HP (Hewlett-Packard)メーカーC6200の使用説明書/サービス説明書
ページ先へ移動 of 189
HP Photo smar t C6 200 A ll-in- One se r i es W indo w s He lp.
Contents 1 HP Photosmart C620 0 All-in-One series He lp ............................. ................................... ........3 2 HP All-in-One ov erview The HP All-in-One at a glance............ ...................................................
10 Use the copy fe atures Make a copy............................................................ ........................................................ .........85 Preview your copy job................................................... ...........
1 HP Photosmart C6200 All-in- One series Help For information a bout the HP All-in-One, see: •“ HP All-in-One overvi ew” on page 5 •“ Find more i nformation” on page 13 •“ Finish setti.
Chapter 1 4 HP Photosmart C6200 All-in-One series Help HP Photosmart C620 0 All-in- One series Help.
2 HP All-in-One overview Use the HP Al l-in-One to quickly and easily make copies, scan docum ents, or print photos from a memory card. HP papers th at are specifically designed for th e type of project you are printing pr oduce the best results.
Label Description 6 Paper tray extender (also referred to as the tray extender) 7 Paper-width and paper-length guides for the photo tray 8 Photo tray 9 Paper-length guide for the main input tray 10 In.
Control panel features The followin g diagram and related tabl e provide a quick reference t o the HP All-in-One control panel features. Ethernet Label Icon Name and Description 1 Color graphics display (also re ferred to as the display): Displays menus, photos, and messages.
Label Icon Name and Description 11 Scan Menu : Opens the Scan Menu where you can select a destination for your scan. 12 Start Scan : Starts a scan. 13 Copy Menu : Opens the Copy Menu where you can select copy options, such as number of copies, paper size, and paper type.
Icon Purpose Shows that an unknown ink cartridge is inserted. This icon migh t appear if an ink cartridge contains non-HP ink. Indicates that there is a wired network connection. Display sl eep state To prolong the life of the di splay, it dims after two minutes of inact ivity.
Photosmart Expres s Menu The follo wing options are availabl e in the Photosmart Expres s menu when you insert a memory card or press Photo Menu on the control pan el. View Print Create Shar e Save Scan Menu The followi ng options are available wh en you press the Scan Menu button on the control panel.
Network Copy Menu The followin g options are available wh en you press the Copy Menu button on the control panel. Copies Size Quality Lighter/Darker Previ ew Crop Paper Siz e Paper Type Margin Shift E.
For more information o n using the HP Photosmart Software: • Check the Contents panel on the left. Look for the HP Photosmart Software Help contents book at the top. • If you do not see the HP Photosmart Softwar e Help contents book at the t op of the Contents panel, access the software h elp through the HP Solution Cente r.
3 Find more information You can access a variety of resources, both printed and onscreen, that provide information abo ut setting up and using the HP All-in-One. Setup Guide The Setup Guide provides instructions for setting up the HP All-in -One and installing software.
Chapter 3 14 Find more information Find more information.
4 Finish setting up the HP All-in- One After you have completed the steps in your Setup Guide, re fer to this section to help you finish setting up the HP All-in-One. This section contains important setup -related information f or your device, including inform ation on setting preferences.
3. Press to highlight Set Country/Region , and then press OK . 4. Press to scroll through the countries/regions. Wh en the country/region yo u want to use appears, press OK . 5. When prompted to confirm the country/region, press to hi ghlight Yes or No , and then press OK .
Play a slideshow on the display You can set up the HP All -in-One to play a slideshow on th e display, similar to a screensaver on a computer, w hen you are not using the device.
Description Recomme nded number of connected computers for best performance Supported software features Setup instructions rear USB 2.0 High Speed port on the HP All-in-One. Ethernet (wired) connection Up to five computers connected to an HP All- in-One using a h ub or router.
If you want to: See this section: Change the HP All-in-One from a U SB connection to a network connection. NOTE: Use the instructions in this section if you first installed the HP All-in -One with a USB connection, and you now want to change to a n Ethernet network connection.
❑ A functional Ethernet network that includes a router, switch, o r hub with an Ethernet port. ❑ CAT-5 Ethernet cable. Although standard Et hernet cables look similar t o standard telephone cables, they are not interch angeable. There is a diff erent number of wires in each o ne, and each has a different conne ctor.
3. Connect the other en d of the Ethernet c able to an avai lable port on your Ethernet router or switch. 4. Once you have connected th e HP All-in-One to the network, install the software.
7. If you disabl ed any virus detection software on your computer, make sur e to enable it again. 8. To test your netw ork connection, go to your computer and print a self-test repo rt to the HP All-in-One.
• Use the Embedded W eb Server • Network configu ration page definitions Change ba sic network se ttings from the control panel You can perform a variety of ne twork management tasks from the control panel, such as printing the net work settings and restoring ne twork defaults.
This section contains the foll owing topics : • Set link speed • Change IP settin gs Set link spee d You can change the spe ed at which data is transm itted over the network. The default is Automatic . To set link speed 1. Press Setup . 2. Press until Network is hig hlighted, then press OK .
6. Press to highlight one of the following IP sett ings, and then press OK . • IP Addres s • Subnet Mask • Default Gateway 7. Enter your changes, and the n press OK to confirm the setti ng.
4. Click the Settings tab to access device settings. 5. Make any config uration changes, and the n click Apply . 6. Close the Embedd ed Web Server. Related topics “ View and print network settings.
General network settings The followin g table describes the general network settings shown on the network configuratio n page. Paramete r Description Network Status Status of the HP All-in -One: • Ready : The HP All-in-One is ready to receive or transmit data.
Parameter Description NOTE: Some Internet service providers (ISPs) require that you register the MAC address of the Network Card or LAN Ad apter that was connected to your cable or DSL modem during installation. IP Address This address uniquely identifies the devic e on the network.
Paramete r Description broken up into packets. Each packet contains the destination address as well as the data. Total Packets received The number of packets received by the HP All-in-One without error since it has been turned on. The counter clears a fter the HP All-in-One is turned off.
the hub. Hubs are passive; othe r devices on the network plug into the hub in order to communicate with one another. A hub doe s not manage the network. IP address A number that uniquely identifies the device on the network. IP ad dresses are assigned dynamically through DHCP or AutoIP.
5 How do I? This section contai ns links to commonly performed tasks, such as printing photos, scanning, and m aking copies. •“ How do I print 10 x 15 cm (4 x 6) inch borderless photos fr om a mem.
Chapter 5 32 How do I? How do I?.
6 Load originals and load paper You can load many differen t types and sizes of paper in the HP All-in-One, in cluding letter or A4 paper, legal paper, p hoto paper, transparencie s, envelopes, and HP CD/D VD tattoo labels.
Choose papers for printing and copying You can use differ ent types and si zes of paper in the HP All -in-One. Review the foll owing recommendati ons to get the best printing and copying quality. W henever you change paper types or si zes, remember to change those settings.
HP Premium Ink jet Paper HP Premium Inkjet Paper is the ultimate coated paper fo r high-resolution usage. A smooth, matte fini sh makes it ideal for your hi ghest-quality documents. HP Bright Whit e Inkjet Paper HP Bright White In kjet Paper delivers high-c ontrast colors and sharp text.
HP CD/DVD Tattoos HP CD/DVD Tattoos allow you to personalize your CDs and DVD s by printing high- quality, low -cost CD or DVD labels. To order genuine HP sup plies for the HP All-in-One, go to www.
This section contai ns the following topics: • Load full -size paper • Load 10 x 15 cm (4 x 6 inch) ph oto paper • Load postca rds, Haga ki, or index cards • Load envelop es • Load other types of pa per Load full-size pa per You can l oad many type s of letter, A4, or legal paper in to the main inp ut tray of the HP All- in-One.
4. Slide the paper-w idth and paper-length gui des inward until they stop at the edges of the paper. Do not overload t he main input tray; make sure the stack of paper fits within the input tray and is no hi gher than the top of the paper-wi dth guide.
2. Insert the st ack of photo paper in to the photo tray w ith the short edge fo rward and the print side down. Slide t he stack of photo paper forward until it stops. If the phot o paper you are using has perforated tab s, load the photo paper so that the tabs are closest to you.
2. Insert the stack of cards into the photo tray with the short edge forward and t he print side down. Slid e the stack forward until it st ops. 3. Slide the pape r-length and paper-width guides inward against the stack of cards until the guides stop.
To load envel opes 1. Pull out the main input tray, and then slide t he paper-width and pap er-length guides to their outermo st positions. 2. Remove all paper from the main input tray. 3. Insert one or more envelopes into the far-right side of th e main input tr ay with the envelope flaps up and on the left.
Load other type s of paper The followin g types of paper are designed for speci al projects. Create your p roject in the HP Photosmart Softw are or another application, set the pap er type and size, and then print.
Related topics •“ Change the prin t settings for the current job” on page 46 •“ Recommended p apers for printing only” on page 35 Avoid paper jams To help avoid paper jams, follow th ese guidelines. • Remove printed pape rs from the output tray f requently.
Chapter 6 44 Load originals and load paper Load originals and load paper.
7 Print from your computer The HP All-in-On e can be used with any software ap plication that all ows printing. You can print a range of proje cts, such as borderless imag es, newsletters, greeting cards, iron-on transfers, and posters.
5. Select the appropriate options for your prin t job by using the features avai lable in the Advanced , Printing Shortcuts , Features , and Color tabs. TIP: You can easily sel ect the appropriate op tions for your print job by choosing one of the predefi ned print tasks on the Printing Shortcuts tab.
To set the paper size 1. Make sure you have pa per loaded in the input tra y. 2. On the File menu in your software application , click Print . 3. Make sure the HP All- in-One is the selected printe r. 4. Click the button t hat opens the Properties dial og box.
To set the paper type for printing 1. Make sure you have pa per loaded in the in put tray. 2. On the File menu in your softwa re application, click Print . 3. Make sure the HP All-in-One is the selected printer. 4. Click the button that opens the Properties dialog box.
6. In the Print Quality drop-down list, select the ap propriate quality sett ing for your project. NOTE: To view the maximu m dpi that t he HP All-in -One will p rint, click Resolution . 7. In the Paper Typ e drop-down list, select the t ype of paper that you have loade d.
To change the saturation, brightness, or color tone 1. Make sure you have pa per loaded in the in put tray. 2. On the File menu in your softwa re application, click Print . 3. Make sure the HP All-in-One is the selected printer. 4. Click the button that opens the Properties dialog box.
To change the defa ult print settings 1. In the HP Solution Center, click Settings , point to Print Settings , and th en click Printer Settings . 2. Make changes to t he print settings, and click OK . Printing shortcuts Use printing shortcuts to print with print settings that you u se often.
To create a printi ng shortcut 1. On the File menu in your softwa re application, click Print . 2. Make sure the HP All-in-One is the selected printer. 3. Click the button that opens the Properties dialog box. Depending on your sof tware application, th is button might be cal led Propertie s , Options , Printer Setup , Printer , or Preferen ces .
• Print on transp arencies • Print a group of add resses on labels or envelopes • Print a poster • Print a Web page Print a border less image Borderless pri nting lets you print to the top, bottom, and sid e edges of 10 x 15 cm (4 x 6 inch) photo p aper.
4. Click the button that opens the Properties dialog box. Depending on your sof tware application, th is button might be cal led Propertie s , Options , Printer Setup , Printer , or Preferen ces . 5. Click the Features tab. 6. In the Basic Options area, from the Paper Type drop-down list, select More .
Print using Maximum dpi Use Maximum dpi mode to print high-qua lity, sharp images . To get the most bene fit from Maximum dpi mode, use it to print high-quality imag es such as digital phot ographs. When you select the Maximum dpi setti ng, the prin ter software displays the optim ized dots per inch (dpi) that the HP Al l-in-One will print.
Print a multiple-page document as a booklet The HP All-in-One a llows you to print your document as a sm all booklet, which you can fold and then staple together. For best results, design your docume nt to fit on a multiple of four p ages, such as an 8, 12, or 16-page program f or a child's school play or for a weddin g.
13 5 7 9 11 Figure 7-1 Left-edge binding for left-to-r ight languages 1 3 5 79 1 1 Figure 7-2 Right-edge binding for right-to-left languages Print multiple pag es on a si ngle sheet You can print up to 16 pages on a single sheet of paper. To print multiple pages on a sin gle sheet 1.
8. In the Page order list, click an appropriate pag e order option. The sample outp ut graphic is numbered t o show how the p ages will be ordered i f you select each option.
6. In the Layout Options area, select Front to Back in t he Page Order option. NOTE: If you set your document to prin t on both sides of t he page, the Front to Back option is not ava ilable. Your document wi ll automatically print in the correct order.
6. In the Basic Options area, from the Paper Type drop-down lis t, select More . Th en select the app ropriate paper type. TIP: If you want to m ake notations on the b ack of the transparencies and erase them later wi thout scratching the original, clic k the Advanced tab , and select the Mirror Ima ge check box.
Print a poster You can create a poster by print ing a document on multiple pages. The HP All-in-One prints dotted l ines on some pages to ind icate where to trim the pages before taping them together. To print a poster 1. Make sure you have pa per loaded in the input tra y.
To print a Web page 1. Make sure you have pa per loaded in the main input tray. 2. On the File menu in your Web browser, cli ck Print . The Print dial og box appears. 3. Make sure the HP All-in-One is the selected printer. 4. If your Web browser support s it, select the items on t he Web page that you want to include in t he printout.
3. Double-click the HP All-in-One icon. TIP: You can also dou ble-click the printer icon in the Windows taskbar . 4. Select the prin t job you want to cancel. 5. On the Document menu, click Cancel Printing or Cancel , or press the Dele te key on your keyboard.
Chapter 7 64 Print from your computer Print.
8 Use the photo features The HP All-in-On e is equipped with memory card slot s that enable you to print or edit photos from a memory card w ithout uploading your photos to a com puter first.
when images are ready t o be viewed. The Photo light is located ne ar the memory card slots and is indicated by a came ra icon. CAUTION: Do not pull out the me mory card while the Photo light i s flashing. A flashing light means t he HP All-in-O ne is accessin g the memory card .
2. Load up to 10 x 15 cm (4 x 6 in ch) photo paper in the photo tr ay or full-size photo paper in the ma in input tray. 3. Press until View is highlight ed, and then press OK . The View Photos screen appea rs. 4. Press or to scroll through the t humbnails of your photos.
1. Insert a memory card int o the appropriate slot on the HP All -in-One. The Photosmart Express menu appea rs, with the most recent photo shown on the display. View Print Create Share Save 2. Load up to 10 x 15 cm (4 x 6 inch) photo pa per in the photo tray or full-size photo paper in the mai n input tray.
9. With Print Preview highlighte d, press OK . The Print Preview screen appears, showi ng how your photo(s) wil l look when printed. 10. (Optional) If you w ant to check and/or modify any of your p rint settings, use or to highli ght Settings and press OK .
4. Press or to scroll through the proj ects, and then and then press OK to select the project you want. • Album Pages : Enables you to select multiple photos a nd print them onto a seri es of themed al bum pages, which you can t hen bind to create a photo albu m.
To send photos from a memory c ard 1. Insert a memory card in to the appropriate slot on the HP All-in -One. The Photosmart Expre ss menu appears, wi th the most recent photo shown on the display. View Print Create Share Save 2. Press until Share is highli ghted, and then press OK .
To save photos 1. Insert a memory card int o the appropriate slot on the HP All -in-One. The Photosmart Express menu appea rs, with the most recent photo shown on the display. View Print Create Share Save 2. Press until Save is hi ghlighted, and then p ress OK .
• Automaticall y enhance your photos • Fix a faded orig inal Zoom and pan to cr op a photo The HP All-in-One enabl es you to zoom in or out on a specific area of a photo. Wh en you print the photo, the photo is cropped so onl y the area shown on the display prints.
To rotate a photo 1. Insert a memory card int o the appropriate slot on the HP All -in-One. The Photosmart Express menu appea rs, with the most recent photo shown on the display. 2. With View highlighted, press OK . You can use or for highlighting opti ons.
Print a frame around your photo You can print a decorative colored border around the outside edge o f your photo to frame the photo. NOTE: The changes you make t o the photo apply only to viewing and pri nting the photo. The chang es will not be saved on the memory card.
6. In the Photo Opti ons menu, use or to highlight Edit P hoto , and then press OK . The Edit Photo menu appears. 7. Use or to highlight Color Effect , and then press OK .
When this feat ure is enabled, the HP All-i n-One uses HP Real Life Technologies to: • Adjust the brightness or da rkness of your photos (shown in print preview and pri nted output) • Adjust the l.
Related topics “ Make reprints of yo ur photos” on page 79 Chapter 8 78 Use the photo features Photos.
9 Use the scan features Scanning is the process o f converting text and pictures into an electronic forma t for your computer. You can scan almost anythin g (photos, magazine articles and text documents) on the HP All-in -One.
To chang e print sett ings bef ore repri nting your or iginal pho to a .P r e s s OK to change pri nt settings. The Sourc e of Or iginal screen appears. b .P r e s s or to highlight an y option and press OK . The Print Layout screen appears. c .P r e s s or to highlight the print layout pa ttern and press OK .
To scan to a computer 1. Load your original print side down on the right front corner of the glass. 2. Press Scan Menu on the control panel. 3. Press to highlight Scan to Computer , and then press OK . 4. If the HP All-in-O ne is connected to one or more comp uters on a network, do the following: a .
3. Press Scan Menu on the control pa nel. 4. Press to highlight Scan to Mem ory Card , and then press OK . NOTE: Alternatively, you can press Start Scan instead of OK . The HP All-in-One scans the image and saves the file to th e memory card in the JPEG format.
Share a scanned image with friends and relatives You can easily share scanned ima ges with friends and family using the HP Photosmart Share online se rvice. HP Photosmart Share enables you to send images to others as e- mail or upload ph otos to an online photo album or photo finish ing service.
Chapter 9 84 Use the scan features Scan.
10 Use the copy features The HP All-in-O ne enables you to produce hi gh-quality color and black-an d-white copies on a variety of paper types, includin g transparencies.
3. Press to highlight Preview , and then press OK . An image on the displa y shows how your copy will print. 4. Press Start Copy Black or Start Copy Color to accept t he preview and begin copying. Change the copy settings for the current job You can customi ze the copy settings of the HP All-in-O ne to handle nearl y any copy task.
To set the paper size from the control pan el 1. Press Copy Menu . The Copy Menu appears. 2. Press to highlight Paper Size , and then press OK . The Paper Size menu appea rs.
Paper type Control panel setting HP Premium Plus Photo Paper, Glossy Premium Photo HP Premium Plus Photo Paper, Matte Premium Photo HP Premium Plus 10 x 15 cm (4 x 6 inch) Photo Paper Premium Photo HP.
3. Press Copy Menu . The Copy Menu appears. 4. Press to highlight Quality , and th en press OK . The Quali ty menu appears. 5. Press to select a copy quality. 6. Press OK . Adjust the lightness an d darkness of your copy You can use the Lighter/Darker option to adjust t he contrast of the copies you make.
This section contains the foll owing topics : • Make a bord erless copy of a photo • Resize an original t o fit onto letter or A4 paper • Resize an original u sing custom settings • Crop an or.
Resize an original to fit onto letter or A4 paper You can use the Fit to Page feature to copy an original to fit withi n the printable margins of a page withou t the risk of cropping some part of your orig inal. This is useful for red ucing or enlarging an origina l.
6. Press or to select a percentage to reduce or enl arge the copy. (The minimum and maximum percentage to resize a copy varies by model.) 7. Press OK . Crop an original After changing se ttings on the HP All-in-O ne for making a copy, you can use the crop feature to spe cify a particular area of the ori ginal to copy.
The Mixed enhancement is the default option. Use the Mixed enhancement to sharpen edges of most ori ginals. You can use Photo enhancements to enhance light colors th at might otherwi se appear white.
Chapter 10 94 Use the copy features Copy.
11 Print reports and forms The HP All-in-One enabl es you to print self-test reports. You can also print forms such as ruled papers and checklists. This section contai ns the following topics: • Pri.
Print forms The HP All-in-One con tains built-in templates that enab le you to print common forms, such as narrow or wide ruled notebook paper, graph paper, task checklists, and music sheets on plain lett er- or A4-size paper. To print forms from the control panel 1.
12 Maintain the HP All-in-One The HP All-in -One requires l ittle maintena nce. Sometimes you mi ght want to clean the glass and lid backing to re move surface dust and ensure tha t your copies and scans remain clear. You will also ne ed to replace ink cartridges, clean the print head assembly, or align the print er from time to time.
Clean the l id backing Minor debris can accumulate on the white document backing locate d underneath the lid of the HP All-in-O ne. To clean the lid b acking 1. Turn off the HP All -in-One, and raise the lid. 2. Clean the whi te document backing with a so ft cloth or sponge slightly moiste ned with a mild soap and warm water.
3. Press to highlight Display In k Gauge , and then press OK . The HP All-in-On e displays a gauge that shows t he estimated ink levels of a ll cartridges installed. 4. Press any bu tton to return t o the Tools menu. To check the ink leve ls from the HP Photosmart Software 1.
NOTE: If you are in stalling ink cartridges in th e HP All-in-O ne for the first tim e, be sure to use only the ink cartridges th at came with the device. The ink in these cartridges is specially f ormulated to mix with the ink in the pri nt head assembly at first- time setup .
If you are replacing one of the five color ink cartridges, such as yellow, light cyan (blue), cyan, li ght magenta (pink), or magent a, lift the appropriate lat ch in the center area. 1 Ink cartridge latch for the black ink cartridge 2 Ink cartridge latches for the color ink cartrid ges 4.
5. Remove the new in k cartridge from its packaging, and th en, holding it by the handl e, push the ink cartridge in to the empty slot. Match the color and pa ttern of the ink cartridge to the color and pattern on the pr int carriage. 6. Close the latch and make sure it is secure.
maintenan ce to ensure exce llent print qu ality. You might want to use this featur e when the self-test report shows st reaking or white lines through any of the blocks of color. If you still h ave print quality problems aft er aligning the printe r, try cleaning th e print head.
To clean the print head from the contr ol panel 1. Load letter or A4 un used plain white paper into the input tray. 2. Press Setup . 3. Press to highlight Tools , and then press OK . 4. Press to highlight Clea n Printhead , and then press OK . The HP All-in-One cleans the print head and prints a pa ge that you can recycle or discard.
To clean the ink ca rtridge contacts 1. Make sure the HP All- in-One is turned on. 2. Lift the ink ca rtridge door. 3. Squeeze the bottom of th e latch below the ink cartridge you wan t to clean, and then lift the latch. NOTE: Do not remove mul tiple ink cartridges at the sam e time.
Remove ink from your sk in and clothing Follow these instructio ns to remove ink from your skin and clothi ng: Surface Remedy Skin Wash the area with an abrasive soap. White fabric Wash the fabric in co ld water and use chlorine bleach. Color fabric Wa sh the fabric in cold water and use sudsy a mmonia.
13 Shop for ink supplies For a list of ink cartrid ge numbers, see the printed documentati on that came with the HP All-in-One . You can also use the software that came wi th the HP All-in-One to find out the reorde r number for all the ink cartridges.
Chapter 13 108 Shop for ink supplies Shop for ink supplies.
14 Troubleshooting This section contai ns the following topics: • Troubleshootin g tips • Hardware setup troubleshooting • Software instal lation troubleshoot ing • Network tr oubleshooting .
sure the other end o f the USB cable is plugged into a USB port on your computer. After the cable is conn ected properly, turn the HP All-in-O ne off and then on again. • If you are connecti ng the HP All-in-One through a USB hub, make sure the hub i s turned on .
• Do not clean the prin t head unnecessarily. This wastes i nk and shortens the life of the cartridges. • Handle ink cartridges carefu lly. Dropping, jarring, or rough handl ing during installation can cause temporary printing problems. Informat ion on paper The HP All-in-One is d esigned to work well with most paper types.
3. Gently pull the paper out of the rollers. CAUTION: If the paper tears when you are removing it from the ro llers, check the rollers and wheels for torn pieces of paper that might be remaining insi de the device. If you do no t remove all the pieces of paper from the HP All-in-One, more paper jams are likel y to occur.
The HP All-in-One w ill not turn on Cause: The HP Al l-in-One is not properly connected to a power supply. Solution: • Make sure the power cord is fi rmly connected to both the HP All-in-One and th e power adapter. Pl ug the power co rd into a grou nded power outl et, surge protector, or power strip.
I connected the USB cable, but I am having prob lems using the HP All-in-One w ith my computer Cause: The USB cable was connected befo re the software was installed . Connecting the USB cabl e before prompted can cause er rors. Solution: You must first install the software that came with the H P All-in-One before connecting the U SB cable.
Solution: You can change the country/ region settings from the Preferences menu. For more information, see: “ Set your lang uage and country/regi on” on page 15 I received a mess age on the displa.
I received a messa ge on the display about a paper jam o r a blocked print head assembly Cause: The HP All-in-One has a paper jam. Solution: Clear th e paper jam, and then follow th e prompts on the display or the computer screen to continue . For more information, see: “ Clear paper jams” on page 111 Cause: The print head assembly i s blocked.
Solution: Click Details to see what the spe cific problem is, and then correct the problem before attem pting to install the softw are. A red X appears on the USB con nect prompt Cause: Normally , a green check appears indicating that the USB connection is successful.
in-One application fil es from your computer. Make su re to remove them properly using the uninstall util ity provided when you installe d the software that came with the HP All- in-One.
To uninstall from a Wind ows computer, method 2 NOTE: Use this method if Uninstall is not availabl e in the Windows Start menu. 1. On the Window s taskbar, click Start , Settings , Control Panel . 2. Double-click Add/Remove P rograms . 3. Select HP Photosmart All-In-One Driver Software , and then click Change/ Remove .
Solution: Install the HP Photosmart Software that came with the HP All-in-One. If it is installed , restart your computer. To instal l the HP Photosma rt Software 1. Insert the HP All-in-One CD-ROM into your co mputer’s CD-ROM drive and th en start the Setup program.
This section contai ns the following topics: • The computer is unab le to discover the HP All-in-One • The Printer not Found screen appears during instal lation The computer is unabl e to discover the HP All-in-One Cause: Cables are not connected properly.
To establish an a ctive network connection 1. Check the cable connect ions from the HP All-in-One to your gateway, router, or hub to ensure co nnections are secure. 2. If the connectio ns are secure, press the On button on t he control panel to turn the HP All-in-One off.
Solution: Check the following cables to ensure they are connected properly: • Cables be tween the HP All-in-One and the hu b or router • Cables be tween the hu b or router a nd your computer • C.
If the self-test re port shows a defect, tr y the following: • Clean the ink cartridg es automatically. For more information, see “ Clean the print head” on pa ge 103 . • If you are m issing lines when you print, clean the electrical co ntacts.
Solution: If the pap er is too close to the p rint head during printing , the ink might be smeared. This ca n happen if the paper is ra ised, wrinkle d, or very thick, such a s a mailing envelope. Make sure the paper lays flat in the input t ray and is not wrinkled.
NOTE: HP cannot guarantee the quality or reliability of non -HP ink. Printer service or repa irs required as a result of printer failure or d amage attributable to the use of non -HP ink will not be covered under warrant y. The text ed ges are jagged Cause: The font is a custom size.
Solution: Load paper wi th the side you want to print on facing down. For example, if you are loading glossy photo paper, load the paper with the glossy side down. For more information, see: “ Load paper” on p age 36 Cause: You are using non-HP ink.
If the problem persists, use the software you installed with the HP All-in-One or another softwa re application to rotate you r image 180 degrees so tha t the light blue, gray, or brown hues in your im age do not print at the bottom o f the page.
Cause: The Paper Type setting is incorrect. Solution: Change the Paper Type setting to match the type of paper loaded in the input tray. For more information, see: •“ Set the copy paper type” on.
Solution: Chang e the Paper Type sett ing to match the type of paper loade d in the input tray. For more information, see: •“ Set the copy paper type” on pa ge 87 •“ Set the paper type f or printing” on page 47 Cause: The print quality set ting on the HP All-in-One is set too low.
Solution: Make sure the Two -sided printing a ccessory on the back of the HP All- in-One is securely in stalled. Ink is oversprayi ng the paper when I print a photo Cause: A small amount (a fe w millimeters) of overspray is common when maki ng a copy of a photo.
Solution: Remove all paper from the input tray. Load a stack of en velopes in the input tray, with the envelope flaps facing up and t o the left. NOTE: To avoid paper jams, tuck the flaps inside the envelopes. Related topics “ Load envelopes” on page 40 Cause: The wrong type of envelop e is loaded.
Solution: Load paper in the input tray. For more information, see: “ Load paper” on p age 36 Cause: The print head assembly has stal led. Solution: Turn the HP All-in-One off and open the ink cartridge door.
Solution: The printer driver status might have ch anged to eith er offline or stop printing . To check the prin ter driver status 1. In the HP Solution C enter, click the device tab. 2. Click Settings . 3. Click Status . If the status is offline or stop printing , change t he status to read y .
the HP All-in-One a nd plugged into a power outlet. Press the On button to turn on the HP All-in-One. Cause: The HP All-in-One is busy with an other task. Solution: If the HP Al l-in-One is performing another t ask such as copying or scanning, your print job wi ll be delayed until the HP All-in-One comple tes the current task.
Solution: Clear t he paper jam. For more information, see: “ Clear paper jams” on page 111 Cause: The print head assembly h as stalled. Solution: Turn th e HP All-in-One off and open the ink cartridg e door.
Solution: Verify that you have sel ected the proper paper size setting f or your project. Make sure that you ha ve loaded the co rrect paper si ze in the input tray.
Solution: Make sure the l ayout of the document you are t rying to print fits on a pape r size supported by th e HP All-in-One. To preview the print layout 1. Load the correct paper size into the inpu t tray. 2. Preview your prin t job before sending it to the HP All-in-One.
Memory card troubleshooting Use this section to so lve these memory card problems: • My memory card no longer works in my digital camera • The HP All-in-One does no t read the memory card • The .
Solution: Remove one of t he memory cards. You can use only one mem ory card at a ti me. Cause: The fi le system is co rrupted. Solution: Check the display fo r an error messa ge telling you a bout the problem and how to solve it. If the file system on the card is corr upt, reformat the memory card in your digital camera.
Solution: Install the HP Photosmart Soft ware that came with the HP All-in-One. If it is installed, restart your computer. To install the HP Photosmart Software 1. Insert the HP All-in-One C D-ROM into your computer’s C D-ROM drive and then start the Setup pro gram.
The CIFS server is i ncluded in all network-connected H P All-in-One devices. It provides network driv e letter access to the memory card in the HP All-in-O ne. This lets you re ad/write file s on the netwo rk from the mem ory card in the HP All-in-One.
• Text format is incorrect • Text is incorrect or missing • The scan feature does not work Scan halts Cause: The computer system resources might be low. Solution: Turn off the HP All-i n-One and then turn it back on. Tu rn off the computer and then turn it ba ck on.
Solution: Load your origin al print sid e down on the ri ght front corner of th e glass. Scanned image i s incorrectly cropped Cause: The software is set to automatically crop sca nned pictures. Solution: The Autocrop featu re crops anything that is not part of the main image.
Text is incorr ect or missing Cause: The bright ness is not set correctly. Solution: Adjust the brightness, and then rescan the original . Cause: Debris mi ght be stuck on the glass o r on the back of the document lid. This can cause poor-quality scans.
• Parts of the original do not appear or are cut off • Fit to Page is not working as expected • A borderless copy has white space around the edges • The image is croppe d when I make a borderl.
Solution: Clear the paper jam and remove any torn paper that remains in the HP All- in-One. For more information, see: “ Clear paper jams ” on page 111 Parts of the original do not a ppear or are cut off Cause: The origi nal is placed incorrectly on the gla ss.
Solution: Load your origin al print sid e down on the ri ght front corner of th e glass. For more information, see: “ Load orig inals” on page 33 . Cause: Debris mig ht be stuck on the glass or on the b ack of the document li d. The HP All-in-One i nterprets anything it detect s on the glass as part of the image .
The image is croppe d when I make a borderless copy Cause: The HP All-in-One cropped some of the i mage around the margins of t he copy to achieve a borderl ess print without changing the proportions of the original. Solution: If you want to enl arge a photo to fit a full-size p age without cropping th e edges, use Fit to Page .
• Photo tray cannot disengage • Two-sided printing accessory is missing Firmware revisio n mismatch Cause: The revision number of the H P All-in-One firmware does not mat ch the revision numbe r of the software. Solution: To find supp ort and warranty informatio n, go to the HP Web site at www.
tap the stack of paper against a flat surface, and reload the pap er into the photo tray. Follow the pro mpts on the display or the computer screen to continue your print job. Cause: The paper i s not feeding properly o r is loaded incorrectly. Solution: Make sure you have paper load ed correctly in the photo tray.
Solution: Push the output tray all the way down . Two-sided printi ng accessory is missing Cause: The Two-sided printing a ccessory is not installed or it is installed incorrectly. Solution: Firmly insert the Two-sided printi ng accessory into the back of the device until both sid es snap into place .
HP Photosmart Softwar e. The copies mi ght not be damaged. If th ese solutions do not work, reta ke the photo s with your digi tal camera as a last resort.
Cause: The fi le system is co rrupted. Solution: Check the di splay for an error message telling you that the images on t he memory card a re corrupted. If the file system on the card is corr upt, reformat the memory card in your digital camera. CAUTION: Reformatting the memory card will delete any photos stored on t he card.
Solution: Remove all but o ne memory card. The HP Al l-in-One reads the remainin g memory card and displays the f irst photo stored on the memory card. Cause: You have inserted a Compact Flash memory c ard backwards or upsi de down. Solution: Remove the memo ry card and reinsert it correctly.
Solution: Make sure you fully insert the memory card int o the appropriate slot on the HP All-in-O ne, and then try the task ag ain. Card access error Cause: There are two or more memory cards inserted into the HP All-in-One at the same time. Solution: Remove all but one memory card.
If the memory card is not inserted properly, the HP All-in-One will not respond and the Photo light (ne ar the memory card slots) will not turn on. After the memory card has been inserted properly, the Ph oto light will blink for a few seconds, and then remai n lit.
For more information, see: “ Load full-size paper” on page 37 Ink is drying Cause: Transparencies and som e other media require a dryin g time that is longe r than normal. Solution: Leave th e sheet in the output tray until th e message disappears.
Paper mismatch Cause: The print setting for the print job does not ma tch the pape r type or siz e loaded in the HP All-in-One. Solution: Change the print se tting or load the appropriate paper in the input t ray.
Solution: If t he HP All-in-One is not properly conne cted to the computer, communication errors can occu r. Make sure the USB cabl e is securely connected to the HP All-in-O ne and the computer, as shown be low.
Improper shutdown Cause: The last time the HP All -in-One was used, it was not tu rned off properly. If the HP All-in-One is turned off by turning off the switch on a pow er strip or by using a wall switch, the device can be damaged. Solution: Press the On button located on th e control panel of th e HP All-in-One to turn the device on an d off.
• Ink cartridge pr oblem • Ink cartridge(s) are empt y • Ink cartridge(s) are expired • Ink delivery failure • Ink expiration near • Ink supply error • Non-HP ink • Original HP in k de.
Cause: The ink ca rtridge(s) are not intended for use in this device. Solution: Contact HP supp ort. Go to: www.hp.com/support If prompted, choose your country/region , and then click Co ntact HP for information on calling for techni cal support.
•“ Ink cartridge warran ty information” on page 169 •“ Shop for ink supplies” on page 107 Ink cartridge(s ) are empty Cause: The indicated ink cartridge(s) are out of ink. Solution: Replac e the indicated ink cartridge(s) wit h new ink cartridge(s).
Each ink cartridge has an expirat ion date. The purpose of expiratio n is to protect the printing system and t o ensure ink quality. When you receive an ink cartridge(s) are expired message, re move and replace the expired ink cartridge, and then close the message.
HP recommends that you use genuine HP ink cartridg es. Genuine HP ink cartridges are designed a nd tested with HP printe rs to help you easily pr oduce great results, time after time. NOTE: HP cannot guarantee the quality or reliability of non -HP ink.
Alignment failed Cause: An incorrect type of paper is loaded in the input t ray. Solution: If you have color o r photo paper loaded in the in put tray when you align the printer, the a lignment might fail. Load unused plain white le tter or A4 paper into the input t ray, and then tr y the alignment again.
To resolve this error, replace the affected ink cartridge(s) with the i nk cartridges that were shipped with th e HP All-in-One. For more information, see: “ Replace the ink cartridges” on page 99 Ink cartridge is mi ssing, incorrectly instal led, or not intended for your devic e Cause: One or more ink cartridges are missin g.
15 HP warranty and support Hewlett-Packard provides Internet and phone su pport for the HP All-in-One. This section contains the following topics: • Warranty • Ink cartridge warranty information .
Support process If you have a problem, follow these steps: 1. Check the documentation that came with the HP All-in-One. 2. Visit the HP online support Web site at www.
HP support by phone For a list of support phone numbers, see the pr inted documentation that came with the device. This section contains the following topics: • Phone support period • Placing a ca.
HP Quick Exchange Service (Japan) For instructions on how to pack your device for exchange, see “ Pack the HP All-in-One” on page 174 . HP Korea customer support Chapter 15 172 HP warranty and sup.
Prepare the HP All-in-One for shipment If, after contacting HP support or returnin g to the point of purchase, you are requested to send the HP All-in-One in for service, make sure you remove and keep.
4. Retain the control panel faceplate. Do not return the control panel faceplate with the HP All-in- One. CAUTION: The replaceme nt HP All-in-One might not come w ith a control panel faceplate. Store your control panel faceplate in a safe place, and when the replacement HP All-in-One arrives, reattach your control pane l faceplate.
16 Technical information The technical specifications and international r egulatory information for the HP All-in-One are provided in this section. For additional specifications, see the printed do cumentation that came with the HP All-in-One .
Print specifications • Up to 1200 x 1200 rendered dpi black when printing from a computer • Up to 4800 x 1200 optimized dpi color when printing from a compu ter and 1200-input dpi • Print speeds.
• HP inkjet supplies recycli ng program • Energy Star® notice • Special handling of materials • Attention California users • Battery disposal in the Netherlands • Battery disposal in Taiw.
Special handling of mate rials This HP product contains a lithium-manganese diox ide battery lo cated on the main printed circuit assembly that may require s pecial handling at en d-of-life. Attention Californ ia users The battery supplied with this product may contai n perchlorate material.
Disposal of waste equipmen t by users in priv ate households in the European Union Disposal of Waste Equipment by Users in Private Households in the European Union This symbol on the pr oduct or on its packaging indicates that this pr oduct must not be disposed of with y our other household wa ste.
This section contains the following topics: • Regulatory model identification number • FCC statement • Notice to user s in Korea • VCCI (Class B) compliance statement fo r users in Japan • N.
Notice to user s in Korea VCCI (Class B) compl iance statement for users in Japan Notice to users in Ja pan about the power cord Noise emis sion statement fo r Germany Geräusc hemission LpA < 7 0 dB am Arbeitsplatz im Nor malbetrieb nac h DIN 45 6 35 T .
Declarat ion of confor mity (Europe an Economic Are a) The Declaration of Conformity in this documen t complies with ISO/IEC 17050-1 a nd EN 17050-1. It identifies the product, manufacturer’s name and addr ess, and ap plicable spec ifications recognized in the European community.
Index Symbols/Numerics 10 x 15 cm photo paper copy 86 load 38 specifications 175 2 pages on 1, print 57 4 pages on 1, print 57 4 x 6 inch (10 x 15 cm) borderless photos print 53 4 x 6 inch photo paper copy 86 4 x 6 inch photo paper, load 38 802.
default settings, restore 23 device no response 132 not found 160 direction pad 8 disconnected error 155 Display icons 8 display change language 114 change measurements 114 sleep state 9 DNS server (802.
lighten copies 89 link configuration 28 speed 24 load 10 x 15 cm photo paper 38 4 x 6 inch photo paper 38 A4 paper 37 envelopes 40 full-size paper 37 greeting cards 42 Hagaki 39 index cards 39 iron-on.
preview image, edit 82 preview print job 50 print 2 or 4 pages on 1 57 addresses 60 blank printout 138 booklet 56 borderless fails 132 borderless photos 53 both sides of page 55 cancel job 62 CD/DVD l.
settings country/region 15 language 15 network 22 restore defaults 23 setup button 7 menu 10 sharing 22 shift left margin 92 ship your device 173 sleep state 9 smeared ink, fax 124 software applicatio.
188 Index.
デバイスHP (Hewlett-Packard) C6200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) C6200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) C6200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) C6200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) C6200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) C6200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) C6200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) C6200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) C6200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
