HPメーカー377707-002の使用説明書/サービス説明書
ページ先へ移動 of 92
HP 24-Port 4x Fabric Copper Switch Chassis Manager User Guide March 2005 (Second E dition) Part Numb e r 377707-0 0 2.
© Copyright 2005 Hewlett-Pac k ard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Docume ntation, and Technical Data for Commercial Items are license d to the U.
i Contents Preface ....................... ................................... vii Intended Audi ence .............................................................................................................. ...................... vii Typographical C onventions .
ii View Device Status ............................................................................................................. .......................15 3: Chassis Icon Tasks .................................. 17 View Cards on a Chassis .........
iii Assign a SYSLOG Server ......................................................................................................... .... 39 Assign an Authentication Method ..............................................................................
iv Delete Bridge Forwarding ....................................................................................................... ..... 65 View Redundancy Groups .......................................................................................
v Preface This document is a guide to the Chassis Manager W e b-based graphical user inte rface (GUI) that runs on your Server Switch. This document explains how to use Ch assis Manager (CM) and provides the steps that you need to perform to config ure your Server Switch with the GUI.
vi Cont act Information T able 2-1: Customer Con tact Information For the name of your nearest authorized HP reseller: In the United States, call 1-800-345-1518. In Canada, call 1-800-263-5868. Outside the United States and Canada, refer to www . hp.com.
1 1 About Chassis Manager The following sections ap pear in this chapter: • “Introduction” on page 1 • “Anatomy of Chassis Manager” o n page 1 • “Browser Requirements” on page 6 • .
2 Figure 1-1: System Frame • Click the IP address in the IP Address field of the Sys tem frame to open a telnet window that launches a CLI sess ion to the switch. • Click the email address in the Support Contact field to send an ema il message to technical support.
3 Ta b l e 1 - 2 lists and describes the icons in the T ree frame. T ree Frame Branches 1. Click the plus-sign ( ) to expand an icon and display the branches th at you can configure. 2. Click a branch icon ( ) to open the configuratio n options for that branch in the V iew frame.
4 Ta b l e 1 - 4 list s and describes the conf igurable branch es under the Maintenance ic on. Ta b l e 1 - 5 list s and describes the conf igurable branch es under the In finiBand icon .
5 Ta b l e 1 - 6 list s and describes the conf igurable branch es under the Ethernet icon . Ta b l e 1 - 7 list s and describes the conf igurable branch es under the In finiBand icon . Ta b l e 1 - 8 list s and describes the conf igurable branch es under the Help i con.
6 Figure 1-3 displays the table that appears in the V iew frame when you expand the Chassis icon and click the Ports bran ch. Figure 1-3: View F ra m e Browser Requirement s CM supports the following browsers: • Microsoft® Internet Explorer version 6 • Netscape Navigator version 6 • Mozilla version 1.
7 •S o l a r i s •L i n u x.
8.
9 2 Getting S t arted The following sections ap pear in this chapter: • “Preparing Y our Device” on page 9 • “Launching Chassis Manager” on page 1 1 • “Navigating Chassis Manager” on.
10 NOTE: Consult your netw ork administrator for an IP address, subnet mask, and gateway address before you begin t his process. 1. Use the Serial Console port to open a CLI sessi on to your de vice, then log in as a user with administrative access. 2.
11 b. (Optional) Enter the ip http secur e-server command to enable HTTPS services on your device to permit SSL-secured access to your Server Switch. Example Launching Chassis Manager CM without SSL requires no additional setup. CM with SSL requires add itional steps based on yourW eb browser .
12 Net scape/Mozilla T o launch a secure CM connection: 1. Launch your W eb browser . 2. T ype https:// and the IP address of your Server Switch in the address field of your browser and press Enter . (Y ou confi gured the IP address in step 5 of “Preparing Y our Device” on page 9 ) A login window opens.
13 5. Click the root certificate in the tree. Example 6. Click the V iew Certificate butto n. 7. Click the Install Certificate butto n. 8. Click the Next button. 9. Click the Place all certificates in the following stor e radio button. 10. Click the Browse button.
14 The alert cautions you that the na me on the certificate does not match th e name of the site. This hostname mismatch message reappears after you log in and the java applet begins to load. T o avoid this message entirely , configure your Server Switch to u s e the identifier that you enter in the browser to verify certificates.
15 When you further fi lter your display , the V iew frame indicates the new level of granularity . For instance, if you view the ports on a particular gateway card instead of all ports on the device, a tiered locator appears, followed by a filter indicator .
16.
17 3 Chassis Icon T asks The following sections ap pear in this chapter: • “V iewing Cards on a Chassis” on page 17 • “V iew ing Internal Gateway Ports” on page 22 • “V iew ing Physica.
18 Operational S tate Displays the general condition of the interface card. The general condition may appear as any of the following: • unknown • normal • bootFailed • tooHot • booting • checkingBoo tImage • wrongBootImag e • rebooting • standby • recoveryImage A condition of unknown indicates an unsupported interface card.
19 3. (Optional) Click the Refresh button to update the attributes in the display . V iewing Card Properties T o view card properties: 1. Expand the Chassis icon in the Tree frame. 2. Click the Cards branch. A Cards table that includes all car ds in the chassis ap pears.
20 Operational S tate field Displays the general condition of the interface card. The general condition may appear as any of the following: • unknown • normal • wrong-imag e • bootFailed • tooHot • booting A condition of unknown indicates an unsupported interface card.
21 V iewing Card Inventory T o view memory and imag e information on a card: 1. Expand the Chassis icon in the Tree frame. 2. Click the Cards branch. The Cards table appears. 3. Click the radio bu tton next to the card whose inventory you want to view , t hen click the Inventory button.
22 Configuring Administrative S tatus of a Card W ith CM, you can bring up or shut down any card on you r chassis. T o configure th e administrative status of a card: 1. Expand the Chassis icon in the Tree frame. 2. Click the Cards branch. A table of the cards in the chas sis appears.
23 4. From the Show Options... pulldown menu, select Show Gateway Ports . The Gateway Ports table opens in the V iew frame. Ta b l e 3 - 4 lists and describes the fields in this table. V iewing Physical Port s on a Chassis T o view the physical ports o n your device: 1.
24 Ta b l e 3 - 6 lists and describes the elements in the Port Pr operties window of an Ethernet port. Ta b l e 3 - 7 list s and describes the fields in the Port Pr operties window of an FC port. T able 3-6: Ethernet Port Proper ties Window Element s Element Descripti on Port field Displays the port number in slot#/port# not ation.
25 Ta b l e 3 - 8 lists and describes the elements in the Port Pr operties windo w of an IB port. Oper S tatus field Displays up to indicate that the port is physically ready for use, otherwise displays do wn .
26 V iewing Port Bridging Properties T o view the bridge to wh ich a port belongs: 1. Expand the Chassis icon in the Tree frame. 2. Click the Ports branch. A Ports table that includes all cards in the chassis appears. A radio button appears to the left of each table entry .
27 Configuring Port s CM provides dif ferent configuratio n options for each type of port. The options available to each port will appear in the Port Proper ties window . Configuring a Port Name T o configure the adm inistrative name of a port: 1. Expand the Chassis icon in the Tree frame.
28 4. Click the Properties button. The Port Properties window opens. 5. In the Name field of the Port Pr operties wi ndow , ente r a name for the port, then click the Apply button. 6. Click the Close button to close the Port Properties window . Enabling or Disabling a Port T o enable or disable a port: 1.
29 NOTE: Not all hardware platform s include power supply in formation. In such cases, the Power Supplies branch does not appear . 1. Expand the Chassis icon in the Tree frame. 2. Click the Power Supplies branch. The Power Supplies table appears in the V iew frame.
30 V iewing Backplane Information T o view backplane i nformation: NOTE: This feature is not availabl e on all hardware platforms. 1. Expand the Chassis icon in the Tree frame. 2. Click the Backplane branch. The Backplane display appears in the V iew frame.
31 T able 3-16 lists and describes the fields in the Ethernet Management Ports display . T able 3-17 lists and describes the fields in the InfiniBand Management Ports display . Data Bits Data bits valu e to which you must configure y our serial connection.
32.
33 4 Maintenance Icon T asks The following sections ap pear in this chapter: • “Configuring Basic Syst em Information ” on page 33 • “Configuring Date and Time Properties” on page 35 • .
34 V iewing System Information T o view basic system information: 1. Expand the Maintenance icon in the Tree fra m e. 2. Click the System Information branch. The System Information display appears in the V iew frame. Ta b l e 4 - 1 lists and describes the elem ents on this display .
35 Configuring Date and T ime Properties An internal clock runs on your device, but we recommend that you configure your device to access a network time protocol (NTP) server to synchronize you r device with your network. Configuring Date and T ime T o configure the dat e and time of the internal clock on your device: 1.
36 3. (Optional) Click the Refresh button to po ll your switch and u pdate your display to reflect t he most current inventory of your fi le system. Deleting Files in the File System T o delete files from your file system: 1. Expand the Maintenance icon in the Tree fra m e.
37 5. Enter the user ID that logs you into the FTP server in the Remote FTP User Name field. 6. Enter the password logs you into the FTP server in the Remote FTP Password field. 7. Enter the directory path and name of the file on the FTP server in the Remote File Path and Name field.
38 Backing Up Running Configuration File T o save your running configuratio n file: 1. Expand the Maintenance icon in the Tree fra m e. 2. Click the Backup Configuration branch. The Backup Configuration display appears in the V iew frame. 3. Enter a file name in the Save Config uration As fiel d.
39 Enabling or Disabling the FTP Access T o enable FTP transfers to and from your device: 1. Expand the Maintenance icon in the Tr ee frame. 2. Expand the Services sub-icon in the Tree frame. 3. Click the General branch. The System Services display appears in the V iew frame.
40 Configuring HTTP and HTTPS T o configure HTTP and HTTPS services: 1. Expand the Maintenance icon in the Tree fra m e. 2. Expand the Services sub-icon in the Tree frame. 3. Click the General branch. The System Services display appears in the V iew frame.
41 Adding RADIUS Servers T o configure a new RADIUS server on your device: 1. Expand the Maintenance icon in the Tree fra m e. 2. Expand the Services sub-icon in the Tree frame. 3. Click the Radius Servers branch. The Radius Servers table appears in the V iew frame.
42 5. In the Address field, enter the IP address of the server . 6. (Optional) Edit the UDP Port field. The numbers to the right of the fiel d indicate the range of integer values th at this field support s. 7. (Optional) Enter an encryption key in the Encry ption Key field.
43 V iewing POST T est Result s T o view POST test results: 1. Expand the Maintenance icon in the Tree fra m e. 2. Expand the Diagno stics sub-icon in the T ree frame. 3. Click the POST branch. The POST S tatus table appears in the V iew frame. Ta b l e 4 - 7 lists a nd describes the fields in the table.
44.
45 5 InfiniBand Icon T asks The following sections ap pear in this chapter: • “V iew ing Subnet Managers” on page 45 • “V iew ing InfiniBand Services” on page 47 • “V iew ing InfiniBan.
46 V iewing Subnet Manager Properties T o view SM properties: 1. Expand the Inf iniBan d icon in the Tr ee frame. 2. Click the Subnet Managers branch. The Subnet Managers table appears in the V iew frame. 3. Click the radio button next to the SM that you want to view , then click the Properties button.
47 Deleting a Subnet Manager T o delete a SM: 1. Expand the Inf iniBan d icon in the Tr ee frame. 2. Click the Subnet Managers branch. The Subnet Managers table appears in the V iew frame. 3. Click the radio button next to the SM that you want to delete, then click the Delete button.
48 3. Click the radio button next to the service whose pro perties you want to view , then click the Proper ties button. The InfiniBand Service Properties window opens. Ta b l e 5 - 4 lists and describes the fields in this window . V iewing InfiniBand Nodes Both IB switches and IB hosts qualify as IB nodes.
49 Ta b l e 5 - 7 list s and describes the Switch Pr operties fiel ds in this window . Base V ersion Supported base management datagram (MAD) version. Indicates that this channel adapte r , switch, or router supports versions up to and including thi s version.
50 V iewing Node Port s T o view the IB ports on a node in your IB fabric: 1. Expand the Inf iniBan d icon in the T ree frame. 2. Expand the To p o l o g y icon in the IB frame. 3. Click the Nodes branch. The Nodes table appears in the V iew frame. Linear FDB T op Specifies the top of the linear forwarding table.
51 4. Click the radio button nex t to the node who se ports you want to view , then select Show Ports from the Show Options pulldown men u. The InfiniBand Ports display appears in the V iew frame, but lists only the ports that belong to the node that yo u selected.
52 4. Click the radio button next to th e port whose properties you want to view , then click th e Properties button. The T opology Port Prop erties window opens.
53 Link W idth Enabled Enabled link width (bandwidth ). The value is an integer that indicates the enabled link-width sets for this port. The value may be: • 0 (no state change) • 1 (1x) • 2 (4x.
54 Link Speed Active Speed of an active link. Th e value is 1 (2.5 Gbps). Link Speed Enabled Maximum speed the link is capable of handling. The value is 0 (No state change), 1 (2.5 Gbps), or 3 (value derived from link- speed-supported). Neighbor MTU Active maximum transmission unit enabled on th is port for transmit.
55 In Part Enforce Boolean value that indicates whether or not to support opt ional partition enforcemen t for the packets received by this port. There is no default value. Out Part Enfor ce Boolean value that indicates whether or not to support optional partition enforcem ent for the packets transmitted by this port.
56 V iewing Neighboring IB Devices T o view the IB devi ces that di rectly connect to your device: 1. Expand the Inf iniBan d icon in the T ree frame. 2. Expand the To p o l o g y icon in the T ree frame. 3. Click the Neighbors branch in the T ree frame.
57 V iewing IOUs T o view the I/O Units (IOUs) on your device: NOTE: This feature is not availabl e on all hardware platforms. 1. Expand the Inf iniBan d icon in the T ree frame. 2. Expand the Device Management sub-icon in the T ree frame. 3. Click the IOU branch.
58 3. Click the IOCs branch. The IOCs display appears in the V iew frame. T able 5-13 lists and describes the fields in this display . V iewing IOC Properties T o view the pro perties of the I/O controllers (IOCs) on your device: NOTE: This feature is not availabl e on all hardware platforms.
59 V iewing IOC Services T o view the IOC services on your device: NOTE: This feature is not availabl e on all hardware platforms. 1. Expand the Inf iniBan d icon in the T ree frame. 2. Expand the Device Management sub-icon in the T ree frame. 3. Click the IOC Services branch in the T ree frame.
60 4. Click the radio button next to the service whose pro perties you want to view , then click the Proper ties button. The Infiniband Service Properties window opens.
61 6 Ethernet Icon T asks The following sections ap pear in this chapter: • “V iew ing Bridge Groups” on page 61 • “V iew ing Bridge Subnets” on page 64 • “V iew ing Bridge Forwarding.
62 V iewing Bridge Group Properties T o view the pro perties of a bridge group: 1. Expand the Ethernet icon in the T ree frame. 2. Click the Bridge Groups branch. The Bridge Gr oups table appears in the V iew frame. 3. Click the radio button next to the bridg e group whose properties you want to view , then click the Proper ties button.
63 4. Enter a bridge group ID num ber in the ID field. 5. (Optional) Enter a name in the Name field. 6. Enter a subnet prefix in the Subnet Prefix field or leave the field as 0.0.0. 0 to enable auto-detection. 7. Enter the length of the subnet prefix in the Subnet Prefix Len field.
64 V iewing Bridge Subnet s T o view bridge subnets: 1. Expand the Ethernet icon in the T ree frame. 2. Click the Bridge Subnet branch. The Bridge Subnet display appears in the V iew frame. Ta b l e 6 - 3 lists and describes the fields in this display .
65 Adding Bridge Forwarding T o add a bridge subnet: 1. Expand the Ethernet icon in the T ree frame. 2. Click the Bridge Forwarding branch. 3. Click the Add button. The Add Ethernet Bridge Group Forwarding window opens. 4. Enter the ID of the bridge group in the ID field.
66 V iewing T runk Group s T o view the tru nk groups on your Server Switch: 1. Expand the Ethernet icon in the T ree frame. 2. Click the T runk Grou ps branch. The T runk Gr oups table appears in the V iew frame. Ta b l e 6 - 6 lists and describes the fields in this table.
67 6. Check, in the Port Members field, the checkboxes of the por ts that you want to include. NOTE: Check the checkbox of a particular card to automatically check all ports on that card. 7. Click the radio button of the distribution type to apply to the trunk gro up in the Distribution T ype field.
68 Configuring a T runk Group T o configure an existing trunk group: 1. Expand the Ethernet icon in the T ree frame. 2. Click the T runk Grou ps branch. The T runk Gr oups table appears in the V iew frame. 3. Click the radio button next to the group that you want to delete, then click the Pr operties button.
69 7 Fibre Channel Icon T asks The following sections ap pear in this chapter: • “Configuring Global ITL Attrib utes” on page 69 • “V iewing SRP Hosts (Initiators)” on page 70 • “V iew.
70 • Uncheck the checkbox and grant all new initiators access to ports. b. (Optional) Click the Restricted checkbox in the LUN Access field to: • Check the checkbox an d deny all new initiators access to LUNs. • Uncheck the checkbox and grant al l new initiators access to LUNs.
71 V i ewing SRP Host (Initiator) Properties T o view the properti es of a SRP host: 1. Expand the Fibre Channel icon in the Tree frame. 2. Click the SRP Hosts branch. A SRP Hosts table that includes all SRP hosts that connect to the chassis appears in the V iew frame.
72 4. Select Show WWPNs from the Show Options pulldown menu. A SRP H ost Wwpns table appears in the V iew frame. Ta b l e 7 - 3 lists and describes the fields in th is table. V iewing IT Policies of the Host T o view the details of the initiat or-tar get (I T) pairs to which a host (initi ator) belongs: 1.
73 Deleting SRP Host T o delete an SRP host from the confi guration file: 1. Expand the Fibre Channel icon in the Tree frame. 2. Click the SRP Hosts branch. A SRP Hosts table that includes all SRP hosts that connect to the chassis appears in the V iew frame.
74 V iewing Fibre Channel T arget Properties T o view the properties of a Fibre Channel tar get: 1. Expand the Fibre Channel icon in the Tree frame. 2. Click the T argets branch. A T argets table that includes all target s in your configuration file appears in the V iew frame.
75 6. (Optional) Enter a serve name in the Service Name field. 7. Click the Apply button, then click the Close butto n. V iewing IT Policies of the T arget T o view the details of the initiat or-tar get (IT) pairs to which a target belongs: 1. Expand the Fibre Channel icon in the Tree frame.
76 3. Click the radio button next to the LUN wh ose properties you want to view , then click the Proper ties button. The SRP LUN Properties window opens. Ta b l e 7 - 7 li sts and d escrib es the elements in this window . Configuring Fibre Channel LUN Properties T o configure FB LUN properties: 1.
77 9. Click the Apply button, then click the Close butto n. V iewing ITL Policies of the LUN T o view the details of the initiat or-tar get-LUN (ITL) groups to which a LUN belongs: 1. Expand the Fibre Channel icon in the Tree frame. 2. Click the Logical Units branch.
78 V iewing ITLs T o view ITL properties: 1. Expand the Fibre Channel icon in the T ree frame. 2. Click the ITLs branch. The ITLs table appears in the V iew frame. T able 7-10 lists and describes the fields in this table. V iewing ITL Properties T o view detailed ITL properties: 1.
79 V iewing Global St atistics T o view global SRP statistics: 1. Expand the FB icon in the T ree frame. 2. Click the Global S tatistics branch. The SRP Glob al S tatistics display appears in the V iew frame. T able 7-12 lists an d describes th e fields in this displ ay .
80 FCP Commands Completed T o tal number of FCP commands completed on the FB interface gateway(s). FCP Bytes Read T otal number of I/O bytes read by the target device. FCP Bytes Written T o tal number of I/O bytes written by the target device. FCP Commands Outstanding T otal number of FCP commands outstanding on the FB interface gateway(s).
Index A access privileges ....................................................15 admin status configuring, card .............................................22 authentication ........................................................39 auto-negotiation, configuring .
statistics ...........................................................81 H hosts adding ..............................................................74 configuring ......................................................75 deleting ....................
P parity .....................................................................31 PCA assembly number card 21 serial number card 21 port bridging properties ........................................26 ports administrative status ........................
adding ..............................................................67 configuring ......................................................69 deleting ............................................................69 properties ...........................
デバイスHP 377707-002の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP 377707-002をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP 377707-002の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP 377707-002の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP 377707-002で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP 377707-002を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP 377707-002の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP 377707-002に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP 377707-002デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
