Hondaメーカー08B21-SJC-102の使用説明書/サービス説明書
ページ先へ移動 of 17
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 1 of 17 INST ALLA TION INSTRUCTIONS Accessory Application Publications No.
2 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 2 EPT sealers 4 Cushion tapes 2 Socket bolts, 4 x 10 mm 3 W asher screws, 4 x 12 mm 2 W asher screws, 4 x 6 mm Re.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 3 of 17 3. Remove the fuel fill door release handle. Remove the left front door sill trim (three clip s and three retaining tabs). 4. Remove the left rear door sill trim (three clip s and four retaining t abs).
4 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 9. Remove the rear seat belt anchor bolt and eight seat anchor bolts. • Seat belt anchor bolt torque: 30 to 35 N·m (22 to 25 lbs) 8. Remove the rear seat bracket covers; • Remove the left and right rear seat bracket covers (two clips for each cover).
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 5 of 17 11. Remove the rear trim panel cover (eight clip s and two retaining t abs). 14 . Remove the left rear lower anchor bolt cover , and remove the left rear seat belt lower anchor bolt.
6 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 17. Remove the rear bumper: • Remove the license plate (two bolts). • Remove two bolts, six self-t apping screws and six clips from the rear bumper . • Pull the rear bumper toward you.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 7 of 17 22 . Remove the left front anchor (two TORX bolts). 21. Remove the left C-pillar outer trim (slide rearward, and unplug the vehicle connector). Remove the clips from the body , and reinstall the clips to the lef t C-pillar outer trim.
8 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 24 . Remove the left bed rail trim: • Remove the screw cover (four retaining t abs). • Remove the self-tapping screw . • Pull the left bed rail trim back to release the six clips, and remove the lef t bed rail trim.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 9 of 17 28 . Remove the tailgate trim: • Remove the four screws and release the one end clip on each side. • Sharply push the tailgate to the right to release the 16 clips from the trim.
10 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 33 . Install one blind nut into each 8 mm hole. 34 . Remove the four screws from the rear camera. Route the rear camera harness through the rear camera subbracket, and install the rear camera subbracket to the rear camera with the four screws.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 11 of 17 36. Route the rear camera harness through the 10 mm hole in the tailgate, and seat the grommet into the 10 mm hole. 38 . Align the two locating tabs on the rear camera subbracket with the slots in the rear camera bracket, and install two 4 x 6 mm washer-screws.
12 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 40. Route the rear camera harness along the tailgate as shown. 41 . Remove the TORX bolt from the tailgate hinge, and attach the harness clamp bracket B to the tailgate using the TORX bolt you just removed.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 13 of 17 42. Secure the rear camera harness to the harness clamp bracket B with three small wire ties.
14 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 51. Route the rear camera harness out through the bed panel hole, and secure the rear camera harness to the vehicle harness with one wire tie just inside the panel hole.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 15 of 17 53. Remove the vehicle grommet from the left C-pillar . 54. Insert the rear camera harness through the grommet, and route the rear camera harness through the vehicle grommet opening.
16 of 17 AII 36587 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved. 63 . Slide the driver’s seat back and forth to check that the rear camera subharness is not pulled too tight or is too loose. 62. Plug the rear camera subharness 6-pin connector into the Navi control unit.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36587 (0705) 17 of 17 64 . Reconnect the negative cable to the battery . T urn the key to the ON (II) position, and enter the Navi code. 65 . Move the shift knob to the “R” position.
デバイスHonda 08B21-SJC-102の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Honda 08B21-SJC-102をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHonda 08B21-SJC-102の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honda 08B21-SJC-102の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honda 08B21-SJC-102で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honda 08B21-SJC-102を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHonda 08B21-SJC-102の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honda 08B21-SJC-102に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHonda 08B21-SJC-102デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
