Honda Power EquipmentメーカーK Seriesの使用説明書/サービス説明書
ページ先へ移動 of 17
MTK Kit: Honda K Series Engine Conversions for Classic Minis MTK Installation Manual For Classic Minis 1959 – 2001.
2 Dear Customer, We welcome you to the Honda Powe red Mini Worl d. Thank you and Congratulations for your purc hase. You can be certain th at you have made a wise choice with this upgrade. Th is kit was designed to help put you on the right track when building your ultimate Mini.
MTK Contents This Section contains a list an d description of the parts in cluded in the MTK Kit, and a list of parts that you will need in addition to the MTK Kit.
4 Additional Parts Needed: - Honda K series engine/transmissi on (See List on pages 15 and 16) - Coil-over shocks (#511200) - Front disc brake system such as; Mini Tec’s Superbrakes, Mini 8.
Preparation Step 1: Remove stock Mini engine and s ubframe from Mini. Then remove everything else in the engine compartment. Step 2: Whether you use Mini Tec’s MT Flip Front End Kit or yo u do an extension yourself, you will need to cu t existing Mini front end after the a-panel seem to remove existing Mini front.
Step 3: Clean, Prepare, and Prime t he cars fi rewall and all ruff surfaces (See Figure 1-3). Note: Add additional meta l for extra stiffness to the fr ont side of the a-panel as shown in the photo below. A gu ide tab on the inside of th e a-panel will help align the MT Flip Front End as it closes.
Step 3: Cut out metal just below stock shock mount. This is needed to fit the MTK subframe (See following two photos). Your Mini should now be prepared for the i nstallation proces s.
Subframe assembly *Suppli e d wi t h ki t Step 1: Attach upper bump stops. Mini bump stops with the single stud will work here. Step 2: Attach the subframe to the car usin g the two large subf rame mounting bolts just like the standard Mini subframe.
Step 3: Drill six holes to support the botto m of the subframe using a 5/16” drill bit. Use the six supplied 5/16” bolts with plates to fa sten the subframe to the car on the lower side. The plates will go inside of the car to give the floor panel extra support.
Installing Engine into Subframe: Step 1: Drill stock B Series Honda engine and transmission mounts to ½”. Step 2: Attach supplied transmission mount adaptor plate using the supplied hardware in the sequen ce that it is attached to th e plate. Then attach Honda B Series transmission mount to transmission.
Step 5: Lower engine into subframe and a ttach it with the ha rdware provided. Step 6: Connect rear engi ne stabili zer to transmission as it is aligned on frame.
Axles: Assembly and Installation Parts needed for Ass embly: *Chromol y Axle Shafts, Complet e Inner Honda CV Joint Assemblies, and Comp lete Outer Mini CV Joint Assemblies. (See Photo Below) Step 1: Assemble Small end of axle shaft with the Mini cv joint assembly as done on a stock Mini but replace ball beari ng gear with supplied gear.
Honda Axle End Assembly: Assemble large splinned side of axle with the Honda cv joint assembly. (See followi ng four Photos ) 13.
Axle Installation: Simply slide one of the axles in to the tran smission and the other into the engine mid-shaft until the axles lock into place. Swivel Hubs and Brakes: Install the Swivel Hubs an d Brakes as done on stock Mini . Replace Mini steering ar m with the *Extended Steering Arm.
Step 2: Attach top shock t o upper strut mount. See Photo. Fuel System: Change your fuel pump to one that ranges from 32 to 48 PSI. A return line will be needed on certain models th at do not have them. An inline fuel pressure regulator will al so be required to set your system at 45psi.
16 Torque: 149 ft·lbf ( 202 N·m) @ 7000 rpm Redline: 8400 rpm o 2001-2006 Honda Integra Type-R (DC5) Displacement: 1998 cc Compression: 11.
17 - Front Camber Setting = -0.5 to -1 Degree (Less for street driving , more for racing) Check List: For your safety, please check… - That every su sp ension component is fastened tightly. - That the steering system is fastened properly and all nuts and bolts are secure.
デバイスHonda Power Equipment K Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Honda Power Equipment K Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHonda Power Equipment K Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honda Power Equipment K Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honda Power Equipment K Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honda Power Equipment K Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHonda Power Equipment K Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honda Power Equipment K Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHonda Power Equipment K Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。