HoneywellメーカーP520の使用説明書/サービス説明書
ページ先へ移動 of 16
USER MANU AL Put Bar Code Here 66-2066-01 P520 Signal Pr ocessor APPLICATION The Hone ywell P520 is a rac k mounting signal proc essor that is compatible with viewing heads in the S5XX and S55XB/BE series. These include models S506, S509 , S511 and S512 , and the advanced viewing head seri es models S550B/BE, S552B/BE and S556B/BE.
P520 SIGNAL PROCESSOR 66-2066—0 1 2 Fig. 1. P520 front faceplate dim ensions. Fig. 2. P520 side view dimensions. INSTALLATION When Installing this Product… 1. Read these instr uctions carefully . F ailure to follo w them could damage the pro duct or cause a hazardo us condition.
P520 SIGNAL PROCESSOR 3 66-2066—01 3. Install a ground wire from the igni tion transformer case to the igniter assembly . 4. Ensure all igniter wires and cables show no signs of wear . Replace any igniter cab les or wires that are fra yed or crac ked.
P520 SIGNAL PROCESSOR 66-2066—0 1 4 Fig. 3. Rear PCB terminal wiring. P olar ity must be observed when wiri ng this connection (the positive terminal is o n the top). This is an is olated input, so two wires are required. Any DC voltage from 7.5 to 30 may be used.
P520 SIGNAL PROCESSOR 5 66-2066—01 Wiring the Vie wing Head Wiring of the viewing head is made to the ter minals on the rear backplane PCB. These termina ls are described as follows: Fig.
P520 SIGNAL PROCESSOR 66-2066—0 1 6 IMPORTANT Source impedance resistor required at the si gnal processor between SC and SIG GND ter minals for proper signal trans- mission. F or resistor value, ref er to the Wir ing of the Viewing Head section. Fig.
P520 SIGNAL PROCESSOR 7 66-2066—01 V erifyin g the v alidity of the ga in code rece iv ed is one o f the tasks performed by the processor in the viewing heads. The self-check pulse from the signal p rocessors is a 100ms-wide, 20V to 24V pulse with two notche s or breaks in it.
P520 SIGNAL PROCESSOR 66-2066—0 1 8 change the display ed value. Once the desired value is display ed, press the ST ORE button. When the set point is stored, four dashes are display ed momen tarily , indicating that the new v alue was stored into the EEPROM.
P520 SIGNAL PROCESSOR 9 66-2066—01 SETUP AND ADJUSTMENT PR OCEDURES Sighting Adjustment Bef ore making definitiv e settings (i.e., estab lishing the set points) for FLAME ON/OFF , the us er must f irst opti mize the sighting of the viewing head.
P520 SIGNAL PROCESSOR 66-2066—0 1 10 TR OUBLESHOO TING Module Comm unications The P520 communicates with any host computer that has a USB por t and suppor ts ASCII character code transmission at 4800 baud (or , in current revisions of the processor chip, at 4800 or 9600 ba ud).
P520 SIGNAL PROCESSOR 11 66-2066—01 T o change or check the station number of the P520, proceed as f ollows: 1. Press and hold th e Reset button for 4 seconds. 2. The 4 LED digits will show the baud rate and the station number . The 2 leftmost digits are the baud rate (96 or 48); the 2 righ tmost digits are station number fro m (0 to 63).
P520 SIGNAL PROCESSOR 66-2066—0 1 12 address 2). T o change to 9600 baud, in crease the display past 4863. The ne xt display will be 9600, which is 9600 baud, address 0. Then increase the display fur ther to the desired address. T o retur n to 4800 ba ud, reduce the display below 9600, and set the desired address.
P520 SIGNAL PROCESSOR 13 66-2066—01 Fig. 8. P520 with S550B/BE programming flowchart. PRESS BOT H A & B BU TTO N S “CAL ? ” CALI BR ATE VI EW ING HEAD? N N “CAL U” AUTO ADJ UST UV GAIN? .
P520 SIGNAL PROCESSOR 66-2066—0 1 14 Fig. 9. P520 with S552B/BE programming flowchar t. PRESS BOT H A & B BU TTO N S “CAL ?” CALI BR ATE VI EW ING HEAD? N N NO RMAL O PERA TIO N Y CA LI B R .
P520 SIGNAL PROCESSOR 15 66-2066—01 Fig. 10. P520 with S556B/ BE programming flo wchar t. PRESS BOT H A & B BU TTO N S “CAL ?” CALI BR ATE VI EW ING HEAD? N N “CAL U” AUT O A DJUST UV GA.
P520 SIGNAL PROCESSOR Automation and Co ntrol Solutions Honeywell Internationa l Inc. 1985 Douglas Drive North Golden Valley, MN 55422 customer.honeywell.
デバイスHoneywell P520の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Honeywell P520をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoneywell P520の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honeywell P520の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honeywell P520で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honeywell P520を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoneywell P520の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honeywell P520に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoneywell P520デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。