HP (Hewlett-Packard)メーカーLH 3の使用説明書/サービス説明書
ページ先へ移動 of 42
HP NetServer LH 3/LH 3r to LH 4/LH 4r Upgrade Guide HP Part Num ber 5967-5271 Printed November 1998 Revision A, December 2000.
ii Notice The information contained in this do cument is subject to change without notice. Hewlett-Packard m ak es no warranty of any k ind with regard to this m aterial, including , but not limited to, the implied warranties of m erchantability a nd fitness for a particula r purpo se .
iii Contents Preface ................................................................................................................... 1 Purpose of T his Guide ....................................................................................... 1 Related Docum entation .
Contents iv 4 Updating Firmware ........................................................................................ 29 Update Sy stem Firm ware ............................................................................ 29 Update the Operating System.
1 Preface Purpose of This Guide This guide describes the steps y ou need to perf orm to conv ert the HP NetServer LH 3 to the HP NetServer LH 4. T his guide includes the follo wing topics: • An intr.
Preface 2 Tools You Need To install this accessory kit, y ou need the f ollowing tools: • An anti-static service kit (3M 8501/8502/8503 or equiv alent ). This kit includes a static-dissipating work su rface, a chassis clip lead, and a w rist strap.
Preface 3 Precautions Follow the procedures listed b elow to ensure safe handling of components and to prevent harm to yourself and the NetServer. WA RNING The HP NetServer L H 3r we ighs u p to 160 pounds (73 k g.
.
5 1 Introduction Installation Ov erview This guid e descr ibes the p roc edure s for insta lling ne w hardware and so ftware in you r LH 4/L H 4r NetServer.
Chapter 1 Introduction 6 CA UTION After the system inform ation upda te, your NetServer will revert to the default NetRAID settings. You mus t restore y our NetRAID c onfigura tion fro m your worksheets o r from note s before y ou can access the NetRA ID arrays.
Chapter 1 Introduction 7 15. Reconfigure the system w ith the Setup and NetRAID utilities, using the configura tion de ta ils you saved in step 2. 16. Verify that the system is restored to its o p erating configuration.
Chapter 1 Introduction 8 Sav ing the Current Operating Environment Before you start the u pgrade, follow th ese instructions to preserv e the current ope r ating enviro nment. CA UTION You must back up all disks on your system - the disk containin g the NOS and an y RA ID arrays.
Chapter 1 Introduction 9 ∗ Cache Policy (Default: Cached I/O) ∗ Virtual Sizing (Default: Disabled) C. SCSI Channel: ∗ Transfer Rate (Default: Ultra-2) 3. If y ou are using th e Integrated Rem ote Assistant features, ru n the Integrated Remote Assistant.
Chapter 1 Introduction 10 Upgrading the Rack (LH 3r) Configuration You can upg rade the LH 3r rack con figuration w ithou t removin g it from the rack, but you m ay find it easier to reinstall the CPU baseb oard and install the chassis reinforcement bars w hen the LH 3r is removed from the rack and sitting on a work bench.
11 2 Removing Cov ers and the CPU Baseboard CA UTION Wear a wrist strap and use a static- dissipating w ork surface connected to the ch assis at all times.
Chapter 2 Removing Covers and the CPU Baseboard 12 Cover 1 Cover 2 Cover 3 LH 3r Cover 1 Co ve r 2 Cover 3 LH 3 Figure 2-1. LH 3 Covers Refer to the HP NetServer LH 3/LH 3r User Guide f or details o f rem oving covers 2 and 3 an d the bezel.
Chapter 2 Removing Covers and the CPU Baseboard 13 Remov ing the LH 3 CPU Baseboard 1. Remove cover 2. 2. Open the CP U b aseboard retaining latches until they point away from the chassis, and the C PU baseboard has come out of its socket. 3. Slide the board out of the chassis (see Figure 2- 2).
Chapter 2 Removing Covers and the CPU Baseboard 14 LH 3r Remove air baffle Remove CPU baseboar d guide LH 3 Remove air baffle Remove CPU baseboar d guide Figure 2-2.
15 3 Installing LH 4 Components WA RNING Do not use m em ory or VRMs f rom th e LH 3/LH 3r C PU baseboard w ith t he LH 4/L H 4r CPU baseboard. This m ay result in damage to components and put data integrity at risk.
Chapter 3 Installing LH 4 Components 16 Figu re 3-2 sh ows t he CPU baseboard parts and slot la yout wit hout th e processors, termin ators, VRMs, mem ory cag e, processor cage, or structural h ardware attached. VRM 1 / Process or 2 Process or 3 2 V R M1 V R M2 VRM 3 / 4 VRM 4 VRM 3 Process or 4 Process or 1 Figure 3-2.
Chapter 3 Installing LH 4 Components 17 Table 3-1. Processor Module and VRM Relationship VRM Name on Baseboard Proc 1 Proc 2 Proc 3 Proc 4 V R M 1 / 2 x xxx V R M 3 / 4 x xxx V R M 1 x xxx V R M 2 xxx.
Chapter 3 Installing LH 4 Components 18 Installing Processors 1. Po sitio n the LH 4 CPU baseb oard, as sho wn in Figure 3-3, on an anti-static mat . 2. Unfasten the two captiv e screws securing the processor cag e cover, then lif t it off and put it aside.
Chapter 3 Installing LH 4 Components 19 Installing Memory CA UTION Memory com es in pack ages of f our DIMMs. Do not install all four DIMMs into one board.
Chapter 3 Installing LH 4 Components 20 Figure 3-5. Removing the Memory Cards 3. Position the mem ory board on a static-dissipating w ork surface and rem ove the DIMMs from their packing materials. 4. Remove a DIMM from its container, handling the m odule by its ends; do not touch the pin s.
Chapter 3 Installing LH 4 Components 21 6. Align the notches on the DIMM with the key s in the slot (see Figure 3-7). Notches Clips Keys LEDs Figure 3-7. Inserting DIMMs into Memory Board 7. Hold the DIMM at a 90-deg ree angle to the sy stem board. 8.
Chapter 3 Installing LH 4 Components 22 10. Replace the boards in th e mem ory cag e. Lower th e ejection levers to lock the board into place in th e cage.
Chapter 3 Installing LH 4 Components 23 Screws secure CPU baseb oard to reinfo rcing bars LH 4r LH 4 Screw s s ecure CPU baseboa rd to reinforc ing bars Figure 3-8.
Chapter 3 Installing LH 4 Components 24 Installing the CPU Baseboard in the Chassis The LH 4 CPU b aseboar d fits into the chassis snugly. Observe these precautions: • Check to m ake sure th at you h ave remov ed the card guide an d air baffle f or the LH 3 CPU basebo a rd .
Chapter 3 Installing LH 4 Components 25 LH 4r Ejection levers Screw s LH 4 Ejection lever s Screw s Figure 3-9. Inserting the LH 4 CPU Baseboard into the Chassis.
Chapter 3 Installing LH 4 Components 26 3. As th e CPU baseboard lowers into place, raise th e levers into a vertical position. When the CP U b aseboard seats in its slo t, push the levers flat to lock the CPU ba seb oard into p osition. 4. Attach the tw o T orx thumbscrew s to secure the CPU b aseb oard to the chassis, as shown in Figure 3-9.
Chapter 3 Installing LH 4 Components 27 Finishing the Hardw are Upgrade As th e last step in the LH 3/L H 3r to LH 4/LH 4r u pgrade, attach the new nam eplate to the top of the f ront surface of the front bezel, as f ollows: 1. Orient the n ameplate so that it can be read correctly w hen attach ed.
.
29 4 Updating Firmw are The HP NetServer Navigator CD-ROM shipped w ith you r upgrad e kit co nta ins new firm ware s pecifically f or the LH 4/LH 4r. Update y our sy stem firm ware n ow as part of the u pgrade procedure. Update Sy stem Firmware 1. Run the HP NetServer Navigator CD-ROM.
Chapter 4 Updating Firmware 30 D. Insert a blank flexible diskette in the NetServer and click to select EXECUT E . The NetServer copies the up date file to the diskette. Label the diskette "NetRAID Firmw are Update" . E. Click <BA CK to return to the NetServer Utilities screen.
Chapter 4 Updating Firmware 31 CA UTION T his Embedded Net RAID u pdate only updates t he firm w are on the C PU baseboard. When y ou reboot t he NOS afte r this update, you will get an error m essage caused by conflicts between the NetRA ID information stored elsewhere in the system and the new inform ation saved in the CP U b aseboard firm ware.
Chapter 4 Updating Firmware 32 1. From directories on the HP NetServer Navigator CD-ROM (for applications that have a uninstall/install o p tion), upda te: ◊ Top Tools Applicat ion ◊ Top Tools Agen ts ◊ PC A ny w he re 2. Follow th ese steps to create a driver diskette to update y our HP drivers: A.
33 5 Warranty and Support The hardw are warran ty below applies to compon ents purchased as accessories. If your com ponent w as factory installed as part of an HP NetServer model, ref er to the w arranty statement prov ided with your sy stem docu men tation.
.
35 A Regulatory Information For regulatory inform ation pertainin g to this HP accessory, please ref er to the regulatory section of th e user gui de for the NetServer in w hich this accessory is installed.
.
37 Index A Accessory kit contents, 7 Air baf fle, 13 An ti-ti p foot, 3, 10 B Backing up disks , 8 Baseboard gu ide, 13 C CAUTION Anti-tip f oot, 10 Chassis reinf orcement bars installing, 22 Contents.
Index 38 Redund ant fan, 2 6 Regulatory information, 35 Related documentation, 1 S Saving the envir o nment, 8 Shock hazard, 3 Software up gr ade , 29 HP NetServer Navigator CD- ROM versi on L.
デバイスHP (Hewlett-Packard) LH 3の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) LH 3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) LH 3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) LH 3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) LH 3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) LH 3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) LH 3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) LH 3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) LH 3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
