HooverメーカーSelf-Propelled WindTunnel Cleanerの使用説明書/サービス説明書
ページ先へ移動 of 13
Self-Pr opelled WindT unnel ™ by HOOVER ® Congratulations on your pur chase! This WindT unnel ™ vacuum cleaner takes HOOVER ® Type “Y” Aller gen Filtration filter bags This pr oduct was desi.
Fill in and r etain For your records, enter the model number and serial numbers in the spaces pro- vided. These numbers are located on the data label on the back of the cleaner body .
3 1. Assembling cleaner Car ton contents Remove all parts from carton and identify each item shown. Make sure all parts are located before disposing of packing. A. Handle screws (in bag with owner’ s manual) B. Hose, cleaning tools and wands C. Handle D.
Place smaller diameter end of wand, into bottom of rack. Snap wand into clip at the top. Repeat with other wand. STEP II Attach hose 1-5 1-8 1-9 1-6 1-7 Align end of hose with projection (E) over slots (F) in dirt duct on back of handle. Slide hose into (F) and twist hose to lock it into place.
14. Carpet height control: slide knob to correct setting for height of carpet being cleaned. 15. Headlight 16. Check bag indicator 17. Bag door 18. Cord hooks: wrap cord around hooks for storage. The top hook can be rotated right or left for easy cord release.
Edge cleaning Special edge groomers ar e provided on both sides of the front of the cleaner to remove dirt in carpet near baseboards and furniture. Guide either side parallel to the edge of carpet or furniture.
7 2-11 How to attach tool cover The tool cover is designed with a “break-away” featur e which allows it to snap free if it is pushed open too far . T o reattach, align hinges of cover with slots on sides of tool storage area. Push cover down to secure in place.
3-1 3-2 3-3 A B C 8 Changing filter bag Disconnect cleaner from electrical outlet. Wher e to buy Filter bags may be purchased fr om Authorized Hoover Dealers (Depot), Leading Retailers, from Hoover Factory Service Centers, or through The Hoover Company on-line at www .
How to reattach filter door The filter door is designed with a “break-away“ featur e which allows it to snap free if it is pushed open too far . T o reattach, align hinges (C) of cover with slots on sides of filter area. Press door back into place.
Replacing brush roll Removing brush roll Slide Brush Roll Control (Fig. 2-9) to “Hard” (OFF) position. T urn cleaner over and remove bottom plate (Fig.
Installing brush roll Grasp brush roll and fit it into position by first sliding end, opposite the belt, into the rectangular slot (G) on side of clean- er . Push other side of brush roll (H) into place. Belt may fit loosely when proper- ly installed.
Possible Cause Possible Solution • Incorrect carpet height setting • Move carpet height control to a higher setting Problem: Cleaner won’t run Problem: Cleaner / tools won’t pick up Possible C.
13 Full One Y ear W arranty (Domestic Use) Y our HOOVER® appliance is warranted in normal household use, in accordance with the Owner’ s Manual against original defects in material and workmanship for a period of one full year from date of purchase.
デバイスHoover Self-Propelled WindTunnel Cleanerの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hoover Self-Propelled WindTunnel Cleanerをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoover Self-Propelled WindTunnel Cleanerの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hoover Self-Propelled WindTunnel Cleanerの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hoover Self-Propelled WindTunnel Cleanerで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hoover Self-Propelled WindTunnel Cleanerを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoover Self-Propelled WindTunnel Cleanerの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hoover Self-Propelled WindTunnel Cleanerに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoover Self-Propelled WindTunnel Cleanerデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。