HoneywellメーカーT775Jの使用説明書/サービス説明書
ページ先へ移動 of 20
PRODUCT DA T A Copyright © 1995 Honeywell Inc. • All Rights Reserved T775J Electronic Remote T emperature Controller FEA TURES • T775 model pro vides reset control with tw o temperature inputs an.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 2 SPECIFICA TIONS IMPORT ANT The specifications given in this publication do not include normal manufacturing tolerances. Therefore, an individual unit may not exactly match the listed specifications.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 3 Mounting: Mounts on any suitable horizontal or vertical surface. (See Fig. 5 for mounting hole locations.) Dimensions: See Fig. 1. Display Resolution: Sensed temperature and other operating parameters are displayed via a liquid crystal display (LCD) with a resolution of 1 ° F or 1 ° C.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 4 Mounting Sensor in T7047C1090 Case 쐃 Run wires from T775J through wall. 쐇 Mount case to wall with screws provided. 쐋 Connect wires from the T775J to two T terminals on the T7047C Case.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 5 Fig. 5. Feature locations. IMPORT ANT Erratic temperature readings from the 193987GA Sensor can be caused by poor wiring practices that must be avoided to assure proper operation: a. Do not route temperature sensor wiring with building power wiring.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 6 SELECT SET ENTER NO COM NC OUTPUT 1 OUTPUT 2 NO COM NC 120V COM 240V 1 2 3 4 SA SB 1 23 1 2 3 4 5 67 8 SA TOD 24V SB C/F M8113 SENSOR A 240 VAC SENSOR B LOAD 1 LOAD 2 BLK RED Fig. 7. Reset control with 24 V ac input, 24 V ac loads.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 7 SELECT SET ENTER OUTPUT 2 NO COM NC 120V COM 240V 1 2 3 4 SA SB 1 23 1 2 3 4 5 67 8 SA TOD 24V SB C/F M8115A SENSOR A 24 VAC SENSOR B LOAD 1 T1 T2 BR W 1 1 POWER INPUT USE SEPARATE TRANSFORMER FOR T775 WHEN POWERING FROM 24 VOLTS.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 8 Fig. 14. Reset control with Series 90 Modutr ol® Motor . Fig. 13. Reset control with 240 V ac input, 240 V ac and 0 to 18 Vdc loads.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 9 Use shielded cable if any of the above conditions cannot be avoided. Device Setup 쐃 Determine the loads to be controlled and the operating mode (heat or cool) and enter on the worksheet.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 10 쐄 Determine the desired Reset Direction (up or down) and enter on the Device Programming Worksheet. This will determine if the setpoint for the control Sensor A will be reset up or down.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 11 쐎 Press Enter to enter the displayed value into memory . 쐅 Press Select four times to return to stage 1 parameters. Scroll through the programming loop a second time to confirm that the appropriate values have been entered into memory .
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 12 SELECT SET ENTER O P E N 1234 38 1 4 17 OPEN CLOSED VOLTAGE SPANS WHEN SWITCH IS DEPRESSED, THE VOLTAGE RANGE IDENTIFIED BY THE VOLTAGE SPAN BELOW THAT SWITCH IS SELECTED. IN THIS CASE, A VOLTAGE SPAN ON 8 VDC HAS BEEN SELECTED.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 13 SENSED TEMPERATURE = 78 o F CALIBRATION SETPOINT 75 o F DEAD BAND DEAD BAND MODULATION HEATING MODE THROTTLING RANGE THROTTLING RANGE * D.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 14 temperature goes down, the control point goes down). The type of ratio is selected by using the two DIP switches provided. The four possible reset operating configurations are illustrated and explained in Fig.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 15 • 4-20 mA: This is a general purpose current mode output that can drive a 600 ohm maximum load without output current 12 3 4 OPEN A C B D 12 3 4 OPEN A C B D 12 3 4 OPEN A C B D 12 3 4 OPEN A C B D A.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 16 degradation. This modulation output can be used with Honeywell Inc Modutrol IV TM Motors that accept an input signal of 4-20 mA or other Honeywell Inc motors with the use of resistor kits.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 17 Display Once power is applied or restored to the device, the display will count down from 210 until the display reads zero, during which time any previously energized outputs will be de- energized.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 18 CHECKOUT After the controller is installed and wired, apply power . Using the programmed control values, verify device operation after completing T able 3. 쐃 As illustrated in the example, record the sensed temperatures for both Sensor A and Sensor B as displayed on the controller .
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 19 Ta b le 3. Check out T able . Checkout Table Checkout Table Example Heat or Cool Load 1 Load 2 Reset Value Load 1 Reset Value Load 2 Heat.
T775J ELECTRONIC REMOTE TEMPERA TURE CONTROLLER 63-2248—4 20 Helping You Control Your World Home and Building Control Honeywell Limited-Honeywell Limitée 740 Ellesmere Road Scarborough, Ontario M1P 2V9 63-2248—4 Rev . 9-95 Printed in U.S.A. www .
デバイスHoneywell T775Jの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Honeywell T775Jをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoneywell T775Jの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honeywell T775Jの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honeywell T775Jで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honeywell T775Jを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoneywell T775Jの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honeywell T775Jに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoneywell T775Jデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
