HP (Hewlett-Packard)メーカー8550MFPの使用説明書/サービス説明書
ページ先へ移動 of 64
English 8550, 8550N, 8550DN, 8550GN, 8550MFP Printer *C7096-90923* *C7096-90923* C7096-90923 Getting Started Guide Copyright© 2000 He wlett-Packard Company Printed in USA 04/00 Manual Part No.
.
HP Color LaserJet 8550, 8550N, 8550DN, 8550GN, 8550MFP Pr inter Getting Star ted Guide.
Copyright Inf ormation ©2000 Hewlett-P ackard Company All Rights Reserved. Reproduction, adaptation, or translation without pr io r wr itten permission is prohibited, exce pt as allowed under the cop yr ight laws .
EN 1 Contents Printer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Step 1: Preparing a Location for the Printer .
2 EN Printer Inf ormation Configurations This printer is av ailable in five configur ations, as described below: HP Color LaserJet 8550 The HP Color LaserJet 8550 comes standard with a 100-sheet tra y 1, a 500-sheet tra y 3, a printer stand, and 32 MB RAM.
EN Printer Information 3 HP Color LaserJet 8550MFP The HP Color LaserJet 8550MFP comes standard with a 100-sheet tra y 1, a 500-sheet tra y 2, a 500-sheet tra y 3, a duple xer , 64 MB RAM, an HP JetDirect print ser ver (10/100 Base-TX), an internal hard disk, a printer/copy module stand, and a cop y module.
4 EN Step 1: Preparing a Location f or the Printer Figure 1 A T op View (with optional m u lti-bin mailbox and tra y 4) B F ront View (with optional multi-bin mailbo x and tra y 4) This printer requir.
EN Step 2: Unpacking the Printer 5 Step 2: Unpac king the Printer CA UTION Do not plug the printer into a power source until all shipping material is remov ed.
6 EN T o unpack the printer 1 Remov e all external packing tape from the printer . 2 Open the low e r left door and push down the g reen lev er on the r ight side of the fuser . Then, remov e the orange shipping notice from the fuser . 3 Open the front door .
EN Step 2: Unpacking the Printer 7 4 Remov e the orange packing material from the lowe r (green) le ver . 5 Press the white button on the lower (green) le ver and s wing the lev er to the right. 6 Remov e the packing material from inside the printer and then swing the low er (green) lev er back to the left, making sure the le ver clicks into place.
8 EN Note F ollow steps 9-12 t o attach the five stabilizing legs to the bottom of tray 4. If the five stabilizing legs (which are in addition to the f our locking wheels) are already attached, proceed to step 13. 9 Locate the five stabilizing legs that came with the printer .
EN Step 2: Unpacking the Printer 9 13 Remov e the packing tape from tra y 4. 14 Firm ly grip the handle in the center of tra y 4, squeeze the release le v er , and pull the tra y out until it stops. 15 Remov e the two orange pac king clips from inside tra y 4 by squeezing the sides of the clips and pulling them out.
10 EN Step 3: Installing the Cables T o connect the power cor d to a printer with a stand Note Make sure that the printer is off (pow er button out) bef ore connecting the power cord.
EN Step 3: Installing the Cables 11 T o connect the interface cable and power cor ds for a printer with an optional tra y 4 Note Make sure that the printer is off (pow er button out) bef ore attaching the interf ace cable and connecting the po wer cords.
12 EN 5 Push the two cab les extending from the powe r pack into the space between the printer and tra y 4 along the back of the printer . 6 Plug the shor ter of the two cables into the connector on the back left corner of the printer . 7 Plug the longer of the two cab les into the connector on the back left corner of tra y 4.
EN Step 3: Installing the Cables 13 9 Roll the printer to its per manent location, where all four wheels rest on a le vel floor surf ace, and stabilize it b y pushing the locking tabs on the tr a y's wheels to the lock ed position.
14 EN Step 4: Connecting the Printer to the Netw ork If you will connect the computer to the printer with a parallel cable , see “ To connect a parallel cab le ” later in this Step .
EN Step 4: Connecting the Printer to the Network 15 T o connect a parallel cable T o print through the parallel por t, the printer requires a 25-pin male/micro 36-pin male ( “ C-size ” ) par allel cable that is IEEE-1284 compliant. The cable is not included with the printer .
16 EN Step 5: Changing the Printer Contr ol P anel Overla y and Language (Optional) Replace the printer control panel overla y with the one included f or your language, if applicable . Then configure the pr inter control panel to show printer messages in your language .
EN Step 5: Changing the Printer Control Panel Overlay and Language (Optional) 17 Selecting the Displa y Language Use the printer control panel to set the pr inter to displa y pr inter messages and print configuration pages in a variety of suppor ted languages.
18 EN Step 6: Installing the Consumables Figure 4 The f ollowing par ts (consumables) are included with the printer : A Imaging Drum B Black T oner Car tr idge C Color T oner Car tr idges: yello w , m.
EN Step 6: Installing the Consumables 19 T o install the imaging drum CA UTION T o pre vent damage to the printer , do not mov e the printer after the imaging dr um or any of the toner car tridges hav e been installed. 1 Leav e the printer powered on and open the front door of the printer (A).
20 EN T o install the blac k toner car tridge 1 Remov e the blac k toner car tr idge from its packaging. 2 Hold the car tr idge with both hands and gently rock it se v eral times to distribute the toner . Note Do not shake or roc k the car tridge if the orange ring has been remov ed.
EN Step 6: Installing the Consumables 21 4 Place one hand on the car tr idge and use the other hand to pull the orange ring and remove the seal. Set the seal aside. Note If toner gets on f abr ic, wipe the toner off with a dr y cloth and then wash the clothing in cold water .
22 EN T o install the color toner car tridges 1 T ur n the printer on ( power button in). 2 Press the blue b utton belo w the clear door to tur n the color toner carousel to the slot marked w ith a yello w stic ker .
EN Step 6: Installing the Consumables 23 5 Remov e the toner car tr idge that matches the color of the stick er in the carousel slot from its packaging. CA UTION Do not lift or remov e the shutter (A) on the car tr idge. Hold onto the ends of the toner car tr idge.
24 EN 9 Close the clear door . Note If the clear door does not close, mak e sure that the blue le ver is all the w ay to the left and the orange seal w as remov ed. 10 Press the blue b utton to rotate the carousel to the slot marked with a magenta stick er and repeat steps 3 through 9.
EN Step 7: Loading the Input Trays 25 Step 7: Loading the Input T ra ys Figure 6 The printer has the follo wing input trays: A T ra y 1 (multipur pose tra y) B T ra y 2 (some pr inter models only) C T.
26 EN Loading media into trays 2 (some printer models only) and 3 Note Bef ore loading media into trays 2 and 3, ve rify that the spacers were remov ed from both tra ys when “ Step 2: Unpacking the Printer ” was perf or med.
EN Step 7: Loading the Input Trays 27 5 Adjust the left media guide by pushing it in (A) and lifting it up and out (B). Note Lift here (C) to remov e paper from the tra y . 6 P osition the guide ov er the appropriate media size marked in the tra y . 7 Press the guide into the rear slot (D), and then low e r it down (E) into the front slot (F).
28 EN 9 Make sure that the media-siz e tab on the front of the tra y is set to the correct media size . 10 Slide the tra y back into the printer . 11 Attach the left output bin (A) to the left side of the printer if you did not install an optional multi-bin mailbo x.
EN Step 7: Loading the Input Trays 29 Loading media in the optional tray 4 Note Bef ore loading media into tray 4, v erify that the spacers were remo ved from the tra y when “ Step 2: Unpacking the Printer ” was perf ormed.
30 EN 5 Load media into the tra y up to the media-fill mark. For e xample, up to 2,000 sheets of 20 lb . (75 g/m 2 ) bond paper will fit in the tra y . For inf or mation on loading and or ienting media, see the online user guide or the quick ref erence guide.
EN Step 8: Configuring Input Trays 31 Step 8: Configuring Input T ra ys When input tra ys are configured correctly , the printer will pr int based on media type and size and will automatically use the correct input tra y . F or example, tr ay 2 could contain letterhead; tra y 3, plain legal-sized paper ; and tra y 4, plain letter-sized paper .
32 EN Configuring Media T ype and Siz e Configuring the media type is beneficial for se veral reasons: z Configuring the media type prev ents pr inting on the wrong (and possibly more e xpensive) media. z If a user changes the type of media in an input tra y , other users can still print on the corr ect media.
EN Step 9: Printing a Configuration Page 33 Step 9: Printing a Configuration P age Use the printer control panel to pr int a configuration page and v er ify that the printer was installed correctly .
34 EN T o verify communication with a parallel cab le T o verify that the printer and computer are set up correctly to communicate with each other , print a director y list. 1 T ur n the computer and printer on and wait f or the pr inter to bring itself online (the printer is online when the Ready light on the printer control panel is lit).
EN Step 9: Printing a Configuration Page 35 Comm unicating with an optional HP JetDirect internal print server If the printer contains an optional HP JetDirect inter nal print ser ver , and you cannot comm unicate with the printer ov er the network, verify the operation of the print ser ver .
36 EN 3 Reinstall the print ser ver . 4 V er ify that the configuration of the connecting network de vice (such as a 10/100TX network switch) matches . For e xample, to set the print ser ver f or 100TX Full-duplex oper ation, the por t on the network s witch must also be set for 100TX Full-duple x operation.
EN Step 10: Understanding the Software 37 Step 10: Understanding the Software CD-ROMs are included with this printer . The CD-ROMs are divided by language .
38 EN Installing the Software F or pr inters with the optional HP JetDirect inter nal print ser ver , yo u might hav e to set cer tain network parameters depending upon the network configuration. F or most networks, you can configure these parameters from the HP W eb JetAdmin software which is a vailab le on the HP W eb site (www .
EN Step 10: Understanding the Software 39 Accessing the Online User Guide The online user guide is automatically installed with the T ypical install. If you w ant to install only the online user guide, use the Custom option from the installer . (See Step 11: Windows Netw ork Installation.
40 EN T o access the online user guide from the CD-R OM 1 Inser t the CD-ROM that corresponds to y our language into the CD-ROM drive . 2 If you already ha ve Adobe Acrobat Reader installed on y our computer ’ s hard drive , open Acrobat Reader and then open the online user guide from your CD-R OM drive.
EN Step 11: Windows Network Installation 41 Step 11: Windows Netw ork Installation In Microsoft Windows 9x, Windo ws NT ® 4.0, and Windows 2000, the installation software detects both the version of Windows that is in use and the language that is selected in the operating system.
42 EN 7 T o install printer software for the language and v ersion of Windows on the computer , clic k Continue . T o install printing software in another language, clic k Exit and use the Structure of the CD-ROMs section in Step 10: Understanding the Software to find the path f or the language you w ant to install.
EN Step 11: Windows Network Installation 43 Configuring the Printer on the Netw ork Bef ore y ou can use the pr inter , configure it on the networ k. HP recommends that you use a printer management utility such as the HP W eb JetAdmin software , PCONSOLE, or NW ADMIN.
44 EN Creating Disk Images with the Windows Installer 1 Inser t the CD-ROM into the CD-ROM driv e. 2 In the Windows 3.1 x Program Manager , select Run from the File menu. - Or - In Windows 9x, NT 4.0, or Windows 2000, clic k St ar t then select Run . 3 T ype D:<language><OS>Disk1Setup.
EN Step 11: Windows Network Installation 45 Note Do not install the PCL or P ostScript dr ivers on workstations that connect to Windows NT and Windo ws 2000 ser vers when y ou install other network client software . Clear the PCL and P ostScr ipt Dr iver check bo x e s in the Components list during the Custom Install.
46 EN T o connect workstations to the print server Connect the printer dr ivers to the printer on the proper por t. z In Windows 3.1, double-clic k Printers in the Control P anel, then select Connect to connect the printer driver to the network.
EN Step 11: Windows Network Installation 47 T o connect Windows 9x, Windo ws NT 4.0, and Windows 2000 w orkstations directly to the printer 1 Click Start . 2 Click Settings . 3 Click Printer s . 4 Right-click the icon f or this printer to open a shor tcut menu.
48 EN Step 12: IBM LAN Netw ork Installation Distrib uting the Printer Software to Network Clients Bef ore a client can print to the printer, the printer software must be installed on the clients workstation.
EN Step 12: IBM LAN Network Installation 49 8 In the Directory field, type: D:englishOS2<driver (This assumes that the CD-ROM driv e is the D drive and that y ou are installing the English driver .) Fo r <driver> , type: PCL or PS . 9 Click Refresh .
50 EN Step 13: Macintosh Netw ork Installation Installing the Macintosh Printer Software The Macintosh printer dr iver f or this printer suppor ts system version 7.0 or later . F or an EtherT alk or LocalT alk network, install the sof tware on each workstation.
EN Step 13: Macintosh Network Installation 51 Connecting Netw ork Clients to the Printer If you are not using a print spooler or a print queue, f ollow the directions below to connect the printer drivers to the printer automatically .
52 EN 4 F rom the list of pr inter names along the right side of Chooser , select the name of the printer (ev en if it is the only one that appears). 5 Click Setup . 6 Click Se lect PPD . 7 F rom the list of PPD files, clic k HP Color LaserJet 8550 Printer .
EN Step 13: Macintosh Network Installation 53 Distrib uting the Printer Software to Network Clients Bef ore a client can print to the printer, the printer software must be installed on the clients workstation.
54 EN T roub leshooting Checklist If the printer does not appear to be functioning correctly , check the f ollowing items: Problem or Err or Message Solution The printer control panel display is blank. Mak e sure the pr inter ’ s power s witch is on.
EN Troubleshooting Checklist 55 F or more pr inter control panel messages and troubleshooting solutions, see the online user guide . Cannot print using a sharing devi ce. T r y to isolate the cause of the problem. T est the pr inter using a cable conne cted directly from the computer to th e printer .
56 EN.
EN Troubleshooting Checklist 57.
58 EN.
.
English 8550, 8550N, 8550DN, 8550GN, and 8550MFP Printer *C7096-90923* *C7096-90923* C7096-90923 Getting Started Guide Copyright© 2000 He wlett-Packard Company Printed in USA 04/00 Manual Part No.
デバイスHP (Hewlett-Packard) 8550MFPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) 8550MFPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) 8550MFPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) 8550MFPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) 8550MFPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) 8550MFPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) 8550MFPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) 8550MFPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) 8550MFPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
