HobartメーカーFP400の使用説明書/サービス説明書
ページ先へ移動 of 16
701 S. RIDGE AVENUE TROY, OHIO 45374-0001 N S T R U C T I O N S I FORM 33966 Rev. A (11-98) MODEL FP400 FOOD PROCESSOR ML-104751.
– 2 – T ABLE OF CONTENTS MODEL FP400 FOOD PROCESSOR ............................................................................................. 3 GENERAL ...........................................................................................
– 3 – © HOBART CORPORATION, 1998 MODEL FP400 FOOD PROCESSOR (Shown with Feed Hopper Attachment).
– 4 – Installation, Operation and Care of HOBART MODEL FP400 FOOD PROCESSOR PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL The FP400 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits, or cheese.
– 5 – VERIFY CORRECT ROTATION Verify correct rotation of the knife shaft. Make sure it moves in a clockwise direction looking down into the feed cylinder. If the rotation is incorrect, UNPLUG THE ELECTRICAL CORD and interchange any two of the three power supply leads (non grounding wires) inside the plug.
– 6 – OPERA TION WARNING: ROTATING KNIVES INSIDE. ALWAYS USE THE FEED HOPPER OR PUSHER PLATE FEED ATTACHMENT. KEEP HANDS OUT. Proper assembly of the FP400, including selection of the appropriate cutters, is necessary for correct operation of the food processor.
– 7 – INSTALLING THE CUTTING TOOLS Always push the red STOP button before changing cutters. Slicing, Shredding, Grating, and Julienne Cutting 1. Pull the locking handle forward and swing the feed cylinder out to the rear. 2. Place the ejector plate (Fig.
– 8 – 4. Screw the decoring screw (if using the pusher plate feed attachment) (left-hand thread) OR the agitator device (if using the feed hopper attachment) (left-hand thread) into position in the cutting tool center. 5. Release the catch, swing the feed cylinder back into position, and raise the locking handle.
– 9 – Fig. 7 INSTALLING AND REMOVING THE FEED ATTACHMENTS The feed hopper attachment (Fig. 7) is used mainly for cutting round products up to 3" (76 mm) in diameter. The pusher plate feed attachment (Fig. 8) can be used for any type product. Fig.
– 10 – Pusher Plate (Use the decoring screw to secure the plates to the knife shaft.) 1. Press the STOP button. 2. Fit the feed cylinder with three internal knives (see Fig. 8). 3. Move the pusher plate handle (Fig. 10) all the way up. 4. Insert the pusher plate attachment shaft (Fig.
– 11 – USING THE FOOD PROCESSOR When using the feed hopper attachment, bulk product may be added to the feed hopper during operation. When using the pusher plate feed attachment, place prepared products, such as potatoes, carrots, onion, lettuce, cabbage, etc.
– 12 – Crimping Slicer 3 ⁄ 16 CR (4.5 mm) Ripple cuts root vegetables (beets, potatoes, carrots, etc.) Julienne Cutters Julienne Cutter 3 ⁄ 32 (2.
– 13 – CLEANING WARNING: TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING. Clean the machine immediately after each use. Dismantle all removable parts from the machine and wash them in warm water and a mild detergent. Rinse thoroughly and wipe dry with a soft clean cloth.
– 14 – 2. Remove the feed cylinder. The feed cylinder guides (see Fig. 7) OR the three knives (see Fig. 8) may be removed for cleaning by unscrewing the nuts (see Fig's. 7 & 8) with the wrench provided. Rinse all parts with lukewarm water.
– 15 – TROUBLESHOOTING SYMPTOM Machine will not start or stops while operating and won't restart. Low output or poor cutting results. POSSIBLE CAUSE 1 . Machine plug not installed securely into receptacle. 2. Feed cylinder not locked in correct position.
– 16 – SYMPTOM Cutting tool locked to shaft. Decoring screw or agitator device cannot be removed. POSSIBLE CAUSE Build-up between cutting tool and dicing grid or potato chip grid. Devices have tightened during use of the machine. SUGGESTED ACTION Always use the ejector plate.
デバイスHobart FP400の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart FP400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart FP400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart FP400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart FP400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart FP400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart FP400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart FP400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart FP400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
