HitachiメーカーNB5741XDの使用説明書/サービス説明書
ページ先へ移動 of 24
• Single-phase Input 100V Class Manual No . NB5741XD • December 2003 Hitachi Industrial Equipment Systems Co., Ltd. HIT A CHI L100-M Series In ver ter Quic k Reference Guide.
1 Caution: Be sure to r ead the L100 In verter Manual and follow its Cautions and W arni ngs for the initial product installation. This Quick Refe r ence Guide is intended for r eference use by e xperienced users in servicing existing installations.
2 Contr ol Circuit T erminals Te r m i n a l Name Description Ratings and Notes P24 +24V for logic inputs 24VDC supply , 30 mA max. (Notes: Do not use for network power Do not short to terminal L) 1, 2, 3, 4, 5 Intelligent (program- mable) discrete logic inputs 27VDC ma x.
3 O Analog input, voltage 0 to 9. 6 VDC range, 10VDC nominal, 12 VDC max., input impedance 10 k Ω H +10V analog reference 10VDC nominal, 10 mA max. AL0 Relay common contact C ontact rating Max resistive load = 250V A C, 2.5A; 30VDC 3A; Max inductive load = 250V A C, 0.
4 Basic Wiring Diag ram The following wirin g diagram shows the power and motor c onnec- tions for basic operation. The optio nal signal input wiring supports external Fwd and Re v Run command, and a speed potentiometer .
5 In ver ter K eypad Operatio n • Run/Stop LED – ON when the inverter output is ON and the motor is de veloping torque, and OF F when the in verter output is OFF (Stop Mode). • Progra m/Monitor LED – ON when the in verter is ready for parameter editing (Program Mode) .
6 • Potentiometer – Allows an operator to directly set the motor speed when the potentiometer is enab led for output frequ ency control. • Potentiometer Enable LED – ON when the potentiometer is enabled for value entry . • Para meter Displ ay – A 4-digit, 7-segmen t display for parame- ters and function codes.
7 Ke ypad Navigation Map c9 1 c0 1 1 2 b 89 b 01 1 2 A9 8 A0 1 1 2 1 2 1 2 1 2 C– – 1 2 b –– 1 2 A– – F0 4 F0 1 1 2 d 09 d 01 1 2 o.0 12 3 . 4 Edit 1 2 Increment/ decrement val ue Write data to EEPROM Displa y data Monitor Mode Program Mode FUNC.
8 P owerup T est The Power up T est procedure uses minimal parameter settings to run the motor . The proced ure describes two alternati ve methods for commanding the in verter: via the in verter keypad , or via the logic termin als . • Check po wer input and motor output wiring (see page 4 diagram).
9 Err or Codes The L100 series inv erters will trip on ov er-current, over -voltage, and under-voltage to protect the in verter . The motor output turns OFF , allowing the motor to free-run to a stop. Press the Stop/Reset ke y to reset the inv erter and clear the er ror .
10 Erro r T rip Conditions Use function code D_08 to access th e error trip conditions for the current error as shown in the table below . Use the Up and Down arrow ke ys to scroll through the trip condition parameters. E35 Thermistor • Thermistor input, [THM] and [L], is over the temp.
11 Restoring Factory Default Settings Action Display Function/Parameter Press , or as needed. b -- “B” Group selected Press . b 01 First “B” Group parame- ter Press/hold until... b 85 Coun try code for initialization selected Press . If setting is correct, then skip next step.
12 Note: After initializing the inverter , us e the P owerup T est on pag e 8 to get the motor running again. Pa ra m e te r T a b le s “D” Gr oup: Monitoring Functio ns Func.
13 T rip History Na vigation Map E0 7 60 . 0 1 2 4. 0 0 27 0 . 0 1 2 1 2 d 08 1 2 o.0 0 Displa y data Monitor Mode 1 2 FUNC. FUNC. d 09 ____ No Error code Output frequency at trip point Motor current at trip point DC bus voltage at trip point FUNC. Ye s No error Error (n-1) ex is ts ? No Ye s E0 3 E0 5 ____ No history FUNC.
14 Parameter tables for user-settable functions follo w these conven- tions: • Some parameters specify an op tion code. Where applicable, the options codes will be in a bulleted list in the Name/Description column. • The default v alues apply to all models unless otherwise noted for each parameter.
15 “A” Group: Standard Functions Func. Code Name / Description Default Va l u e –FE / –FU / –FR Set Va l u e A_01 Frequency source setting • 00 Ke ypad pot entiometer • 01 Control termin.
16 A_41 T orque boost method selection • 00 Manual torque boost • 01 Automatic torque boost 00 A_42 Manual torque boost value 11 A_43 Manual torque boost frequ ency adjust- ment 10.
17 “B” Gr oup: Fine-tuning Fu nctions A_82 A VR voltage select 230/230/200 400/460/400 A_92 Acceleration (2 ) time setting 15.0 A_93 Deceleration (2 ) time setting 15.0 A_94 Select metho d to switch to Acc2/Dec2 profile • 00 2CH input from terminal • 01 transition frequency 00 A_95 Acc1 to Acc2 frequency transition point 0.
18 B_12 Lev el o f electronic ther mal setting Rated current of each in verter B_13 Electronic thermal character istic • 00 Reduced torque • 01 Const.
19 “C” Gr oup: Intelligent T erminal Functions B_88 Rest art mode after FRS • 00 Restart from 0Hz • 01 Restart from frequency detected from actual speed of motor 00 B_89 Data select for di git.
20 C_21 T erminal [11] functi on Six option codes av ailable (see page 22) 01 C_22 T erminal [12] function 00 C_23 [FM ] signal selection Three option codes av ailable (see page 22) 00 C_31 T erminal .
21 Intelligent Input T erminal Listing Symbol Code Input T erminal Name FWD 00 Forw ard Run/Stop R V 01 Re verse Run/Stop CF1 02 Multi-speed select, Bit 0 (LSB) CF2 03 Multi-speed select, Bit 1 CF3 04.
22 Intelligent Output T erminal Listing Analog Inpu t Configuration The following tables show the parameter settings required for vari- ous analog input signal types.
23 Notes:.
デバイスHitachi NB5741XDの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hitachi NB5741XDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHitachi NB5741XDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hitachi NB5741XDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hitachi NB5741XDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hitachi NB5741XDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHitachi NB5741XDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hitachi NB5741XDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHitachi NB5741XDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。