HobartメーカーML-132183の使用説明書/サービス説明書
ページ先へ移動 of 20
701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 34622 Rev. B (Sep. 2003) HO210 SERIES RA CK O VENS WITH ELECTR ONIC O VEN CONTR OL MODEL HO210E1 (ELECTRIC) ML-132180 HO2.
IMPORT ANT FOR Y OUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
– 3 – MODEL HO210G1.
– 4 – TABLE OF CONTENTS GENERAL ............................................................................................................................................. 5 INSTALLATION ..........................................................
– 5 – OPERA TION AND CARE OF MODELS HO210G1/HO210G2 GAS RA CK O VENS and HO210E1/HO210E2 ELECTRIC RA CK O VENS KEEP THIS MANU AL FOR FUTURE USE GENERAL Models HO210G1/HO210G2 (gas) and HO210E1/HO210E2 (electric) Rack Ovens accommodate roll-in racks.
– 6 – OPERA TION WARNING: THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING OR CLEANING THE OVEN. CONTROLS PL-53621 SET TEMP.
– 7 – CONTROL GUIDE Y E K N O I T C A Y A L P S I D . P M E T . e r u t a r e p m e t d e r i s e d e h t t e s o t s s e r P . d a p y e k r e b m u n e h t g n i s u e u l a v e h t r e t n E t e s e h t s y a l p s i d w o d n i w . P M E T T E S e b l l i w t h g i l N O T A E H e h T .
– 8 – PL-53621 SET TEMP. OVEN TEMP. Actual Temperature In Oven Max.Temp. 525 F / 274 C HEAT ON O O TIMER STEAM DELAY (AIRFLOW) ON Seconds ON Minutes Minutes Set Remaining Heat is disabled during this delay ON QUICK SET Number 0-84 TEMP.
– 9 – BASIC OPERATION WARNING: THE OVEN AND ITS PARTS ARE HOT. TO PREVENT BURNS, USE HOT PADS OR PROTECTIVE MITTS WHEN LOADING OR UNLOADING THE OVEN. 1 . Preheat the oven. 2 . Confirm that the door is closed. This enables the rack carrier to lift and rotate.
– 10 – PROGRAMMING THE QUICK SET MENU QUICK SET stores up to 84 programs that can be stored in memory and recalled by number when needed. A program is a set of baking instructions - TEMP., TIMER, STEAM and DELAY settings - that the operator defines for any baking operation.
– 11 – Changing Quick Set Programs 1 . When the power is turned on, the oven defaults to QUICK SET-1. 2 . Press TEMP. and enter 99 on the number keypad. Repeat this step for TIMER, STEAM and DELAY. 3 . Wait for displays to change to 0. 4 . Press TEMP.
– 12 – TEMPERATURE AND TIMER CONTROL SETTINGS The temperature and timer controls are factory set to degrees Fahrenheit with minutes set and minutes remaining. If desired, the controls can be changed to degrees Celsius and/or hours and minutes remaining as follows: 1 .
– 13 – SHUTDOWN 1 . Remove all remaining product. 2 . Press TEMP. to shut off heat. 3 . Allow the oven to cool and then turn the power switch to the OFF position. 4 . Clean the baking chamber. (See CLEANING.) 5 . For lengthy shutdowns, shut off main power, gas and water supplies.
– 14 – MAINTENANCE WARNING : THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING OR CLEANING THE OVEN. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. GENERAL As Needed • Inspect the area around the oven.
– 15 – O WNER PREVENTIVE MAINTENANCE PR OCEDURE INTRODUCTION This customer preventive maintenance (PM) section includes procedures to inspect for proper operation and cleaning of components. Owner Preventive Maintenance Procedures are written for gas ovens.
– 16 – Clean and Vacuum Components and Control/Burner Compartment Areas 1 . Clean the control/burner compartment area (Fig. 3) of dust and/or lint accumulation.
– 17 – Inspect Door Components 1 . Check loading door latch. A. Check door gasket for good condition. If door gasket needs replacement, contact your local Hobart office for service. B. Check loading door latch (Fig. 5), latch must fully extend when door is closed and contacting door gasket.
– 18 – Inspect Air Louvers 1 . Check air louvers (shutters) (Fig. 9) inside oven and tighten any loose screws. 2 . Check oven interior, tighten or replace loose or missing panel screws. Also check floor anchors. Fig. 9 Inspect Cavity Vent 1 . Check vent for proper operation.
– 19 – Verify Ignition Module Safety Lockout Functions (Gas Ovens) 1 . Verify ignition module safety lockout functions. A. Turn the oven ON and close the door. B. Set the oven control to call for heat, make sure convection fan is running and the burner has established a flame.
– 20 – D E D E E N S A Y P O C S R E B M U N L A I R E S / L E D O M R E N W O D E D N E M M O C E R T S I L K C E H C E C N A N E T N I A M E V I T N E V E R P S A G - S N E V O K C A R Y R E K A B L L A C N.
デバイスHobart ML-132183の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hobart ML-132183をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart ML-132183の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart ML-132183の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart ML-132183で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart ML-132183を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart ML-132183の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart ML-132183に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart ML-132183デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。