HomeliteメーカーUT10530Aの使用説明書/サービス説明書
ページ先へ移動 of 36
OPERA T OR'S MANU AL 16 in. (406 mm) 33cc Chain Saw UT10530, UT10530A, UT10947D , UT10947E Y our new chain saw has been engineered and manufactured to Homelite’ s high standard for dependability , ease of operation, and operator safety . Properly cared for , it will give you years of rugged, trouble-free performance.
Page 2 Introduction ..................................................................................................................................................................... 2 General Safety Rules ..................................
Page 3 W ARNING: The warnings, labels, and instructions found in this section of the operator's manual are for your safety. Failure to follow all instructions may result in serious personal injury. Safe operation of this tool requires that you read and understand this operator's manual and all labels affixed to the tool.
Page 4 W ARNING: The warnings, labels, and instructions found in this section of the operator's manual are for your safety. Failure to follow all instructions may result in serious personal injury. GENERAL PRECAUTIONS DO NOT CUT VINES and/or small underbrush (less than 3 in.
Page 5 PULL PUSH Fig. 1 PUSH AND PULL The reaction force is always opposite to the direction the chain is moving. Thus, the operator must be ready to control the PULL when cutting on the bottom edge of the bar and the PUSH when cutting along the top edge.
Page 6 Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION Indicates danger, warning or caution.
Page 7 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
Page 8.
Page 9.
Page 10.
Page 11.
Page 12.
Page 13 Fig. 18 THROTTLE TRIGGER THROTTLE LOCK BUTTON TRIGGER RELEASE OPERA TION 7 . While squeezing both the trigger release and throttle trigger, push in the throttle lock button. Release the throttle trigger. This latches the trigger for starting. 8 .
Page 14.
Page 15 BASIC OPERATING/CUTTING PROCEDURES Practice cutting a few small logs using the following technique to get the “feel” of using your saw before you begin a major sawing operation. 1. T ake the proper st ance in front of the wood with the saw idling.
Page 16 W ARNING: Weather conditions and altitude may affect carbure- tion. Do not allow bystanders close to the chain saw while adjusting the carburetor. ADJUSTING IDLE SPEED See Figure 26. If the engine starts, runs, and accelerates but will not idle, turn the idle speed screw “ T ” clockwise to increase idle speed.
Page 17 OPERA TION Fig. 27 45° 45° 90° 135° 135° 90° 135° FROM PLANNED LINE OF FALL PATH OF SAFE RETREAT PLANNED LINE OF FALL PLANNED LINE OF FALL PATH OF SAFE RETREAT PROPER PROCEDURE FOR TREE FELLING See Figures 27 through 30. 1. Pick your escape route (or routes in case the in- tended route is blocked).
Page 18 Note: Never cut through to the notch. Always leave a band of wood between the notch and back cut (approxi- mately 2 inches (5 cm) or 1/10 the diameter of the tree). This is called "hinge" or "hingewood". It controls the fall of the tree and prevents slipping or twisting or shoot- back of the tree off the stump.
Page 19 REMOVING BUTTRESS ROOTS See Figure 31. A buttress root is a large root extending from the trunk of the tree above the ground. Remove large buttress roots prior to felling. Make the horizontal cut into the buttress first, followed by the vertical cut.
Page 20.
Page 21 LIMBING AND PRUNING See Figure 36. Work slowly, keeping both hands on the saw with a firm grip. Maintain secure footing and balance. Keep the tree between you and the chain while limbing. Do not cut from a ladder, this is extremely dangerous.
Page 22 ASSEMBLING THE BAR AND CHAIN See Figures 38 through 48. D ANGER: Never start the engine before installing the guide bar, chain, drivecase cover, and clutch drum. Without all these parts in place, the clutch can fly off or explode exposing the user to possible serious injury.
Page 23.
Page 24 11. Replace the outer guide bar plate ensuring that the bar pin groove is at the bottom with the upper and lower edges angled away from the guide bar. 12. Replace the clutch cover and bar mounting nuts. 13. Tighten the bar mounting nuts finger tight only.
Page 25 ADJUSTING THE CHAIN TENSION See Figures 49 through 51. W ARNING: Never touch or adjust the chain while the motor is running. The saw chain is very sharp. Always wear protective gloves when performing maintenance on the chain. 1. Stop the engine before setting the chain tension.
Page 26.
Page 27.
Page 28 TOP PLATE FILING ANGLE See Figure 60. CORRECT 30° - file holders are marked with guide marks to align file properly to produce correct top plate angle. LESS THAN 30° – for cross cutting. MORE THAN 30° – feathered edge dulls quickly.
Page 29 Fig. 65 LUBRICA TING HOLE MAINTAINING THE GUIDE BAR See Figure 65. CA UTION: Make sure the chain has stopped before you do any work on the saw. Every week of use, reverse the guide bar on the saw to distribute the wear for maximum bar life. The bar should be cleaned every day of use and checked for wear and damage.
Page 30.
Page 31.
Page 32.
Page 33 Length of Bar Guide Bar Part Number Chain Part Number 14 in. PS06331 984296005 16 in. PS06338 PS06285 B AR AND CHAIN COMBINA TIONS TROUBLESHOOTING PROBLEM POSSIBLE CA USE SOLUTION Engine will not start. (Make sure Ignition Switch is in start position “I”.
Page 34 Note: The carburetor adjustment needle(s) are equipped with plastic cap(s) that prevent counterclockwise rotation from the original factory adjustment.
Page 35 W ARRANTY CALIFORNIA EMISSION CONTROL LIMITED W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS HOMELITE CONSUMER PR ODUCTS, INC. The U.S. Environmental Protection Agency (EP A), the California Air Resources Board (CARB), and Homelite Consumer Products, Inc.
For product information, technical help, dealer locations or parts ordering information visit our website at: www .homelite.com. HOMELITE CONSUMER PRODUCTS, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Post Office Box 1207, Anderson, SC 29622 Phone 1-800-chainsaw (1-800-242-4672) www.
デバイスHomelite UT10530Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Homelite UT10530Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHomelite UT10530Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Homelite UT10530Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Homelite UT10530Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Homelite UT10530Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHomelite UT10530Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Homelite UT10530Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHomelite UT10530Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。