HooverメーカーS2200の使用説明書/サービス説明書
ページ先へ移動 of 34
Vacuum Cleaner 1 Read this manual before operating cleaner.
Fill in and retain The HOOVER vacuum cleaner you have just purchased is designed for carpet and rug ckaning and has cleaning took for other tasks. The model and serial number are located on the bottom of the cleaner. For your personal records, please en&w the COMPLETE model and serial number in the spaces provided and retain this information.
Important Safeguards! ken using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning. injury: n To reduce the risk of fire, electric shock, or l l l l l l l l l l l l l l l l Do not use outdoors or on wet surfaces.
Unpacking Unpack the cleaner from the carton and identify the parts shown. Remove and dispose of the cardboard packing. A. Upper handle B. Lower handle c. cord D. Tool rack E. Tool rack screw F. Bracket G. Bag compartment H. Cleaner body I. Handle bolt and nut (One extra nut included) J.
/I L-I ROI Note: The white switch look above the ON/OFF switch, on th8 upper handle, holds the switch in the Off position and aids in proper assembly of your cleaner. Assembly can be continued if the switch lock is missing. However, do not remove the switch lock until assembly is completed.
PROTECTOR ‘fess cord into place at each of the three notches indicated. (Fig. 3) Move cord protector until the arrow points to arrow on handle. (Fig. 4 and 5) GROOVE Press groove in cord protector into slot in handle. (Fig. 5 & 6) Pull cord tight.
With sides marked FRONT facing forward, hold tool rack and handle side by side. Align the two hooks on rack with notches at A md B on handle as shown. (Fig. 7) Attach upper hook of rack onto notch A of handle and lower hook onto notch B of handle. (Fig.
Pull bag door latch forward and remove door. Set bag door aside. (Fig. 10) Note round opening and hooks on back of bag compartment. Place opening over dirt tube and align hooks with slots in handle. Press fbmly to snap hooks into handle. (Fig. 11) Note location of tapered rails on bracket and on lower handle.
Align opening in paper bag with dirt tube. (Fig. 14) Push paper bag collar firmly onto tube. (Fig. 15) Fold top of bag under top of compartment. To replace bag door, lift up lower edge of paper bag and insert the 3 tabs on bottom of bag door into the 3 slots on bag compartment.
With cord hooks to back, place assembled handle onto handle base of cleaner body. (Fig. 17) Rock handle side to side while pushing down firmly. Extra pushing effort may be required. Press the handle release lever to move handle to the operating or middle position.
SWITCH LOCK ON/OFF SWITCH Pull switch lock above ON/Off switch straight out. (Fig 20) Dispose of switch lock. Note: If switch lock has come off during assembly make sum switch is in the OFF position (down) before plugging cord into elsctrkal outlet.
Position wands in back of rack as shown. (Fig. 23) Open tool cover (some models only). Position dusting brush (A), fumi- ture nozzle (B), crevice tool (C), and extra belt (D) into side of rack as shown.
The assembled cleaner will look like the drawing below. Operate cleaner only st voltage specMed on data plate on bottom d cleaner. Cleaner description 1. Handle 2.ONK)FF switch 3. cord hooks: wrap cord around hooks for storage. The top hook can be rotated right or left for easy cord release.
How to use To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
t NOZZLE ’ I NOZZLE CONTROL KNOB I Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle. If it is necessary to raise and lower the nozzle for various carpet pile heights, slide the nozzle control knob to the correct setting.
Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge. Before reaching edge, push down on handle. This will lift up the nozzle (front of cleaner) and will prevent rug from clinging to cleaner. Continue to lift up nozzle so that when you have reached the edge, it is completely off the rug.
The Hoover Company 101 East Maple Street North Canton, OH 44720 No. of items Ordered: Please complete this entire form! ~]4010001A Q 160147AG g 4010324A 0 049258AG Q 57363003 Q 38528027 0 38528008 0 38634074 Please Print Your Name and Address carefully in Ink.
.
Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs. with handle in operating position, place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle. As an alternative, you may use the hose and furniture nozzle for stair cleaning.
B. Select proper cleaning tool The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descriptions below. 1. Dusting brush may be used for carved furniture, table tops, books, lamps, lighting fixtures, Venetian blinds, baseboards, shutters, and registers.
Clearing obstructions To check for obstructions, first turn cleaner off and disconnect from electrical outlet; then disconnsct hose from cleaner. Open hose door and carefully remove any visible obstruction. If no obstruction is found, check hose and tools.
Where to buy Paper bags may be purchased from your local Authorized Hoover Dealer (Depot) or from a Hoover Factory Service Center or use the order form packed with your cleaner.
The headlight What to buy This cleaner uses a 12 volt, wedge base type 912 bulb, Hoover part No. 27313-105. How to replace Disconnect ckaner from eiectri- cai outlet and detach hose from cieaner. 1. Remove nozzle control knob on front of hood by grasping knob and pulling up.
5. Remove bulb by pulling straight out of socket; push new bulb into socket until it locks in place. 6. Place hood on cleaner body and press firmly to snap all four latches. Pull up on hood slightly to make sure all four latches are secured. Push nozzle control knob back onto front of cleaner.
How to replace Disconnect deanerfrom eiectri- cal outlet and detach hose from deaner. 1. Place handle in operating position and turn cleaner over. To remove bottom plate, insert end of flat screwdriver into wide area of right-hand slot and push handle of screwdriver to the rear.
5. Slip agitator through new belt (with iettering toward outside of cleaner). Lower end of belt into opening in cleaner body; reposition agitator. 6. Place the three tabs on bottom plate into slots in front of cleaner body. Snap bottom plate into place over agitator.
Agitator brush rolI When to replace Disconnect cleaner from eiectri- cal outiet and detach hose from cleaner. When agitator brushes are worn, the brush roll should be replaced. To check condition of brushes, move edge of card across bottom plate while turning agitator.
3. Pull out shaft, being careful to leave washer on shaft. 4. Reinsert shaft to push out opposite agitator end. 5. Repeat in other direction to push out second agitator end. 6. Discard old agitator brush roll. 7. Place agitator ends into new brush roll, matching projections in roll with openings in ends.
Lubrication The motor is equipped with bearings which contain sufficient lubrication for the liie of the motor. The addition of lubricant could cause damage.
Service lf the problem persists, check the Yellow Pages of your telephone book under ‘Vacuum Cleaners-Household” for your nearest Hoover Factory Sewlce Center or Authorized Hoover Warranty Service Dealer (Depot) where approved HOOVER service and genuine HOOVER replacement parts may be obtained.
Service tf the problem persists, check the Yellow Pages of your telephone book under ?/acuum Cleaners-Household” for your nearest Hoover Factory Service Center or Author&d Hoover Warranty Senrlce Dealer (Depot) where approved HOOVER service and genuine HOOVER replacement parts may be obtained.
Cleaning Effectiveness Per Amp Rating This is m an Amp rating. Amps do m measure dirt removal, only the amount of electricity used. Cleaning Effectiveness Per Amp is determined by dividing this model’s Cleaning Effectiveness* by its Amps.
Full One Year Warranty (Domestic Use) Your HOOVER@ appliance is warranted in normal household use, in actor- dance with the Owner’s Manual against original defects in material and workmanship for a period of one full year from date of purchase.
The Hoover Company wants to quickly resolve any con- cerns about your cleaner or questions regarding its use. However, do not send your cleaner to The Hoover Com- pany in North Canton for service.
デバイスHoover S2200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hoover S2200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoover S2200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hoover S2200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hoover S2200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hoover S2200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoover S2200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hoover S2200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoover S2200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
