HP (Hewlett-Packard)メーカーP2055の使用説明書/サービス説明書
ページ先へ移動 of 14
HP ® LASERJET P2035 • 2055 CAR TRIDGE REMANUF ACTURING INSTRUCTIONS TONER CARTRIDGE HP ® LASERJET P035 • 2055 PRINTER 3232 West El Segundo Blvd., Ha wthorne, California 90250 USA • Ph +1 42 4 675 3300 • Fx +1 424 675 3400 • t echsuppor t@uninetimaging.
REMANUF ACTURING THE HP LASERJET P2035 • 2055 TONER CAR TRIDGE By Mike Josiah Figures abov e show the dif f erent physical sizes of the two cartridges. The car tridges are similar in design to the 1 160/1 320 car- tridges, but are not inter changeable.
SUPPLIES REQUIRED 11 0g HP-P2035 toner f or the CE505A car tridge (2,300 pages) 290g HP-P2035 toner f or the CE505X car tridge (6,500 pages) Replacement Chip New Drum (Optional) Uninet #1 33 72 - HP P 2035, 2055 Unidrum ™ gearless recommended. Wiper Blade (Optional) Dr .
2. Drill a shallow hole on each side of the cartridge as indicated by the arr ows. Figures shown bef ore drilling. Af t er drilling. HP P2035 • 2055 CARTRIDGE REMANUF ACTURING INSTRUCTIONS 3232 West El Segundo Blvd., Ha wthorne, California 90250 USA • Ph +1 42 4 675 3300 • Fx +1 424 675 3400 • t echsuppor t@uninetimaging.
3. Push the pins out with a jew eler’s screwdriver . With the hole in this location by just pushing the scre wdriver in, the pins will be pushed out. Remo ve the pins. 4. Separate the tw o halves. 5. With a flat head screwdriv er , press the drum axle pin out from the inside of the cartridge wall as shown.
The drum hub on the opposite side is w elded. The weld can be brok en or drilled out, but there is a good chance that the hub will either warp if pried off, or will be hard to align if drilled out. 6. Remo ve the drum. This is a good time to look at the ne w drive gear(s).
1 0. Coat the wiper blade with your preferred lubricant. Install the blade and 2 screws. 11 . Re-install the cleaned PCR. Note that a ne w OEM PCR has a small amount of conductive grease on the black (contact) side. 12. Re-Install the OPC Drum and metal axle pin.
13. Slice the two tabs off each location as shown on the left (Seal) end cap. Use a square blade X-Acto knif e to slice off the tabs. NOTE : Both the end caps are plastic welded in place. The only wa y to open them up is to cut the w elds and carefully drill them out.
1 7 . Remo ve the Magnetic roller driv e gear . The end cap will keep the bushing in place. 18. Remo ve the DR. Blade and two scre ws. 19. Clean out an y remaining toner from the hopper . Note the Dr . Blade seal. It is a sticky substance that can be clean with alcohol if toner gets on it.
2 1. If you are going to seal the cartridge, there is a white plas- tic shelf that needs to be remo ved. The shelf is held on with double sided tape. It can be gently pried of f with a small scre w- driver . 22. Re-install the whit e plastic shelf. If the adhesive is not working, replace it with a good double sided tape.
26. Install 2 small screws int o the holes previously drilled out. Leav e the top 3rd hole alone! (This w eld was brok en when the end cap was remo ved). A screw here will int er fere with installing the car tridge in the printer . In our tests, the two screws will hold the end cap on with no pr oblems.
2 7 . Place the tw o halves together , make sure that the two springs are aligned, and insert the two pins. Make sure that the pins are slightly pushed in so that they do not int er f ere with installing the car tridge in the printer . 28. Install the drum cov er; make sure the spring is situat ed correctly.
TROUBLESHOOTING Repetitiv e Defect Char t OPC Drum: 75mm Low er Fuser r oller 63mm Upper F user film 5 7mm Registration r oller 43mm Magnetic Roller 42mm T ransfer roller 39mm PCR 38mm RUNNING TEST P A GES P2030 Series Only T o run the Demo Page, mak e sure that the ready light is on, and briefly press the GO button.
RUNNING THE CLEANING P A GE P2030 Only T o run the Cleaning Page, mak e sure that the ready light is on. Inser t a transparency in the paper tray . Open the printer -driver pr oper ties screen and click on the device settings tab. In the cleaning page area press star t.
デバイスHP (Hewlett-Packard) P2055の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) P2055をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) P2055の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) P2055の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) P2055で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) P2055を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) P2055の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) P2055に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) P2055デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
