HoneywellメーカーIPGSM-DPの使用説明書/サービス説明書
ページ先へ移動 of 16
I I P P G G S S M M - - D D P P C C o o m m m m e e r r c c i i a a l l F F i i r r e e C C o o m m m m u u n n i i c c a a t t o o r r I I n n s s t t a a l l l l a a t t i i o o n n a a n n d d S S e e t t u u p p G G u u i i d d e e IPGSM-DP Commercial Fire Comm unicator RADIO TROUBLE LO W BA TT AC ON AC LOSS 800-08074 1/11 Rev.
Contents General Info rmation ............................................................................................................ ...........1 Package Contents ..................................................................................
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 1 – General Information The IPGSM-DP Commercial Fire Comm unicator (henceforth referred to as IPGSM-DP) includes everythin.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 2 – STEP 1 – Activate the SIM and Setup the Customer Account The communicator requires a subscriber account (customer account) to be setup with Alar mNet Direct. This is accomplished by registering th e communicator' s iGSM communications m odule with AlarmNet.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 3 – STEP 3 – Determine the Signal Strength and Select a Location IMPORTANT - Do Not mount this de vice outdoors.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 4 – 3. Install the two plastic m ounting rails for th e LED Display board. Th ey simply snap into the back plate holes. 4. Connect the LED Dis play board to its connect or, then slide the board int o the mounting rails.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 5 – IPGSM-DP-001-V2[US Only] TB 1 6 7 8 5 10 11 9 2 3 4 1 FOR EXTERNAL ANTENNA 50 OHM MMCX ONLY PRIMARY POWER: 9 - 16.5 VAC CURRENT: 900mA PEAK, 70mA STANDBY BATTERY: 8V. 3.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 6 – STEP 5 – Program the Communications Module You must use the 7720P Programming tool to program the IPGSM-DP. When using the 7720P P rogramming tool, the valu es given below are for mo st installations.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 7 – To exit the progr amming mode, press [ N] in response to the "Review?" pr ompt. Then press [Y] to the "Exit Prog Mode?" prompt. Upon exiting, the ro ot file is updated to log the changes made.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 8 – IPGSM-DP Trouble Detection Information Telco 1 is used for th e Fire Panel to output con tact ID messages to the IPGSM-DP, an d Telco 2 is use d by the IPGSM-DP to report f aults to the Fire P anel.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 9 – Note: If a wire pulled out of the LED Board Connector refer to the diagram on right and reinsert wir e, ensuring the connector pin is locked in. PowerBoost1 Module Information LED Indicator STATUS AC (green) AC power available.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 10 – iGSM Communications Module Information TB 1 6 7 8 5 10 11 9 2 3 4 1 PRIMARY POWER: 9 - 16.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 11 – RF Specifications Band Transmission Frequency (MHz) Transmit Power (dBm) Receive Frequency (MHz) Receive Sensitivity .
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 12 – NOTES.
Wiring Diagram The wiring diagram below is depict ed for point-to-point electrical con nection checks used for tr oubleshootin g or componen t replacement. It is not in tended to show the phys ical routing of wires. When replacing a wire or componen t, ensure the wire is route d in the same manner as the orig inal factory wire.
FCC STATEMENT Note: This equipment has been tested and foun d to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits ar e designed to prov ide reasonable prot ection against harmful interference when the equipment is operated in a commerci al environment.
デバイスHoneywell IPGSM-DPの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Honeywell IPGSM-DPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoneywell IPGSM-DPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honeywell IPGSM-DPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honeywell IPGSM-DPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honeywell IPGSM-DPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoneywell IPGSM-DPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honeywell IPGSM-DPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoneywell IPGSM-DPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。