HooverメーカーU4359の使用説明書/サービス説明書
ページ先へ移動 of 24
.
Fill in and retain! The vacuum cleaner you have just purchased is a combination cleaner. It is used for carpet and rug cleaning and may be used with took for above the floor cleaning. The model and serial number appear on the bottom of the cleaner base.
Important Safeguards! l Read all instructions. l Warning: Electric shock could occur if used outdoors or on wet surfaces. l Close supervision is necessary when any appliance is used by or near children. Do not allow vacuum cleaner to be used as a toy or to run unattended at any time.
Unpacking Unpack the cleanerfrom the carton and identify the parts q shown. Remove and disoose of F the cardboard packing. . A. Upper handle section B. Lower handle section C. Cleaner main body and hood assembly D. Outer bag assembly E. Throw away bag F.
1. Headlight 2. Hood 3. Pile Height Adjustment Display (some models only): indicates the four positions set by the Adjustment Lever for cleaning various e carpet piles. Four positions are: LOW, NORMAL, HIGH and SHAG. 4. Adjustment Lever for Carpet Pile Height: to adjust the underside of the cleaner (nozzle location) to the carpet pile height.
How to assemble Before assembly, identify the type of handle on your cleaner: 1) Square handle with molded grip or 2) Round handle. Then as- semble the cleaner according to handle type. I) Square handle with molded grip i A. Put handle together Remove cardboard from end of handle sections.
Reinsert bolt through small holes of handle and secure with nut. Tighten nut with screwdriver. Proceed to Section C. 2) Round handle A. Put handle together Remove cardboard from the end of handle sections. Remove bolt and nut from upper handle sec- tion.
Replace plate on back of handle, by inserting projection on plate into lower hole on handle. Tabs on handle bail will fit into notches on plate. Position nut on bolt and tighten with screwdriver.
D. Attach throw away bag to cleaner To attach throw away bag to cleaner, unzip outer bag. Pull out tube. Push bag collar firmly onto tube by first positioning bottom of collar, and then top, onto tube. Make sure the collar is pushed past the raised portion at the top and bot- tom of the tube.
How to use ON-OFF switch To turn cleaner ON, push switch down. To turn cleaner OFF, push the switch up. Some models are equipped with a two-speed Power SurgeTM switch. When the switch is pushed up as far as possible, it is in the OFF position. Normal Speed is to be used for regular cleaning of carpet and rugs and when using cleaning tools.
Adjustment for carpet pile height The cleaning of carpet and rugs takes place at the nozzle. This is the opening at the bottom of the cleaner where the agitator is lo- cated. It is necessary to raise and lower the nozzle for various carpet pile heights.
Cleaning lightweight flexible rugs Lightweight flexible rugs used on hard surface floors in entrances, bathrooms, etc. should be cleaned by the following method. Stand on one end of the rug and move the cleaner toward the oth- er end or edge. Before reaching the other end, push down on the handle.
Edge cleaning This feature improves the cleaning of carpet edges near baseboards and solid furniture. Dust and lint tend to collect along these edges. The cleaner bottom plate has been designed with a passageway for dirt to enter the nozzle from the side to increase cleaning ability of edges.
The converter must first be as- sembled to the hose by inserting the converter into the hose con- nectar . 1 CONNEC-TOR CONi/ERTER 1 Push connector and converter to- gether and twist until the projec- tions on the converter fit into the holes on the hose connector.
Pivot converter until it covers the opening. To lock in place, turn red con- verter lock toward the hose. Raise cleaner to upright position. B. Select proper cleaning tool The cleaning tools have many uses. Select the tool best suited for the cleaning task from the de- scriptions below.
C. Attach tool After choosing the proper tool for your particular task, attach it to the end of the hose grip. The outer plastic ring on the end of the hose grip has a slot. Turn the ring until that slot aligns with the slot in the hose connec- tor. Insert the tool so that the button on the tool fits into the slot in the end of the hose grip.
Maintenance The following sections are concerned with proper maintenance of the cleaner. Familiarize yourself with these home maintenance tasks and keep this owner’s manual in a convenient place where you can refer to it when needed. Proper use and care of your cleaner will assure continued cleaning effectiveness.
The headlight How to replace the headlight Disconnect cleaner from electri- cal outlet. This cleaner uses 12 volt, wedge base type 912 bulbs. 1. Set adjustment lever for pile height to the “NORMAL” or “HIGH” position. 2. Turn cleaner over and remove the two screws indicated in the il- lustration.
1 How to replace the belt Disconnect cleaner from electri- cal outlet. 1. Turn cleaner over. Remove bottom plate by releasing lat- ches. 2. Release worn belt-from pulley. 3. Lift out agitator, remove old belt and place new belt in groove of agitator. 4.
5. Place belt on pulley. belt nearer cleaner should be in line with projections on bottom of cleaner. Placing the belt in this position enables the agitator to rotate in the proper direction. 6. Replace bottom plate, by put- ting metal knobs on plate into wire holders underneath front of cleaner.
How to replace the brushes (Brushes - HOOVER part No. 48445001) Disconnect cleaner from electrical outlet. 1. To replace worn brushes, remove bottom plate, belt and agitator, fol- lowing directions given on preceding pages. 2. Turn end plates of agitator in opposite directions until one end plate comes off.
If you have a problem This appliance was inspected thoroughly and was in good operating con- dition when it was shipped from the factory. If a minor problem devel- ops, it usually can be remedied quite easily when the cause is identified. Accordingly, this check list is provided for your convenience.
Lubrication The motor is equipped with one ball bearing and one sleeve bearing. These bearings contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing.
VCMA VACUUM CLEANER MANUFACTURERS ASSOCIAT I ON (HOOVER - AN ASSOCIATION MEMBER) Service To The Consumer Since 1913 This information has been compiled by the Vacuum Cleaner Manufacturers Associ- ation from Government and Private Sources concerned with product safety.
デバイスHoover U4359の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hoover U4359をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoover U4359の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hoover U4359の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hoover U4359で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hoover U4359を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoover U4359の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hoover U4359に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoover U4359デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。