Hobart Welding ProductsメーカーHSW 25の使用説明書/サービス説明書
ページ先へ移動 of 24
Visit our website at www.HobartWelders.com Processes OM-715 189 193E October 2003 Resistance Spot W elding Description HSW 15 And HSW 25.
Hobart W elders manufactures a full line of welders and welding related equipment. For information on other quality Hobart products, contact your local Hobart distributor to receive the latest full line catalog or individual catalog sheets. T o locate your nearest distributor or service agency call 1-877-Hobart1.
T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
OM-715 Page 1 Return T o T able Of Contents SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING spotom _nd_8/03 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols.
OM-715 Page 2 Return T o T able Of Contents The tong tips, tongs, and linkages move during operation. MOVING P ARTS can cause injury . D Keep away from moving parts. D Keep away from pinch points. D Do not put hands between tips. D Keep all guards and panels securely in place.
OM-715 Page 3 Revenez à la table des matières SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION spot_fre 8/03 2-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette procédure présente des risques de danger ! Ceux-ci sont identifiés par des symboles adjacents aux directives.
OM-715 Page 4 Revenez à la table des matières DES ORGANES MOBILES peuvent provoquer des blessures. Pendant le soudage, les bras et électrodes se déplacent. D Ne pas s’approcher des organes mobiles. D Ne pas s’approcher des points de coincement.
OM-715 Page 5 Return T o T able Of Contents SECTION 3 − INTRODUCTION 3-1. Specifications Model AC Input V oltage 50/60 Hz W ork Capacity Combined Thickness Rated Output At 50% Duty W elder Dimensions W eight Model V oltage 50/60 Hz 1-Phase Combined Thickness Mild Steel Output At 50% Duty Cycle* Height Width Length HSW 15, RSP 1 10 11 0 1/8 in (3.
OM-715 Page 6 Return T o T able Of Contents B. Dressing The Tips 1 New T ip 2 Used Tip Requiring Dressing 3 Dressing Method − Keep top diameter same as a new tip. 1 T ools Needed: d = <1/8 in (3.2 mm) diameter for 1.5 kV A models; 5/32 in (4 mm) for 2.
OM-715 Page 7 Return T o T able Of Contents 4-2. Installing Or Cleaning T ongs ST-800 155-A / Ref. ST -800 154-A Y T ur n off and unplug welder . . Be sure tong ends are clean and not corroded before installing.
OM-715 Page 8 Return T o T able Of Contents 4-3. Adjusting T ong And Hand Lever Pressure Y T ur n off and unplug welder . Y Excessive tong pressure can dam- ag e tips.
OM-715 Page 9 Return T o T able Of Contents 4-4. Installing Handle Y T ur n off and unplug welder . 1 Wodden Handle 2 Handle Bolt 3 Brackets (15, 15T Models Only) Install handle onto the spot welder as shown above. For 25 and 25T Models, install han- dl e onto either side as desired for either right- hand or left-hand use.
OM-715 Page 10 Return T o T able Of Contents 4-5. Connecting Input Power Ref. ST-800 156 Y Input power supply wiring and receptacle must meet National Ele c t r i c a l C o d e a n d all other code requirements. Operate spot welder from a sepa- rately fused or circuit breaker pro- tected circuit, and use correct size input conductors.
OM-715 Page 1 1 Return T o T able Of Contents SECTION 6 − MAINTENANCE AND TROUBLESHOOTING 6-1. Routine Maintenance Y Disconnect power before maintaining. Every Use 3 Months 6 Months Inspect T ips Replace Unreadable Labels Blow Of f Or V acuum Unit During Heavy Service, Clean Monthly OR 6-2.
OM-715 Page 12 Return T o T able Of Contents SECTION 7 − ELECTRICAL DIAGRAMS SA-162 467-B Figure 7-1. Circuit Diagram For 1 10 And 220 V olt Models.
OM-715 Page 13 Return T o T able Of Contents Notes.
OM-715 Page 14 Return T o T able Of Contents SECTION 8 − P ARTS LIST ST-145 048-D . Hardware is common and not available unless listed. 31 30 28 27 29 42 46 32 37 36 45 Figure 8-1.
OM-715 Page 15 Return T o T able Of Contents 15,1 10 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Main Assembly Model Quantity 25, 220 1 019 643 HANDLE, carrying 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-715 Page 16 Return T o T able Of Contents Replace Coils At Factory Or Factory Authorized Service Station Description Part No. Item No. Figure 8-2. T ransformer , Power Main (Fig 8-1 Item 37) Model 15,1 10 25, 220 095 345 095 354 Quantity 1 026 601 INSULA TION 1 .
OM-715 Page 17 Return T o T able Of Contents Figure 8-3. Spot Welder T ongs And Tips Flat Flat (89 mm) (89 mm) 6-1/2” (165 mm) 3-1/2” 3-1/2” Standard Flat 205 552 205 553 MO Of fset 205 557 Stan.
9/93 OPTIONS AND ACCESSORIES SWP-2 SPOT WELDER PEDEST AL (#205 567) Leaves hands free to handle the work. When foot control is depressed, tongs close and Start Switch is activated. SPOT WELD TIMER (#205 569) HSW 15 (#205 570) HSW 25 Cannot be used on “T” model units.
Warranty Questions? Call 1-877-HOBART1 for your local Hobart distributor. hobart retail 8/03 Service Y o u always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor or call 1-800-332-3281.
PRINTED IN USA 2003 Hobart Welding Products. 1/03 Hoba rt W elding Produc ts An I l li noi s T ool Works Com pany 600 W es t Main St reet Troy , OH 45373 USA For T ech nical Assistance: Call1-800-.
デバイスHobart Welding Products HSW 25の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart Welding Products HSW 25をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart Welding Products HSW 25の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart Welding Products HSW 25の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart Welding Products HSW 25で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart Welding Products HSW 25を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart Welding Products HSW 25の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart Welding Products HSW 25に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart Welding Products HSW 25デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
