HobartメーカーHGFR ML-132079の使用説明書/サービス説明書
ページ先へ移動 of 24
701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 35504 Rev. A (Mar. 2005) GAS-FLAMED ROTISSERIE OVEN MODEL HGFR ML-132078 Natural Gas ML-132079 Propane Gas MODEL HGFR.
– 2 – © HOBART CORPORATION 2002, 2005 IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
– 3 – CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation and Care of HGFR GAS-FLAMED ROTISSERIE OVEN SA VE THESE INSTRUCTIONS GENERAL The model HGFR Series Gas-Flamed Rotisserie Oven features stainless steel interior and exterior for ease of cleaning. Infrared ceramic gas burners efficiently roast the product.
– 5 – INST ALLA TION Prior to installation, verify that the electrical service and gas supply (natural or propane) agree with the specifications on the machine data plate located on the right side of the rotisserie oven. LOCATION WARNING : THE ROTISSERIE OVEN SHOULD NOT BE ACCESSIBLE TO THE CUSTOMER; HOT GLASS AND PARTS CAN CAUSE BURNS.
– 6 – ASSEMBLY Carefully remove and inspect all loose parts packed with the rotisserie oven, including the following: Overflow Tube (1) Skim Tube (1) Ceramic Logs (4) Removable Rear Panel (1) Door Handle Knobs (2) Wire Rack (1) Unwrap foot pedal switch and place on floor.
– 7 – Fig. 6 LEVELING If the rotisserie oven is equipped with casters (standard), move the rotisserie oven to its final installed position and lock the front casters; back casters are nonlocking. Casters are nonadjustable; therefore, the floor must be level to avoid experiencing cooking problems.
– 8 – GAS CONNECTION All gas supply connections and any pipe joint compound must be resistant to the action of propane gas. Codes require that a gas shutoff valve be installed in the gas line ahead of the rotisserie oven; use the valve provided. A gas pressure regulator is supplied with the rotisserie oven.
– 9 – OPERA TION WARNING : HOT GLASS, GREASE AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE ROTISSERIE. Fig. 10 Foot switch (Fig.
– 10 – SET UP ROTISSERIE OVEN • Cover center shaft in the rotisserie oven with aluminum foil. CAUTION: Do not spray gas burners, ignitors or lights with nonstick product. • Spray noncooking components such as the interior walls, drum surfaces and wire rack with a nonstick product (Figs.
– 11 – PREHEA TING • Controller displays rdy . • Turn Lights switch on (Fig. 15). • Turn Motor switch on (Fig. 15). • Turn Show Burner switch on (Fig. 15). • Check to see that Show Burner is lit. • If Burner does not ignite, turn Show Burner switch off then on again.
– 12 – • Bring tie to front, holding the wings to the side of the chicken (Fig. 18). • Insert angle spit (V) neck first (Fig. 19). PL-41696 PL-41697 Fig. 18 Fig. 19 • The flat side of spit must be parallel with breast bone (Fig. 20). • Make sure that the legs and thighs are on the same side as breasts (Fig.
– 13 – LOADING • Insert pointed end of the angle spits into left side of rotor, facing the unit (Fig. 24). CAUTION: Do not jam angle spit into the square hub. • Insert square end of the angle spit in the square hub on the right side of the rotor (Fig.
– 14 – MANUAL COOKING In manual mode Cook Time, Cook Temp and Hold Temp settings are saved in short-term memory only and should be verified each time a manual process begins. Controller cycles top burners on and off. When cooking partial loads or when cooking special glazes, cook with one burner on or with a lower Cook Temp setting.
– 15 – PROGRAMMED COOKING In programmed mode, preprogrammed recipes stored in long-term memory are used. Controller cycles top burners on and off. When cooking partial loads or when cooking special glazes, cook with one burner on or with a lower Cook Temp setting.
– 16 – T welve recipes, shown below , are preprogrammed at the factory . The table provides an extra space for each recipe so you can pencil in your own settings if you choose to reprogram a recipe.
– 17 – Fig. 32 Selecting the Recipe • Controller displays rdy . • Press . The last operated program displays, for example: r01 . • Press the up or down keys until the desired recipe number is displayed. For example: r03 . • Press and together to enter program mode.
– 18 – Fig. 33 UNLOADING WARNING : PRODUCT WILL BE HOT WHEN UNLOADING ACCESSORIES. USE CARE WHEN UNLOADING THE ROTISSERIE OVEN. • Stop hold cycle, open door and begin unloading. • Step on and hold down the foot switch to stop rotor. • Use a thermometer to check product for doneness (popper can also be an indicator of doneness).
– 19 – • Add water to the drip pan until the grease has flowed into the skim tube and down through the drain connection. – For systems plumbed to water line, turn water valve knob on until grease is removed from the drip pan, then turn water valve off (Fig.
– 20 – PL-41657-1 CERAMIC LOGS Fig. 38 CAUTION: Excessive water and harsh cleaners will damage control panel. • Clean the control panel with a sponge or clean, soft cloth. • Clean the exterior of the rotisserie oven with warm, soapy water and a soft cloth or sponge.
– 21 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY BEFORE PERFORMING ANY MAINTENANCE. WARNING : HOT GLASS, GREASE AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE ROTISSERIE OVEN. Light bulbs require replacement periodically.
– 22 – TROUBLESHOOTING Problem Possible Cause Display not illuminated. Rotisserie oven not plugged in. Top burner(s) will not 1. Temperature and burner switch(es) not on. ignite. 2. Controller Cook Temp not set to 600 ° F (max.). 3. Main gas valve not open.
– 23 – NOTES.
– 24 – FORM 35504 Rev. A (Mar. 2005) PRINTED IN U.S.A. NOTES.
デバイスHobart HGFR ML-132079の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart HGFR ML-132079をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart HGFR ML-132079の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart HGFR ML-132079の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart HGFR ML-132079で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart HGFR ML-132079を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart HGFR ML-132079の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart HGFR ML-132079に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart HGFR ML-132079デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
