HPメーカーLaserJet 1320nwの使用説明書/サービス説明書
ページ先へ移動 of 256
ser v ice hp L ase rJet 116 0 pr int er hp L ase rJet 13 20 ser ie s pr inter.
.
HP LaserJet 1160 printer and HP LaserJet 1320 Series printer Service Manual.
Copyright information © 2004 Copyright Hewlett-Packard Development Company, L.P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained herein is subject to change without notice.
Table of contents 1 Product Information Chapter contents............................................................................................................... ......... 1 Printer configurations.................... ............................
Printer information pages ..................................................................................................... ... 39 Demo page .................. ....................................... .... .................... .............. ......
Electrostatic discharge ................ ................. ..... ............... .................................. ..............82 User-replaceable parts ......................... ..................... .................... ..........................
Print cartridge problems................ .......................................... .................. ......................163 Solving image-quality problems .............. .............................. ............... ..........................163 Clearing jams .
List of tables Table 1-1. Feature designations for HP LaserJet 1320 Series printers.......... .......... ..........2 Table 1-2. Physical specifications.................. .................... ................ ...................... .... .......6 Table 1-3.
viii ENWW.
List of figures Figure 1-1. Front/right-side view........................................................................................... 3 Figure 1-2. Rear/left-side view...................... .................... ...................... ..........
Figure 6-27. Removing the fuser (4 of 10)... .................... ................... ........... ............ ........112 Figure 6-28. Removing the fuser (5 of 10)... .................... ................... ........... ............ ........113 Figure 6-29.
1 Product Information Chapter contents Chapter contents............................................................................................................... ......... 1 Printer configurations.................... .............................
Printer configurations The HP LaserJet 1160 printer is only available in the base configuration. The HP LaserJet 1320 Series printer is available in several configurations. The letters that follow the printer name indicate the differences between the configurations.
HP LaserJet 1160 and HP LaserJet 1320 Series printers base models Figure 1-1. Front/right-side view 1 Wireless light (HP LaserJet 1320nw printer only) 2 Toner light 3 Attention light 4 Ready light 5 G.
Features The following lists describe the features of HP LaserJet 1160 and HP LaserJet 1320 Series printers. HP LaserJet 1160 printer ● 20 ppm (Letter), 19 ppm (A4) ● First page out in as little as 8.
● EconoMode (saves toner) ● The ability to print watermarks, booklets, and multiple pages per sheet (N-up), and to print the first page on different media from the remainder of the document ● 16.
Specifications Physical specifications Table 1-2. Physical specifications Dimensions ● Width: 350 mm (16.8 inches) ● Depth: 352 mm (13.9 inches) ● Height: 256 mm (10.0 inches) Weight (2,500-page cartridge installed) HP LaserJet 1160 printer: 10.
Memory upgrade (HP LaserJet 1320 Series printer only) One DIMM slot available for a 16, 32, 64, or 128 MB RAM DIMM Print resolution ● 1200 dpi : (HP LaserJet 1320 Series printer only) This setting uses ProRes 1200 to provide fine-line detail at 1200 x 1200 dpi.
Electrical specifications WARNING! Power requirements are based on the country/region where the printer is sold. Do not convert operating voltages. Doing so might damage the printer and void the product warranty.
Table 1-9. Electrical specifications, HP LaserJet 1320nw printer Power requirements, 110-127 V models 110-127 V (+/-10%), 50/60 Hz (+/-2) Power requirements, 220-240 V models 220-240 V (+/-10%), 50/60.
NOTE The configuration that was tested to arrive at these values as an HP LaserJet 1320 printer (base model) with its standard tray, using A4 paper and simplex continuous printing. Environmental specifications Table 1-12. Environmental specifications Operating environment Printer plugged into an ac outlet: ● Temperature: 10°C to 32.
Print media specifications HP LaserJet printers produce excellent print quality. The printer accepts a variety of print media, such as cut-sheet paper (including recycled paper), envelopes, labels, transparencies, and custom-size paper.
Hewlett-Packard limited warranty statement HP PRODUCT HP LaserJet 1160 and HP LaserJet 1320 Series printers DURATION OF LIMITED WARRANTY One year from date of purchase HP warrants to you, the end-user.
Hewlett-Packard software license agreement ATTENTION: USE OF THE SOFTWARE IS SUBJECT TO THE HP SOFTWARE LICENSE TERMS SET FORTH BELOW. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE LICENSE TERMS.
Print cartridge limited warranty NOTE The following warranty applies to the print cartridge that came with this printer. This HP product is warranted to be free from defects in materials and workmanship.
HP LaserJet printing supplies In many countries/regions, this product's printing supplies (for example, the print cartridge and fuser) can be returned to HP through the HP Printing Supplies Environmental Program. This easy-to-use and free take-back program is available in more than 30 countries/regions.
Declaration of Conformity statements Declaration of Conformity according to ISO/IEC Guide 22 and EN 45014 Manufacturer's Name: Hewlett-Packard Company Manufacturer's Address: 11311 Chinden B.
Declaration of Conformity according to ISO/IEC Guide 22 and EN 45014 Manufacturer's Name: Hewlett-Packard Company Manufacturer's Address: 11311 Chinden Boulevard Boise, Idaho 83714-1021, USA.
Country/region-specific safety statements Laser safety statement The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has implemented regulations for laser products manufactured since August 1, 1976. Compliance is mandatory for products marketed in the United States.
Laser statement for Finland LASERTURVALLISUUS LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT HP LaserJet 1160, HP LaserJet 1320, HP LaserJet 1320n, HP LaserJet 1320tn, HP LaserJet 1320nw -laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 laserlaite.
20 Chapter 1 Product Information ENWW.
2 Installation Chapter contents Chapter contents............................................................................................................... ....... 21 Operating environment ................... .................. ...................
Operating environment Place the printer on a sturdy, level surface in a well-ventilated area that meets the following environmental requirements: ● Temperature: 15°C to 32.
Printer connections All HP LaserJet 1160 and HP LaserJet 1320 Series printers support USB connections. The base models (HP LaserJet 1160 printer and HP LaserJet 1320 Series printer) also support parallel connections. HP LaserJet 1320n, HP LaserJet 1320tn, and HP LaserJet 1320nw printers also support network connections.
Figure 2-4. Wireless connection, infrastructure mode Figure 2-5. Wireless connection, ad hoc mode 24 Chapter 2 Installation ENWW.
Software The following sections describe the software that is provided with the HP LaserJet 1160 and HP LaserJet 1320 Series printers. Supported operating systems For easy printer setup and access to the full range of printer features, HP strongly recommends that you install the software provided.
Printer drivers A printer driver is the software component that provides access to printer features and provides the means for the computer to communicate with the printer.
The embedded Web server is available for the HP LaserJet 1320 Series printer over the Internal HP Jetdirect network connection. With the embedded Web server, you can gain access to the printer setting.
c. Double-click Print Center or Printer Setup Utility , depending on the operating system. 2. Click Add . The Add Printer List dialog box appears. 3. Select one of the following options from the top menu, depending on how the computer and the printer are connected: ● USB ● TCP/IP : For connecting to your TCP/IP printer in OS X V10.
c. Double-click Print Center or Printer Setup Utility , depending on the operating system. 2. Click Add . The Add Printer List dialog box appears. 3. Select one of the following options from the top menu, depending on how the computer and the printer are connected: ● USB ● TCP/IP : For connecting to your TCP/IP printer in OS X V10.
30 Chapter 2 Installation ENWW.
3 Operation Chapter contents Chapter contents............................................................................................................... ....... 31 Printer control panel .............................................................
Printer control panel The printer control panel is comprised of four lights and two buttons. The HP LaserJet 1320nw printer has an additional light at the top of the control panel.
Status-light patterns Table 3-1. Light status legend Symbol for "light off" Symbol for "light on" Symbol for "light blinking" Table 3-2.
Light status State of the printer Action Reconfiguration Initialization During the printer start up, you can request special initialization sequences that reconfigure the printer. When one of the sequences is requested, such as a cold reset, the lights cycle as in the Initialization/Startup state.
Light status State of the printer Action Job Cancel Pressing the G O button has no effect. After the cancellation process is complete, the printer returns to the Ready state.
Light status State of the printer Action Fatal Error Turn off the printer, wait 10 seconds, and turn on the printer. See Troubleshooting Accessory Error (HP LaserJet 1320 Series printer only) To see additional error information, press the G O button. The light pattern changes.
Light status State of the printer Action Toner Low The toner supply in the cartridge is running low. The Go, Ready, and Attention lights act independently of the Toner Low state. It is necessary to purchase a new print cartridge. Replace the print cartridge when the print on the page begins to fade.
Light status State of the printer Action Wireless Disabled The Go, Ready, Attention, and Toner lights act i ndependently of the Wireless light. No action is necessary. Attempting to Establish Wireless Connection The Wireless light blinks at one- half second intervals.
Printer information pages Special pages reside within the memory of the printer. These pages help you to diagnose and solve problems with the printer. Demo page The Demo page contains examples of text and graphics. To print the Demo page, press and immediately release G O when the printer is ready (the Ready light on) and not printing.
Using the HP Toolbox The HP Toolbox is a Web-based program that you can use for the following tasks: ● Check the printer status. ● Configure the printer settings.
To view the HP Toolbox on Macintosh systems 1. Double-click the hard-drive icon on the desktop. 2. Click Applications , and then click Utilities . 3. Double-click hp toolbox .
Alerts tab Use the Alerts tab to configure the printer to automatically notify you of printer alerts. The Alerts tab has links to these main pages: ● Set up status alerts ● Set up e-mail alerts .
Information tab The Information tab provides quick links to the following information: ● Device status ● Device configuration ● Supplies status ● Event log ● Print Info pages Settings tab The Settings tab has links to several pages that allow you to view and change the printer's configuration.
Using the embedded Web server The embedded Web server can be directly accessed on the HP LaserJet 1320n, HP LaserJet 1320tn, and HP LaserJet 1320nw printers. The embedded Web server provides the same functions as the Advanced Printer Settings section of the HP Toolbox.
Information tab The Information tab consists of the following pages: ● Device Status . This page shows the printer status and shows the life remaining for HP supplies. This page also shows product information such as the network name, network address, and model information.
Other links This section contains links that connect you to the Internet. You must have Internet access in order to use any of these links. If you use a dial-up connection and did not connect when you first opened the embedded Web server, you must connect before you can visit these Web sites.
Wireless printing Wireless networks offer a safe, secure, and cost-effective alternative to traditional wired network connections. The HP LaserJet 1320nw printer has built-in wireless connectivity.
48 Chapter 3 Operation ENWW.
4 Maintenance Chapter contents Chapter contents............................................................................................................... ....... 49 Replacing the print cartridge........................... ........................
Replacing the print cartridge Use the below instructions to remove or replace the print cartridge. To replace the print cartridge 1. Open the print-cartridge door, and remove the print cartridge. CAUTION To prevent damage, do not expose the print cartridge to light.
Cleaning the printer Clean the outside of the printer with a clean, damp cloth when necessary. WARNING! Before cleaning the printer, turn the printer off, unplug the power cord, and wait for the printer to cool. CAUTION Do not use ammonia-based cleaners on or around the printer.
2. Using a dry, lint-free cloth, wipe any residue from the media path area and the print cartridge cavity. 3. Replace the print cartridge, and close the print-cartridge door.
Cleaning the printer media path If you are experiencing toner specks or dots on the printouts, clean the printer media path. This process uses a transparency to remove dust and toner from the media path. Do not use bond or rough paper. NOTE For best results use a sheet of transparency.
Changing the pickup roller Normal use with good media causes wear. The use of poor media might require more frequent replacement of the pickup roller. If the printer regularly mispicks (no media feeds through), you might need to change or clean the pickup roller.
3. Remove tray 2. 4. Open the front automatic two-sided-printing path door (HP LaserJet 1320 Series printer only). 5. Place the printer on the work surface with the front of the printer facing up.
6. Pull the white tabs outward, and rotate the tabs up. 7. Slide the right tab to the right, and leave the tab in this position throughout the procedure.
8. Slide the pickup roller assembly to the right, and remove the left end cap. 9. Remove the pickup roller. ENWW Changing the pickup roller 57.
10. Insert the left side of the new pickup roller into the left slot (1), and insert the right side (with notches in the shaft) into the right slot (2).
15. Close the front automatic two-sided-printing path door. 16. Reinstall the print cartridge, and close the print-cartridge door. 17. Plug the power cord into the printer and then turn on the printer.
Cleaning the pickup roller If you want to clean the pickup roller rather than replace it, follow these instructions: 1. Remove the pickup roller as described in steps 1 through 9 of Changing the pickup roller . 2. Dab a lint-free cloth in water, and scrub the roller.
Changing the printer separation pad Normal use with good media causes wear. The use of poor media might require more frequent replacement of the separation pad. If the printer regularly pulls multiple sheets of media at a time, you might need to change the separation pad.
3. Remove the screws. 62 Chapter 4 Maintenance ENWW.
4. Remove the separation pad. NOTE Before you proceed to step 4, examine the position of the separation pad in the tray. 5. Insert the new separation pad.
6. Replace the screws. 64 Chapter 4 Maintenance ENWW.
Cleaning the printer separation pad If you want to clean the separation pad rather than replace it, follow the instructions below. 1. Remove the separation pad as described in steps 1 through 4 of Changing the printer separation pad . 2. Dab a lint-free cloth in water, and scrub the separation pad.
66 Chapter 4 Maintenance ENWW.
5 Theory of operation Chapter contents Chapter contents............................................................................................................... ....... 67 Introduction............. .................... .............. ...........
Introduction This chapter presents an overview of the relationships between major components in the printer, and includes a detailed discussion of the image-formation system. The following systems are discussed: ● Engine control system ● Laser/scanner system ● Pickup/feed/delivery system ● Image-formation system Figure 5-1.
Internal components Figure 5-2. Cross-section of printer highlights the major internal components. Figure 5-2. Cross-section of printer 1 Top output bin delivery roller 2 Fuser film 3 Laser/scanner 4 .
Timing Sequence of operation Operation sequences are controlled by the microprocessor on the dc controller. Table 5-1. Sequence of operation describes engine operations for each period of a print operation.
Step Action 8 High-voltage control Detect presence of a print cartridge Clean the transfer roller after the primary charging ac bias is turned on 9 Failure/abnormality check: detect laser/scanner failure, fuser failure, and open covers 10 Communication with the memory tag Table 5-2.
Engine control system The engine control system coordinates all printer functions, according to commands sent from the formatter. It drives the laser/scanner system, the image-formation system, and the pickup/feed/delivery system. The engine control system contains the following components: ● Dc controller ● High-voltage PCA Figure 5-3.
Figure 5-4. To be written ENWW Engine control system 73.
Laser/scanner system The laser/scanner system receives video signals from the dc controller and the formatter and converts the signals into latent images on the photosensitive drum.
Pickup/feed/delivery system The pickup/feed/delivery system consists of several types of feed rollers and sensors. The dc controller uses two motors and two solenoids to drive the rollers. Three media-detection sensors detect media as it passes through the printer.
● PS915, fuser delivery sensor ● PS915, duplex sensor (HPLJ 1320 only) Figure 5-6. Pickup/feed/delivery system 76 Chapter 5 Theory of operation ENWW.
Image-formation system Laser printing requires the interaction of several different technologies, including electronics, optics, and electrophotographics, to provide a printed page. Each process functions independently and must be coordinated with the other printer processes.
Step 3: Developing The developing cylinder comes in contact with the photosensitive drum to deposit toner onto the electrostatic latent image. NOTE The charges on the exposed area of the drum are shown as positive in Figure 5-9. Developing . The charges are actually negative, but they are more positive than the charges on the developing cylinder.
The elasticity of the print media causes its separation from the photosensitive drum. A static charge eliminator aids separation by weakening any electrostatic adhesion.
The cleaning blade scrapes the residual toner off of the photosensitive drum and deposits it into the waste toner case. Figure 5-13. Drum cleaning 80 Chapter 5 Theory of operation ENWW.
6 Removal and replacement Chapter contents Chapter contents............................................................................................................... ....... 81 Introduction ............ ..................... .....................
Introduction This chapter documents removal and replacement of field replaceable units (FRUs) only. Removal and replacement strategy Replace parts in the reverse order of their removal. Directions for difficult or critical replacement procedures are included.
Before performing service Follow the pre-service procedures before you perform service. Pre-service procedures 1. Remove all media from the product. 2. Place the product on an ESD mat. If an ESD mat or an ESD-protected workstation is not available, discharge body static and ground the product chassis before servicing the product.
Covers Left-side cover 1. Open the print-cartridge door. 2. Release two tabs (callout 1) to pry the cover away at the back of the printer approximately 38 mm (1.5 inches). NOTE A screwdriver is required to remove the left-side cover from an HP LaserJet 1160 printer.
3. Slide the cover toward the front of the printer to clear the interlock tab (callout 2). Figure 6-2. Removing the left-side cover (2 of 2) 4. Lift the cover away from the printer.
2. Lift the back of the printer off of the workspace and use a flat blade screwdriver to pry the cover from the tab (callout 1) at the bottom of the printer.
3. Use a flat blade screwdriver to pry the cover at the back of the printer, releasing two internal tabs (callout 2). Figure 6-4. Removing the right-side cover (2 of 2) 4. Lift the cover away from the printer. Back cover 1. Remove the left-side cover (see Left-side cover ) and the right-side cover (see Right-side cover ).
2. Remove four screws (callout 1). Figure 6-5. Removing the back cover (1 of 2) 3. Tip the printer so that it rests on its front. 4. Release the tab (callout 2) at the back of the printer on the right side of the printer.
5. Slide the cover toward the right side of the printer to clear the tab (callout 3) on the duplex tray. Figure 6-6. Removing the back cover (2 of 2) 6.
Reinstallation tip Make sure that the flag (callout 1) and both of the fuser-release levers (callout 2) fit through the holes in the cover before attaching the cover.
3. Slide the duplexer tray toward the right side of the printer to release the tab (callout 2) at the back, left side. Figure 6-8. Removing the duplexer tray Top cover 1. Remove the left-side cover (see Left-side cover ), the right-side cover (see Right-side cover ), the back cover (see Back cover ), and the duplexer tray (see Duplexer tray ).
2. Remove two screws (callout 1) at the back of the printer. Figure 6-9. Removing the top cover (1 of 3) 92 Chapter 6 Removal and replacement ENWW.
3. Remove one screw (callout 3) at the left side of the printer and remove one screw (callout 4) from the front of the printer. Figure 6-10. Removing the top cover (2 of 3) ENWW Covers 93.
4. Lift up the left side of the top cover and release the control-panel cable (callout 5) at the right side. Figure 6-11. Removing the top cover (3 of 3) 5.
Control panel 1. Remove all covers (see Covers ). 2. Press a flat blade screwdriver into the gap at the control panel, and then use the screwdriver to pry the control panel out of the top cover.
3. Use a flat blade screwdriver to press the securing tab, and then slide the blade under the control-panel PCA to lift it out. Figure 6-13. Removing the control panel (2 of 2) 4. Slide the control-panel PCA toward the back of the top cover to clear the tab at the front, and then lift the control-panel PCA out of the top cover.
Formatter 1. Remove the left-side cover (see Left-side cover ). 2. Disconnect one flat, flexible cable (callout 1) at the bottom of the formatter. CAUTION Do not fold flat, flexible cables. Also, do not straighten pre-folds in flat, flexible cables. 3.
Laser/scanner 1. Remove all covers (see Covers ). 2. Disconnect one flat, flexible cable (callout 1) from the laser/scanner PCA. 3. Disconnect one cable (callout 2) from the top of the laser/scanner. 4. Unthread all cables (callout 3) from the laser/scanner.
Memory-tag-reader assembly 1. Remove all covers (see Covers ). 2. Remove the fan from the printer chassis (see steps 3 and 4 of Fan ). 3. Remove one cable (callout 1) from the cable-holder on top of the memory-tag-reader cover. 4. Disconnect one cable from the formatter (callout 2).
5. Remove one screw (callout 3). 5 4 3 Figure 6-16. Removing the memory-tag-reader assembly (2 of 2) 6. Lift up slightly the back of the memory-tag-reader assembly and then slide the assembly toward the back of the printer, to release it from the laser/scanner plate.
Duplex-drive PCA 1. Remove all covers (see Covers ). 2. Disconnect the duplex-drive cable (callout 1) at the ECU and route the cable through the hole in the chassis. 1 Figure 6-17. Removing the duplex-drive PCA (1 of 2) 3. Disconnect one cable (callout 2) from the duplex-drive PCA.
4. Remove one screw (callout 3) and then lift the duplex-drive PCA off of the printer. Figure 6-18. Removing the duplex-drive PCA (2 of 2) 102 Chapter 6 Removal and replacement ENWW.
Fuser Several parts must be removed before you can remove the fuser. The following parts are included in this section about removing the fuser: ● Fan ● Duplex-drive gears/face-down gears ● Duplex solenoid ● Fuser Fan 1. Remove all covers (see Covers ).
4. Unhook the fan clip (callout 3) and then lift the fan off of the printer. Reinstallation tip Use the fan clip to hold the fan in place before replacing the screws. Duplex-drive gears/face-down gears NOTE HP LaserJet 1320 Series printers contain duplex-drive gears.
3. Remove three screws (callout 1) and then lift the assembly away from the printer. Figure 6-20. Removing the duplex-drive gears/face-do w n gears NOTE The gears are not attached to the gear plate. Carefully remove the gear plate and the gears together to prevent them from falling out of the assembly.
Figure 6-21. Duplex-drive gears (HP LaserJet 1320 Series printers) and Figure 6-22. Face- down gears (HP LaserJet 1160 printers) show the differences between duplex-drive gears and face-down gears. For HP LaserJet 1320 Series printers, make sure that you replace the gears as shown in Figure 6-21.
Figure 6-22. Face-dow n gears (HP LaserJet 1160 printers) Duplex solenoid (SL3) (HP LaserJet 1320 Series printers only) 1. Remove all covers (see Covers ). 2. Remove the fan (see Fan ). 3. Remove the duplex-drive gears (see Duplex-drive gears/face-down gears ).
5. Remove one screw (callout 2) and lift the solenoid off of the printer chassis. Figure 6-23. Removing the duplex solenoid Fuser 1. Remove all covers (see Covers ). 2. Remove the fan (see Fan ). 3. Remove the duplex-drive gears or face-down gears (see Duplex-drive gears/face-down gears ).
6. Disconnect one cable (callout 2) on the right side of the printer. Figure 6-24. Removing the fuser (1 of 10) ENWW Fuser 109.
7. Disconnect four cables (callout 3) from the ECU, and then disconnect two more cables (callout 4) that were behind the first set. Figure 6-25. Removing the fuser (2 of 10) 8. Pull the tab on the cable holder (callout 5) at the left side of the printer and slide it toward the center to release it from the frame, and then unroute the cables.
9. Pull the tab on the cable holder (callout 6) at the right side of the printer and slide it toward the center to release it from the frame, and then unroute the cables.
10. Disconnect three cables (callout 7). Figure 6-27. Removing the fuser (4 of 10) 112 Chapter 6 Removal and replacement ENWW.
11. Pull the cable holder (callout 8) straight back to remove it, and then unroute the cables. Figure 6-28. Removing the fuser (5 of 10) Reinstallation tip You might find it easier to reassemble the cables and the cable holder if you put the smaller cables back into place first.
12. Disconnect one cable (callout 9) and then unroute the cable from the cable guide. Figure 6-29. Removing the fuser (6 of 10) NOTE Before you proceed to step 13, make sure that all cables disconnected in previous steps are free from any cable guides and cable holders.
13. Remove three screws (callout 10) on the right side of the printer. Figure 6-30. Removing the fuser (7 of 10) ENWW Fuser 115.
14. Remove three screws (callout 11) from the left side of the printer. Figure 6-31. Removing the fuser (8 of 10) 116 Chapter 6 Removal and replacement ENWW.
15. At the left side of the printer, pull the printer chassis from the top to spread the printer frame and release the fuser from the frame. Figure 6-32.
16. Pull the fuser out of the printer at an angle so that the delivery roller shaft clears the hole (callout 12) in the chassis. Figure 6-33. Removing the fuser (10 of 10) 118 Chapter 6 Removal and re.
Interlock assembly NOTE If a wireless communications card is installed in the printer, see Wireless communications card for information about removing the wireless communications card before you remove the interlock assembly. 1. Remove all covers (see Covers ).
5. Disconnect two cables (callout 3). 3 Figure 6-35. Removing the interlock assembly (2 of 2) 120 Chapter 6 Removal and replacement ENWW.
ECU 1. Remove all covers (see Covers ). 2. Remove the fan (see Fan ). 3. Remove the duplex-drive gears (see Duplex-drive gears/face-down gears ). 4. Remove the formatter (see Formatter ). 5. Remove the fuser (see Fuser ). 6. Remove the interlock assembly (see Interlock assembly ).
8. Disconnect three cables (callout 2). Figure 6-37. Removing the ECU (2 of 8) 122 Chapter 6 Removal and replacement ENWW.
9. Unroute the cables at the right side of the printer, releasing them from the cable stays (callout 3). Figure 6-38. Removing the ECU (3 of 8) ENWW ECU 123.
10. Remove one screw (callout 4) from the right side of the printer. Figure 6-39. Removing the ECU (4 of 8) 124 Chapter 6 Removal and replacement ENWW.
11. Remove two screws (callout 5) from the left side of the printer, and then push the interlock cables and the formatter cable (callout 6) through the hole in the chassis.
12. Spread the printer frame at the right side of the printer to release the internal tabs that secure the ECU to the chassis. Figure 6-41. Removing the ECU (6 of 8) 126 Chapter 6 Removal and replacem.
13. Spread the printer frame at the left side of the printer to release the internal tabs, and then lower the ECU slightly and pull it straight back to remove it. NOTE Make sure that cables do not become caught on the contact springs as you remove the ECU.
14. Remove four screws (callout 7) and then lift the ECU off of the ECU plate. Figure 6-43. Removing the ECU (8 of 8) 128 Chapter 6 Removal and replacement ENWW.
Main motor 1. Remove all covers (see Covers ). 2. Remove the fan (see Fan ). 3. Remove the duplex-drive gears (see Duplex-drive gears/face-down gears ). 4. Remove the formatter (see Formatter ). 5. Remove the fuser (see Fuser ). 6. Remove the interlock assembly (see Interlock assembly ).
9. Hold the motor while releasing the tabs (callout 2) on the cable guide, and then lift the motor and the cable guide out of the printer together. Figure 6-45.
Pickup and feed assemblies This section covers the major assemblies of the pickup and feed system: the transfer roller and the registration assembly. For information about replacing the pickup roller, see Changing the pickup roller . For information about replacing the separation pad, see Changing the printer separation pad .
Registration assembly 1. Remove five screws (callout 1). Figure 6-47. Removing the registration assembly 2. Lift the entire assembly out of the printer.
Main gear assembly/tray 2 pickup solenoid 1. Remove all covers (see Covers ). 2. Remove the fan from the printer chassis (see steps 3 and 4 of Fan ). 3. Disconnect one cable (callout 1) at the ECU. Figure 6-48. Removing the main gear assembly (1 of 2) 4.
7. Remove four screws (callout 4). 4 3 2 Figure 6-49. Removing the main gear assembly (2 of 2) 8. Pull the main gear assembly straight away from the printer.
9. To remove the tray 2 pickup solenoid, disconnect one cable (callout 5). 5 Figure 6-50. Removing the tray 2 pickup solenoid (1 of 2) ENWW Main gear assembly/tray 2 pickup solenoid 135.
10. Remove one screw, and then lift the solenoid off of the printer. 6 Figure 6-51. Removing the tray 2 pickup solenoid (2 of 2) 136 Chapter 6 Removal and replacement ENWW.
Print-cartridge door 1. Use a flat blade screwdriver to gently pry the cartridge-door arm off of the print-cartridge door. CAUTION Be careful not to break the tabs.
2. Remove two screws (callout 2). Figure 6-53. Removing the print-cartridge door (2 of 2) 3. Lift the cartridge-door assembly straight away from the printer.
Wireless communications card 1. Remove the left-side cover (see Left-side cover ). 2. Release two tabs (callout 1) that secure the wireless communications card to the interlock assembly.
3. Turn the card over and then disconnect one connector (callout 2). 140 Chapter 6 Removal and replacement ENWW.
7 Troubleshooting Chapter contents Chapter contents............................................................................................................... ..... 141 Basic troubleshooting............ ................ ............. .............
Wired network setup problemsolving .................................................................................... 189 NVRAM initialization............... ...................... ................. ..................... .............. .......... ..
Basic troubleshooting Table 7-1. Basic troubleshooting The printer doesn't turn on. When the product is connected to a correctly grounded power source, the LEDs on the control panel do not light and the main motor does not rotate. Cause Solution No power to the printer.
The printer is unresponsive. The printer turns on and the motor rotates, but none of the control panel lights turn on, and pressing the control panel buttons has no effect. Cause Solution The control panel is defective. Replace the control panel (see Control panel ).
The printer does not print from a computer. The printer prints the engine test and the Demo page, but does not print jobs sent from a computer. Cause Solution The printer driver is not installed correctly. Uninstall and then reinstall the printer software.
Paper-handling problems Choose the item that best describes the problem: ● Paper jam ● Print is skewed (crooked) ● More than one sheet of media feeds through the printer at one time ● Printer .
Printer does not pull media from the media input tray ● Make sure that the printer is not in manual feed mode. See Status light patterns for more information. ● Make sure that the media guides are adjusted properly. ● The pickup roller might be dirty or damaged.
Paper-path troubleshooting Use the following table to solve problems related to moving paper or documents through the product. CAUTION Failure to solve paper-feed problems can result in damage to the printer. Damage resulting from high jam-rates from any of the causes shown in this section can void the printer warranty.
The printer feeds multiple sheets or jams frequently from the main input tray. Cause Solution Paper guides are not adjusted correctly. Slide the guides against the sides of the stack in the main input tray or the priority input slot to center the media.
Printed page is different than what appeared on screen Choose the item that best describes the problem: ● Garbled, incorrect, or incomplete text ● Missing graphics or text, or blank pages ● Page.
Page format is different than on another printer If you used an older or different printer driver (printer software) to create the document or the printer Properties settings in the software are different, the page format might change when you try to print using your new printer driver or settings.
Status light patterns Table 7-3. Light status legend Symbol for "light off" Symbol for "light on" Symbol for "light blinking" Table 7-4.
Light status State of the printer Action Reconfiguration Initialization During the printer start up, you can request special initialization sequences that reconfigure the printer. When one of the sequences is requested, such as a cold reset, the lights cycle as in the Initialization/Startup state.
Light status State of the printer Action Job Cancel Pressing the G O button has no effect. Once the cancellation process has been completed, the printer returns to the Ready state.
Light status State of the printer Action Fatal Error 1. Turn off the printer, wait 10 seconds, and turn on the printer. 2. Unplug the printer for five minutes, and then plug it back in and turn it on. 3. If the printer still has an error, press the G O button and consult the list of secondary messages.
Light status State of the printer Action Toner Low The Go, Ready, and Attention lights act independently of the Toner Low state. Insert a new print cartridge. Toner Missing The print cartridge has been removed from the printer. Reinsert the print cartridge in the printer.
Light status State of the printer Action Wireless Disabled The Go, Ready, Attention, and Toner lights act i ndependently of the Wireless light. No action is necessary. Attempting to Establish Wireless Connection The Wireless light blinks at one- half second intervals.
Fatal error secondary messages If the printer has a fatal error, press and hold the G O button to see a secondary error message. Table 7-5. Fatal error secondary messages Message Cause Solution Engine error. The formatter and engine are not communicating.
Message Cause Solution Beam error 1. Check the laser/scanner cable connections. 2. If the error persists, replace the laser/scanner. Motor error. 1. Check the motor cable connections. 2. If the error persists, replace the motor. Fuser error. The fuser has a malfunction.
Message Cause Solution General fatal error. 1. Turn the printer off, and then turn the printer back on. 2. If the error persists, disconnect the I/O cable and print an engine test. If the self-test is successful, reconnect the I/O cable. 3. If the error persists, replace the formatter.
Accessory error secondary messages If the printer has an accessory error (indicated by all lights blinking), press and hold the G O button to see the secondary error message. Table 7-6. Accessory error secondary messages Message Cause Solution Internal Jetdirect error.
Troubleshooting postscript (PS) errors The following situations are PS language specific and might occur when several printer languages are being used. NOTE To receive a printed or screen displayed message when PS errors occur, open the Print Options dialog box and click the desired selection next to the PS Errors section.
Image troubleshooting Print cartridge problems Checking the print cartridge Image formation defects are frequently the result of problems in the print cartridge. If there is any doubt, always replace the print cartridge before troubleshooting image defects.
Solving print image-quality problems Table 7-8. Solving print image-quality problems Pages do not print or pages are blank. Cause Solution The printer is not plugged in or power switch is off. Make sure that the printer is plugged into a live wall outlet or power strip and that the printer is turned on.
Toner specks appear on the printed page. . Cause Solution The media you are using does not meet HP's specifications (for example, it is too moist or too rough). Make sure that the media meets specifications detailed in the HP LaserJet Printer Family Media Guide .
Vertical black lines appear on the printed page. Cause Solution The photosensitive drum inside the print cartridge is scratched. Replace the print cartridge. The fuser is defective. Replace the fuser (see Fuser ). The printed page has a gray background.
Toner smears appear on the printed page. Cause Solution If the toner smears appear on the leading edge of the media, the media guides are dirty. Wipe the media guides with a dry, lint-free cloth. The media you are using does not meet HP's specifications (for example, it is too moist or too rough).
The toner is loose, and it does not stay attached to the printed page. Cause Solution The fuser temperature is too low. Select Type is: in the Paper/Quality tab of the printer driver. Make sure that it is set for the appropriate media. If the problem persists, replace the fuser (see Fuser ).
Characters are misformed and are producing hollow images. Cause Solution The media is too slick. Try a different media. Make sure that the media meets specifications detailed in the HP LaserJet Printer Family Media Guide . The printer driver is not set for the correct media.
The printed page has curls or waves. Cause Solution The printer is operating in humidity or temperature conditions that are not within the recommended ranges. Move the printer to a different location. The media was in the input tray for too long. Turn the stack of media over and put it back in the tray.
Droplets of water are deposited on the trailing edge Cause Solution Moisture in the printer is condensing on the fuser assembly and dropping onto the media. In excessively hot and humid areas, media retains moisture. Try a different media. Store media in airtight containers to minimize absorption of moisture.
Clearing jams Occasionally, media becomes jammed during a print job. You are notified of a media jam by an error in the software and the printer control panel lights. See Status light patterns for more information. The following are some of the causes of media jams: ● The input trays are loaded improperly or too full.
2. Open the straight-through output door. 3. Rotate the green pressure release levers downward. CAUTION Severe damage to the printer can result from failure to rotate the pressure release levers. Such damage is not covered under the printer warranty. 4.
5. Replace the print cartridge, and close the print-cartridge door. Input trays To clear a jam in the input trays, perform the following steps: CAUTION Do not use sharp objects, such as tweezers or needlenose pliers, to remove jams. Damage caused by sharp objects is not covered by the warranty.
2. Rotate the green pressure release levers downward. CAUTION Severe damage to the printer can result from failure to rotate the pressure release levers. Such damage is not covered under the printer warranty. 3. Open the single-sheet priority input slot (tray 1) door.
5. Close the single-sheet priority input slot (tray 1) door. 6. Open the main input tray (tray 2). 7. With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
8. If no media is visible, open the print-cartridge door, remove the print cartridge, and rotate the upper media guide. Carefully pull the media up and out of the printer. 9. Close the main input tray (tray 2). Output bin CAUTION Do not use sharp objects, such as tweezers or needlenose pliers, to remove jams.
With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer. Straight-through output path To clear a jam in the straight-through output path, perform the following steps: CAUTION Do not use sharp objects, such as tweezers or needlenose pliers, to remove jams.
2. Rotate the green pressure release levers downward. CAUTION Severe damage to the printer can result from failure to rotate the pressure release levers. Such damage is not covered under the printer warranty. 3. With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
Automatic two-sided printing (duplexing) path To clear a jam in the automatic two-sided path, perform the following steps: CAUTION Do not use sharp objects, such as tweezers or needlenose pliers, to remove jams. Damage caused by sharp objects is not covered by the warranty.
3. Remove the main input tray (tray 2). 4. Push down on the green lever on the automatic two-sided path door on the front of the printer. 5. With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
6. Close the automatic two-sided path door. 7. Reinsert the main input tray (tray 2). 8. Open the automatic two-sided path door on the back of the printer.
9. With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer. 10. Close the automatic two-sided path door.
Functional checks This section includes five functional checks for troubleshooting. Engine test The engine test is used to verify that the print engine is functioning correctly. The formatter is bypassed during an engine test, so the engine test is useful for isolating printer problems.
● cleaning stage (removes excess toner from the drum) ● fusing stage (applies heat and pressure to make the image on paper permanent) To perform a half self-test check The purpose of the half self-test check is to determine which process is malfunctioning.
Drum rotation functional check The photosensitive drum, located in the print cartridge, must rotate for the print process to work. The photosensitive drum receives its drive from the main drive assembly. NOTE This test is especially important if refilled print cartridges have been used.
Heating element check Paper passes between the heating element and a soft pressure roller to fuse toner to the paper. 1. Unplug the printer for at least ten minutes. 2. Verify that the thermistor connector is seated into both the printer chassis and the ECU.
High-voltage contacts check The high-voltage contacts in the printer must have a good connection with the contacts on the print cartridge to provide the necessary voltages for the electrophotographic processes.
Wired network setup problemsolving If the computer is unable to discover the HP LaserJet 1320n, HP LaserJet 1320tn, or HP LaserJet 1320nw printer, perform the following steps: 1.
NVRAM initialization CAUTION Only perform the following procedure if absolutely necessary. Performing an NVRAM initialization resets some parameters that cannot be restored later. NVRAM initialization sets all default variables stored in NVRAM back to factory default values or to a default ROM value, depending on the variable.
Cold reset A cold reset changes most system parameters in NVRAM to the factory defaults. However, unlike NVRAM initialization, a cold reset does not reset the page count, the paper tray sizes, language, or formatter number. NOTE A cold reset also resets all the HP Jetdirect settings as well as the printer settings.
Troubleshooting tools and reference diagrams Repetitive image defects If the printer output has a consistent, repetitive defect, then use Table 7-9. Repetitive image defects to determine which part needs to be replaced based on the measured distance between the repetitions of the defect.
General timing chart Figure 7-5. General timing chart ENWW Troubleshooting tools and reference diagrams 193.
Circuit diagram Figure 7-6. Circuit diagram (1 of 2) 194 Chapter 7 Troubleshooting ENWW.
Figure 7-7. Circuit diagram (2 of 2) ENWW Troubleshooting tools and reference diagrams 195.
Solenoids Figure 7-8. Solenoids 1 Duplex solenoid 2 Tray 1 pickup solenoid 3 Tray 2 pickup solenoid 196 Chapter 7 Troubleshooting ENWW.
Switches and sensors Figure 7-9. Switches and sensors 1 Interlock switch 2 Delivery sensor 3 Top-of-page sensor ENWW Troubleshooting tools and reference diagrams 197.
Rollers and pads Figure 7-10. Rollers and pads 1 Transfer roller 2 Pressure roller 3 Pickup roller 4 Separation pad 198 Chapter 7 Troubleshooting ENWW.
8 Parts and diagrams Chapter contents Chapter contents............................................................................................................... ..... 199 Ordering parts and supplies ...............................................
Ordering parts and supplies Parts Order replacement parts from the following Web sites: h30074.www3.hp.com/csn-aux/srvcdlvry/epdo/def ault/ePDOLogin.asp (technicians) h20141.
Consumables and accessories Product name Description Product number Part number Print cartridges UltraPrecise print cartridge 2,500-page print cartridge for the HP LaserJet 1160 printer Q5949A Q5949A .
Product name Description Product number Part number HP Jetdirec t ew 2400 802.11b/g Jetdirect print server J7951A J7951A HP bt1300 Bluetooth Wireless Printer Adapter (both USB and parallel) Jetdirect .
ENWW Consumables and accessories 203.
Assembly locations Figure 8-1. Assembly locations (1 of 2) 204 Chapter 8 Parts and diagrams ENWW.
Table 8-2. Assembly locations (1 of 2) Ref Description Part number Qty 1 Fuser film (Contained in fuser.) N/A 2 Gear assembly, top output bin (HP LaserJet 1160 printers) RM1-1305-000CN 1 2 Duplex-driv.
Figure 8-2. Assembly locations (2 of 2) 206 Chapter 8 Parts and diagrams ENWW.
Table 8-3. Assembly locations (2 of 2) Ref Description Part number Qty 5 Main gear assembly RM1-1299-000CN 1 6 Duplexer (HPLJ 1320) RM1-1313-000CN 1 7 Fuser, 110-127 V RM1-2325-000CN 1 7 Fuser, 220-24.
Covers Figure 8-3. Covers 208 Chapter 8 Parts and diagrams ENWW.
Table 8-4. Covers Ref Description Part number Qty 1 Front cover assembly (HPLJ 1320) RM1-1307-000CN 1 1 Front cover assembly (HPLJ 1160) RM1-1324-000CN 1 2 Rear cover assembly (HPLJ 1320) RM1-1308-000.
Internal assemblies Figure 8-4. Internal components (1 of 4) 210 Chapter 8 Parts and diagrams ENWW.
Table 8-5. Internal components (1 of 4) Ref Description Part number Qty 2 Bushing RC1-3665-000CN 2 3 Guide, dc cable RC1-3731-000CN 1 4 Roller, top output bin RL1-0527-000CN 1 5 Solenoid (SL3) (HPLJ 1.
Figure 8-5. Internal components (2 of 4) 212 Chapter 8 Parts and diagrams ENWW.
Table 8-6. Internal components (2 of 4) Ref Description Part number Qty 1 Holder, fan RC1-3537-000CN 1 4 Cam arm RC1-3544-000CN 1 5 Holder, tag arm RC1-3550-000CN 1 6 Tag arm RC1-3551-000CN 1 13 Holde.
Figure 8-6. Internal components (3 of 4) 214 Chapter 8 Parts and diagrams ENWW.
Table 8-7. Internal components (3 of 4) Ref Description Part number Qty 1 Registration assembly RM1-1281-000CN 1 2 Sensor assembly, top RM1-1283-000CN 1 3 Roller, transfer RC1-3705-000CN 1 501 Screw, .
Figure 8-7. Internal components (4 of 4) 216 Chapter 8 Parts and diagrams ENWW.
Table 8-8. Internal components (4 of 4) Ref Description Part number Qty 1 Motor, dc RK2-0418-000CN 1 2 Solenoid (SL1) tray 2 pickup RK2-0424-000CN 1 3 Power inlet/switch cable assembly RM1-1249-000CN .
Figure 8-8. ECU assembly 218 Chapter 8 Parts and diagrams ENWW.
Table 8-9. ECU assembly Ref Description Part number Qty ECU PCA 110v RM1-1242-000CN 1 ECU PCA, 220v RM1-1243-000CN 1 1 ECU assembly, 110v (HPLJ 1160) RM1-1327-000CN 1 1 ECU assembly, 220v (HPLJ 1160) .
Figure 8-9. Duplex-drive assembly 220 Chapter 8 Parts and diagrams ENWW.
Table 8-10. Duplex-drive assembly Ref Description Part number Qty Duplex-drive assembly (HPLJ 1320) RM1-1302-000CN 1 1 Normal-rotation drive assembly (HPLJ 1320) RM1-1303-000CN 1 2 Reverse-rotation dr.
Figure 8-10. Top output bin gear assembly 222 Chapter 8 Parts and diagrams ENWW.
Table 8-11. Top output bin gear assembly Ref Description Part number Qty Gear assembly, top output bin (HPLJ 1160) RM1-1305-000CN 1 ENWW Internal assemblies 223.
Figure 8-11. Tray 2 assembly 224 Chapter 8 Parts and diagrams ENWW.
Table 8-12. Tray 2 assembly Ref Description Part number Qty Tray 2 (HPLJ 1160) RM1-1322-000CN 1 Tray 2 (HPLJ 1320) RM1-1292-000CN 1 1 Tray 2 cover assembly (HPLJ 1160) RM1-1323-000CN 1 1 Tray 2 cover .
Figure 8-12. Duplexer 226 Chapter 8 Parts and diagrams ENWW.
Table 8-13. Duplexer Ref Description Part number Qty Duplexer (HPLJ 1320) RM1-1313-000CN 1 4 Size-change assembly RM1-1318-000CN 1 ENWW Internal assemblies 227.
Alphabetical parts list Table 8-14. Alphabetical parts list Description Part number Table and page Bushing RC1-3665-000CN Table 8-5 on page 211 Bushing, left RB2-2896-000CN Table 8-5 on page 211 Bushi.
Description Part number Table and page Flag, media sensing RC1-3472-000CN Table 8-5 on page 211 Formatter, HP LaserJet 1160 printer Q3698-67901 Table 8-5 on page 211 Formatter, HP LaserJet 1320 (base).
Description Part number Table and page Power inlet/switch cable assembly RM1-1249-000CN Table 8-8 on page 217 Rear cover assembly (HPLJ 1160) RM1-1325-000CN Table 8-4 on page 209 Rear cover assembly (.
Description Part number Table and page Tag arm RC1-3551-000CN Table 8-6 on page 213 Tray 2 (HPLJ 1160) RM1-1322-000CN Table 8-4 on page 209 Tray 2 (HPLJ 1320) RM1-1292-000CN Table 8-4 on page 209 Tray.
Numerical parts list Table 8-15. Numerical parts list Part number Description Table and page (Contained in fuser.) Fuser film Table 8-2 on page 205 Q3696-67901 Formatter, HP LaserJet 1320 (base) and 1.
Part number Description Table and page RM1-1242-000CN ECU PCA 110v Table 8-9 on page 219 RM1-1243-000CN ECU PCA, 220v Table 8-6 on page 213 RM1-1243-000CN ECU PCA, 220v Table 8-9 on page 219 RM1-1249-.
Part number Description Table and page RM1-1313-000CN Duplexer (HPLJ 1320) Table 8-6 on page 213 RM1-1313-000CN Duplexer (HPLJ 1320) Table 8-13 on page 227 RM1-1318-000CN Size-change assembly Table 8-.
Part number Description Table and page XB4-7401-005CN Screw, tapping, truss head m4x10 Table 8-6 on page 213 XB4-7401-005CN Screw, tapping, truss head m4x10 Table 8-7 on page 215 Table 8-15.
236 Chapter 8 Parts and diagrams ENWW.
Index A accessories, part numbers 201 accessory error secondary messages 161 acoustic specifications 9 Advanced Printer Settings, HP Toolbox 42 Alerts tab, HP Toolbox) 42 alignment, troubleshooting 14.
duplex path, clearing jams 180 duplex solenoid, removing 107 duplex-drive assembly, part numbers 220 duplex-drive gears, removing 104 duplex-drive PCA, removing 101 duplexer tray, removing 90 duplexer.
Java Virtual Machine 40 Jetdirect print servers, part numbers 201 K Korean EMI statement 18 L laser safety statement 18 laser statement for Finland 19 laser/scanner errors 158 operations 68, 74 removi.
parts ordering 200 removing and replacing 82, 83 phone numbers, ordering supplies 200 photosensitive drum inspecting 163 rotation functional checks 186 physical specifications 6, 22 pickup roller chan.
memory 7 physical 6 port availability 7 specks, toner 165, 170 speed specifications 6 spots, troubleshooting 165, 170 static precautions 82 status lights accessory error secondary messages 161 fatal e.
wavy pages, troubleshooting 148 Web sites, ordering parts 200 Windows HP Toolbox 40 software for 25 wire harnesses, replacing 82 wired network setup, troubleshooting 189 wireless communications card, .
.
Q5 92 7 - 90901 *Q5927-90901* *Q5927-90901* © 2004 C op yr ight He wlett-P ack ar d Dev elopment Com pan y , L.P . www .hp.com/su pport/lj1160 www .hp.
デバイスHP LaserJet 1320nwの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP LaserJet 1320nwをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP LaserJet 1320nwの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP LaserJet 1320nwの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP LaserJet 1320nwで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP LaserJet 1320nwを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP LaserJet 1320nwの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP LaserJet 1320nwに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP LaserJet 1320nwデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
