Hooverメーカー53441の使用説明書/サービス説明書
ページ先へ移動 of 20
.
Fill in;and:mWn ! The HOOVER commercial upright cleaner you have just purchased is for carpet and rug cleaning. The cleaning tool attachments are for floor cleaning and above the floor cleaning. Your cleaner is a model . . . . . . . . . . . . . . . . .
ImDortantsa#eauards! I- - -u- - l Read all instructions. l Warning: Electric shock could occur if used outdoors or on wet surfaces. l This cleaner has been equipped with a 3-wire grounding cord in compli- ance with electrical codes devised for your safety.
UNPACKING THE CLEANEd ’ Unpack the cleaner from the carton and identify the parts shown in Fig. 1. cc Remove and dispose of the cardboard 1 1, m-b-- I packing. 1. Upper handle section 2. Lower handle section 3. Cleaner base 4. Cloth bag assembly The cleaner assembled will look like the drawing below.
HOW TO ASSEMBLE A. Attach handle to the cleaner Unscrew nut and remove bolt and plate from handle socket. Place bottom section of handle into handle socket lining up small holes toward front of cleaner. Cord will run up indentation at base of handle, Insert bolt into hole in front of handle.
B. Join upper and lower handles Join upper and lower handles, aligning holes. Place cord clip around cord with flat side toward handle of cleaner and holes to the front. Insert bolt through washer, cord clip and both parts of the handle (small holes).
Upright Handle adjustments The handle has three positions: Up- right for storage and when using attachments. Operating for general operation on carpet and floors. Low for reaching under low furniture. Adjustment for carpet pile height The cleaning of carpet and rugs takes place at the nozzle.
SPECIAL FEATURES Carrying handle Your cleaner has a convenient carrying handle located underneath the handle bail. Edge cleaning This feature improves the cleaning of carpet edges near baseboards and solid furniture. Dust and lint tend tocollect along these edges.
CLEANING TOOL ATTACHMENTS Cleaning tools are available at additional cost from Hoover Dealers. The clean- ing tools allow you to do above the floor cleaning and to clean hard to reach areas.
Grasp the converter; turn red con- verter lock away from the hose. Fig. 5. Bring converter up until it covers the opening. Fig. 7. d Push connector and converter togeth- er and twist. The converter is locked into position when the projections on the converter fit into the holes on the hose connec- tor.
9. Select the proper cleaning tool The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descriptions below. Wall/floor brush* For walls and very irregular hard surface floors such as brick and slate.
. Turn the plastic ring counterclock- wise to lock the tool in place. Fig. 8. For additional length, attach one or both* wands to the vinyl hose as de- scribed above. To attach the tools to the other end of the wand, press down firmly on the white plastic spring latch.
Storing attachments For Storage, the attachment set will conveniently fit in the storage bag.* The bag has two slots located near the top for use in hanging. Therefore, it can be attached to the cleaner or hung conveniently on a hook in the closet. To clean attachments To clean the hose wipe off dirt with a cloth damp- ened with a liquid detergent.
Empty bag by placing large opening over a paper. The bulk of the dirt will fall on the paper. Shake bag until clean. Replace the bag closure clip and at- tach bag to cleaner following the instructions give on page 5.
2. Release worn belt from pulley. 3. Lift out rug agitator, remove old belt and place new belt in groove of rug agitator. 4. Replace agitator. On one end of the agitator roll there is a raised metal plate. Make sure that this end is placed in groove on side of cleaner.
The brushes When to replace brushes When brushes are worn and bristles do not touch the edge of a card held across the bottom plate, they should be replaced. Always replace both brushes at the same time to maintain cleaning effectiveness. What brushes to buy When purchasing new brushes, ask for Hoover Part No.
6. Remove brushes by pulling them from agitator. Slide new brushes into channels. Push them in as far as possible. 7. To reassemble, replace shaft and end assembly lining up the locator with the slot in the agitator. Press into place. Place remaining end sec- tion over the shaft end, lining up the locator and slot.
USER CHECK LIST This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem develops, it usually can be remedied quite easily when the cause is identified. Accordingly, this check list is provided for your convenience.
ENERGY SAVING TIPS 1. Empty cleaner bag promptly, before overfilled. 2. To maintain effective cleaning, replace agitator brushes and belt when necessary.
VCMA VACUUM CLEANER MANUFACTURERS ASSOCIATION (HOOVER -AN ASSOCIATION MEMBER) Service To The Consumer Since 19 13 This information has been compiled by the Vacuum Cleaner Manufacturers Associ- ation from Governmental and Private Sources concerned with product safety.
デバイスHoover 53441の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hoover 53441をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoover 53441の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hoover 53441の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hoover 53441で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hoover 53441を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoover 53441の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hoover 53441に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoover 53441デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。