HobartメーカーHFB6の使用説明書/サービス説明書
ページ先へ移動 of 16
701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 34485 (May 2000) MODEL HFB6 ELECTRIC OVEN MODEL HFB6 ML-126878 ML-126880 N S T R U C T I O N S I.
– 2 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking .
– 3 – Installation, Operation, and Care of MODEL HFB6 ELECTRIC OVEN SAVE THESE INSTRUCTIONS GENERAL Your Hobart Flash Bake oven is a versatile oven that employs a revolutionary high quality, high-speed cooking technology. The baking process is so fast that food retains its natural juices.
– 4 – Fa n Flexib le Duct (By Others) O VEN REAR P ower Cord Duct Clamp (By Others) Blower PL-53483 INSTALLATION CODES AND STANDARDS The HFB6 Flash Bake oven must be installed in accordance with: In the United States of America: 1. State and local codes.
– 5 – ELECTRICAL CONNECTION — (Hard Wired Ovens) WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT THE ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE YOU ARE WORKING ON THE CIRCUIT.
– 6 – START-UP TESTING After the oven is connected to the supply circuit, perform the following tests to ensure that the oven is operating properly. Lamp Test Turn the oven on by pressing the ON/OFF button. After a few seconds, the display will settle on Recipe 1.
– 7 – OPERA TION WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, OR SERVICING THE OVEN. PRECAUTIONS • Never attempt to open the oven door while a cook cycle is in progress. Never attempt to operate the oven with the door open.
– 8 – CONTROLS — Model HFB6 DISPLAY The display screen, located at the top of the control panel provides a constant indication of the oven status. It is also used for programming the oven and for the display of information and diagnostic messages.
– 9 – TO START COOKING You can start cooking immediately by choosing a cook mode, a length of time and pressing the START button. Press one of the four cook mode buttons (HI, MED, LO, or BROWN). Then enter the desired cook time in minutes and seconds( up to 99:99 max.
– 10 – PASSWORD PROTECTION FOR PRESETS This oven comes with an optional password protection to prevent accidental changes to the settings stored in the nine preset locations. To Enter a Password 1. Press and hold down the “1” button and press the “6” button simultaneously.
– 11 – CLEANING WARNING: DISCONNECT ELECTRICAL SUPPLY BEFORE CLEANING THE OVEN. WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, OR SERVICING THE OVEN. The interior cleanliness of the Flash Bake oven is essential to ensure maximum efficiency of your oven.
– 12 – 4. To start the interior cleaning, use a cloth dampened with one of the recommended cleaners. Be sure that the soap is non-caustic. Wipe the food debris out of the oven, working from the back forward. Do not pour cleaning liquids into the oven.
– 13 – OVEN DOOR LAMP SHIELD RAIL UPPER LAMP SHIELD LIFT LAMP SHIELD OVER RET AINING FEA TURE PULL LAMP SHIELD T OWARD YOU LOWER LAMP SHIELD (NON REMOV ABLE) PL-52646 REMOVING AND INSTALLING THE TOP LAMP SHIELD Turn the oven off before removing the lamp shield.
– 14 – MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE OVEN. WARNING: DISCONNECT THE ELECTRICAL SUPPLY BEFORE PERFORMING ANY MAINTENANCE ON THE OVEN. Do not remove the oven covers or attempt to open the control cabinet.
– 15 – PROBLEM No power to the oven. No power to the oven controls or display. Blower not operating. Oven not cooking. Display screen does not light up. Grill does not rotate. Door does not lock. No "High Power". TROUBLESHOOTING POSSIBLE CAUSES 1.
– 16 – FORM 34485 (May 2000) PRINTED IN U.S.A. ERROR MESSAGES Under certain conditions, the oven will emit a short trill tone alarm when the operator presses a button.
デバイスHobart HFB6の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hobart HFB6をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart HFB6の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart HFB6の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart HFB6で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart HFB6を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart HFB6の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart HFB6に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart HFB6デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。