Hooverメーカー53395の使用説明書/サービス説明書
ページ先へ移動 of 19
Review this manual before operating cleaner.
This cleaner was inspected and packaged carefully before being shipped from the factory. If you should happen to need assistance during assembly or operation, call l-800-944-9200 for automated referral of authorized service outlet locations ( U.S. only ) or l-330-499-9499 to speak with a representative in our Consumer Response Center.
lmwwtant Safeauards! - -m- - - - _----- _- -rl-- -- When using an electrical appliance, always follow basic precautions, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning. injury: n To reduce the risk of fire, electric shock, or Do not use outdoors or on wet surfaces.
Unpacking Unpack cleaner from carton and identify the parts shown. Re- move and dispose of the card- board packing. A. Canister cleaner B. Power nozzle C.
Cleaner description 1. 2. 3. 4. 5. 6. 7. a. 9. Cover: remove by lifting up top section of carrying handle and pulling forward. Carrying handle Check bag indicator: shows red when paper bag should be checked for fullness. Extension wands: use with power nozzle.
Questions or Concerns? The Hoover Company wants to quickly resolve any concerns about your cleaner or questions regarding its use. Look on the list provided with the product for your local Hoover Fact.
Attach second wand to the first. Position cord into cord clips on wands, placing excess cord between nozzle and bottom cord clip. To attach hose to wands, rotate plastic latch ring on hand grip until slots in opening align. Push hand grip onto wand so that button projection fits into slot.
How to use To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
Suction regulator The suction regulator is located on the hand grip and is used to increase or decrease suction for various cleaning tasks. If the power nozzle is difficult to push on some carpet, open the suction regulator. This will prevent damage to the belt.
To connect and remove tools To connect tools, insert end of tool into extension wand and snap into -. position. To disconnect, press down on the center of the spring latch and remove tool. Tools attach to hand grip by rotating plastic ring until slots in the opening align.
How to store Your cleaner can be stored on end as shown in the illustration. Store power nozzle with handle in upright position. The hose and extension wands can be stored disassembled from the cleaner if desired. Maintenance The following sections are concerned with proper maintenance of the cleaner.
How to replace Disconnect cleaner from electrical outlet. 1. Remove cover by lifting top section of carrying handle and pulling forward. 3. Place lower notched edge of new bag collar into grooves located inside front of cleaner. 2. Depress latch and lift out used bag.
Obstructions Remove larger items from carpet and floor surfaces before vacuuming to help prevent obstructions in hose, wands or nozzle connector, and to maintain cleaning effectiveness of your cleaner. There are two conditions that will indicate that an obstruction has occurred: 1.
How to clean Disconnect cleaner from eiectri- cai outlet. The secondary filter is located inside the cleaner behind the paper bag. To remove filter, first remove cover of cleaner, then lift out filter. Clean filter by rinsing it in water. When dry, slide filter back into position.
2. Return nozzle to original position; and lift off nozzle cover. 1 MOTOR PULLEY 3. If the belt is not broken, pull it off the motor pulley. 4. Lift up end of agitator. Remove old belt from agitator pulley and replace with new belt. 5. Stretch belt back and attach to motor pulley.
6. Position nozzle cover on front lip of nozzle base. Press cover into place. Turn nozzle over and replace screws. The agitator When to replace Disconnect cleaner fern eiectri- cai outlet. When agitator brushes are worn, the agitator should be replaced.
Lubrication The motor is equipped with bearings, which have been lubricated for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing.
Service To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: 0 checking the Yellow Page.
0 1/, HOOVER and V# are registered trademarks THE HOOVER COMPANY, NOFiiH CANTON, OHIO 44720 R4 4-96 S3395040/9 I Litho USA 56513-331.
デバイスHoover 53395の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hoover 53395をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoover 53395の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hoover 53395の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hoover 53395で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hoover 53395を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoover 53395の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hoover 53395に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoover 53395デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。