THE AIR FIL TER (continued) Replacing the air filter If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the model of your separately sold replacement air filter.
29 Fixing the Handle THE HANDLE Caring for the inside of the projector : In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself.
TECHNICAL ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS NORSK PORTGÊS 中 中 文 文 Liquid Crystal Projector CPX385W USER'S MANU AL Vol.2 Extended Please read this user's manual thoroughly to ensure correct usage through understanding.
1 LCD Projector CPX385W USER'S MANUAL USER'S MANUAL V ol.2 (Extended) Thank you for purchasing this projector. • The information in this manual is subject to change without notice.
MAIN Menu Item Description BRIGHT Adjust Brightness: Light ⇔ Dark CONTRAST Adjust Contrast: Strong ⇔ Weak ASPECT Select Aspect Ratio: At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT.
PICTURE 1 Menu PICTURE 2 Menu With the PICTURE 1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. With the PICTURE 2 menu, the five items shown in the Table below can be performed.
MUL TIFUNCTIONAL SETTINGS (continued) INPUT Menu With the INPUT menu, the four items shown in the Table below can be performed. With inputting of RGB IN 1 and RGB IN 2 signals, the horizontal and vertical frequencies of the signals will be displayed on the initial screen of the INPUT menu.
SCREEN Menu With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. 5 SCREEN Menu Item Description BLANK Selection of BLANK Screen: MyScreen ⇔ ORIGINAL ⇔ .
MUL TIFUNCTIONAL SETTINGS (continued) OPTION Menu With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
WHA T T O DO WHEN Y OU THINK A MA CHINE DEFECT HAS OCCURRED Related Messages When the unit's power is ON, messages such as those shown below may be displayed.
Regarding the Indicator Lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below.
9 WHA T T O DO WHEN Y OU THINK A MA CHINE DEFECT HAS OCCURRED (continued) Phenomena That May Easily Be Mistaken for Machine Defects Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.
Dimension Diagram Unit : mm 298 94.6 54 228 241.5 76 76.5 Item Specification Product name Liquid crystal projector Liquid crystal panel Panel size 2.3 cm (0.9 type) Drive system TFT active matrix Pixels 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=1.
If a problem occurs with the equipment, first refer to the “WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.
01CP-X385W/Vol2-E 02.11.7 3:53 PM ページ 12.
Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 – 12 Nishi Shinbashi, 2 – Chome, Minato – Ku, Tokyo 105 - 8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD. HITACHI EUROPE S.A. Dukes Me adow 364, Kifissias Ave.
デバイスHitachi CPX385Wの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hitachi CPX385Wをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHitachi CPX385Wの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hitachi CPX385Wの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hitachi CPX385Wで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hitachi CPX385Wを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHitachi CPX385Wの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hitachi CPX385Wに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHitachi CPX385Wデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。