HPメーカーSlateBook x2の使用説明書/サービス説明書
ページ先へ移動 of 58
HP SlateBook 10 x2 PC Maintenance and Service Guide.
© Copyright 2013 Hewlett-Packard Development Company, L.P. Android is a U.S. registered trademark of Android Corporation. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. NVIDIA is a trademark of NVIDIA Corporation in the U.
Safety warning notice WARNING! To reduce the possibilit y of heat-re lated in juries or of overheating the device, do not place the device directly on your lap or obstruct t he device air vents.
iv Safety warning notice.
Table of contents 1 Product description ............. ............ ........... ................ ........... ........... ................ ........... ... ... 1 2 External component identification .......... .......... ............ .......... ..........
Volume button board ..... ......... ........... ......... ............ ......... ........... ......... ..... 28 TouchScr een cable .. ................ ................. ................... ................. ............ 29 Battery .... ............ ..
1 Product description Category Description Produc t Name HP SlateBook 10 x2 PC Proces sor NVIDIA® T40S 1.8-GHz pr ocessor (4-plus-1®, quad) Chipset NVIDIA Tegra 4, ARM® Cortex-A15 MPCore® Graphics 2D and 3D graphics Supports HD playback, streaming, and recording at 1080p and 30fps Panel 10.
Category Description Sensors Accelerometer eCompass Gyroscope Wireless Integrated wireless local area network (W LAN) options by way of wireless module One built-in WLAN antenna Supports Miracast Supports a Broadcom BCM4334 802.11abgn 1×1 Wi-Fi + BT 4.
Category Description Operating system Preinstalled: Android 4.2 Supports Android next version upgrade Serviceability End user replac eable parts: AC adapter 3.
2 External component identification Tablet Item Component Item Component (1) WLAN antenna (7) Speakers (2) (2) Internal microphone (8) Alignment openings (2) (3) Webcam light (9) Headphone/microphone .
Keyboard base Item Component Item Component (1) Caps lock key (6) HDMI port (2) Alignment posts (2) (7) Power conn ector (3) Mute key (8) Memory card reader (4) Tablet release latch (9) USB port (5) D.
3 Illustrated parts catalog Locating the serial number, product number, and model number The serial number and product number are located on the left edge of the tablet. You may n eed the information when you travel internat ionally or when you contact support.
Tablet major components Item Component Spare part number (1) Display panel (10.1-inch, AG, UWVA, WLED TouchScreen) 728152-001 (2) 2-cell, 25-Wh, 2.86-Ah, Li-io n battery (for use only in the tab let, .
Item Component Spare part number (6) Display panel cable (included in the Display Panel Cable Kit, spare part number 728 142-001) (7) System board equipped with an NVIDIA T40S 1.
Keyboard base major components Keyboard base major components 9.
Item Component Spare part number (1) HP TabletBook 10 x2 PC : The tablet is spared at the subcomponen t level only. For tablet subassembly spare part information, see Tablet major components on page 7 .
Item Component Spare part number (7) Docking board 728155-001 (8) Bottom cover (includes rubber foot): In royal blue finish 728140-001 In smoke silver finish 728138-001 In snow white finish 728139-001.
Sequential part number listing Spare part number Description 490371-001 Power cord for use in N orth America (3-pin, black, 1.83-m) 490371-011 Power cord for use in Aus tralia (3-pin, black, 1.83-m) 490371-021 Power cord for use in Europe (3-pin, black, 1.
Spare part number Description 728147-001 Hinge assembly in s moke silver finish (includes cables) 728148-001 Media card reader board (includes cable) 728149-001 TouchPad (includes cable) 728150-001 Power button board (includes cable) 728151-001 Volume button board (includes cable) 728152-001 10.
Spare part number Description 728160-AD1 Keyboard/top cover for use in South Korea 728160-B31 Keyboard/top cover for use in the Netherlands 728160-BG1 Keyboard/top cover for use in Switzerland 728160-.
4 Removal and replacement procedures preliminary requirements Tools required You will need the fo llowing tools to comple te the removal and replacement procedures: ● Flat-bladed screw driver ● Ma.
Cables and connectors CAUTION: When servicing the tablet, be sure that cables are placed in th eir proper locations duri ng the reassembly process. Improper cable placement can damage the tablet . Cables must be handled with extreme care to avoi d damage.
Typical electrostatic vo ltage levels Relative humidity Event 10% 40% 55% Motions of bench worker 6,000 V 800 V 400 V Removing DIPS from plastic tube 2,000 V 700 V 400 V Removing DIPS from vinyl tray .
Packaging and transp orting guidelines Follow these grounding guidelin es when packaging and transporting equipment : ● To avoid hand contact, transport produc ts in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and as se mblies with conductive or ap proved containers or packaging.
Equipment guidelines Grounding equipment must include eith er a wrist st rap or a foot strap at a grou nded workstation. ● When seated, wear a wrist strap co nnected to a gr ounded system. Wrist straps ar e flexible straps with a minimum of one megohm ±1 0% resistance in the ground co rds.
Removal and replacement procedures Tablet component replacement procedures CAUTION: Tablet components described in this chapter should only be accessed by an a uthorized service provider. A ccessing these pa rts can damage the ta blet and void the warra nty.
2. Remove the disp lay enclosure (2) from the table t. 3. Remove the display enclosure. Reverse this procedure to install the display enclosure. Rear webcam Description Spare part number Rear webcam (includes cable) 728159-001 Before removing the rear we bcam, follow these steps: 1.
Remove the re ar webcam : 1. Disconnect the battery cable from the system board. 2. Release the zero in sertion force (ZIF) connector (1) to which the rear webcam cable is att ached, and then disconnec t the rear webcam c able from the sys tem board. 3.
4. Remove the rear webcam (3) and cable . Reverse this procedure to install the rear webcam. Front webcam Description Spare part number Front webcam (includes microphone and cable) 728159-001 Before removing the front webcam, fo llow these steps: 1. Turn off the tablet.
3. Remove the Phillips PM2.0×2.0 scr ew (3) that secures the front webcam to the display assembly. 4. Remove the front webcam (4) and cable . Reverse this procedure to install the front we bcam. Display panel cable NOTE: The displa y panel cable i s included in the Disp lay Panel Cable Kit, s pare part number 728142-0 01.
3. Remove the display panel cable (3) . Reverse this procedure to install t he display pa nel cable. Wireless antenna Description Spare part number Antenna Kit (includes wireless antenna cable and t ransceiver) 728134-001 Before removing the wirel ess antenna, follow these steps: 1.
4. Detach the wireless antenna transcei vers (4) from the surfaces of the battery and the display panel frame. (The wireless antenna transceiver is attach ed to the surfaces of the batte ry and the display panel frame with double-sided tape.) 5. Remove the wireless antenna.
Remove the p ower button boar d: 1. Release the ZIF connecto r (1) to which the power button boar d cable is attached, and then disconnect the power button board cab le from the system board. 2. Detach the power button board cable (2 ) from the battery.
Volume button board Description Spare part number Volume button board (includes cabl e) 728151-001 Before removing the powe r button board, follow these s teps: 1. Turn off the tablet. If you are unsure whether the tabl e t is off or in Hibernation, turn the tablet o n, and then shut it down through the operatin g system.
TouchScreen cable NOTE: The TouchScreen ca ble is includ ed in the Displa y Panel Cable Kit, sp are part number 728142-0 01. Before removing the TouchScree n cable, follow these steps: 1. Turn off the tablet. If you are unsure whether the tabl e t is off or in Hibernation, turn the tablet o n, and then shut it down through the operatin g system.
Battery Description Spare part number 2-cell, 25-Wh, 2.86-Ah, Li-ion battery for us e only in the tablet (includes cable) 722232-005 Before removing the tablet batter y, follow these steps: 1.
3. Remove the battery (3) from the display as sembly. Reverse this procedure to install the tablet battery. Bezel Description Spare part number For use only in Asian Pacific (AP) countries and regions.
3. Disconnect all external devices from the tablet. 4. Remove the display enclo sure (see Display enclosure on page 20 ), and then remove the following compo nents: a. Rear webcam (see Rear webcam on page 21 ) b. Front webcam (see Front webcam on page 23 ) c.
Speakers Description Spare part number Speaker Kit (includes left and right speakers and cables) 728154-001 Before removing the speakers , follow these steps: 1. Turn off the tablet. If you are unsure whether the tabl e t is off or in Hibernation, turn the tablet o n, and then shut it down through the operatin g system.
5. Remove the speakers (5) . Reverse this proced ure to install t he speake rs. System board Description Spare part number Equipped with an NVIDIA T40S 1.8-GHz proces sor (4-plus-1, quad), 64-GB of memory, and a graphics subsystem with UMA memory (includes WLAN module and replacement thermal material) 728158-001 Equipped with an NVIDIA T40S 1.
c. Display panel cable (see Display panel cable on page 24 ) d. Wireless antenna (see Wireless antenna on page 25 ) e. Power button board (see Power button board on page 26 ) f. Vo lume button boar d (see Volume butto n board on page 28 ) g. TouchScreen cable (see TouchScree n cable on page 29 ) h.
Keyboard base component replacement procedures CAUTION: Keyboard b ase components described in th is chap ter should only be accessed by an authorized servic e provider. Acce ssing thes e parts ca n damage the keyboard base and void the warranty. This chapter provides removal and replacement proced ures for authorized service provider only parts.
3. Remove the bottom cover (4) . Reverse this procedure to install the bottom cover. Battery Description Spare part number 2-cell, 21-Wh, 3.38-Ah, Li-ion battery for use on ly in the keyboard base (includes cable) 7222 31-005 Before removing the keyboard base batter y, follow these steps: 1.
Remove the keyboard base battery: 1. Disconnect the battery cable (1) from the k eyboard baseing board. 2. Remove the eight Phillips PM2.0× 2.5 screws (2) that secure the battery to the keyboard/ top cove r. 3. Remove the keyboard base battery (3) . Reverse this procedure to inst all the keyboard ba se battery.
Remove the m edia card reader bo ard: 1. Release the ZIF connecto r (1) to which the media card reader bo ard cable is attached, and the n disconnect the media card reader board cable from the docking board. 2. Detach the media card reader boar d cable (2) from the keyboard/top cover.
Before removing the hin ge assembly, follow th ese steps: 1. Turn off the tablet and keyb oard base. If you are unsure whether th e tablet and keyboard base are off or in Hi bernation, turn the tablet on, and then shu t it down through the opera ting system.
Docking board Description Spare part number Docking board 728155-001 Before removing the docki ng board, follow these steps: 1. Turn off the tablet and keyb oard base. If you are unsure whether th e tablet and keyboard base are off or in Hi bernation, turn the tablet on, and then shu t it down through the opera ting system.
3. Remove the docking board (2) . Reverse this proc edure to install the docking bo ard. 42 Chapter 4 Remova l and replacemen t procedures p reliminary requ irements.
TouchPad Description Spare part number TouchPad (includes cable) 728149-001 Before removing the TouchPad, follow these step s: 1. Turn off the tablet and keyb oard base. If you are unsure whether th e tablet and keyboard base are off or in Hi bernation, turn the tablet on, and then shu t it down through the opera ting system.
5 Specifications Metric U.S. Tablet dimensions Width 25.8 cm 10.2 in Depth 18.2 cm 7.2 in Height 0.9 cm 0.4 in Weight 0.6 kg 1.3 lbs Keyboard base dimensions Width 25.8 cm 10.2 in Depth 19.4 cm 7.6 in Height 1.0 cm 0.4 in Weight 0.6 kg 1.3 lbs Comput er dime nsions (tablet and keyboard base) Width 25.
Metric U.S. Nonoperating -15 m to 12,192 m -50 ft to 40,000 ft NOTE: Applicable product safety standards spec ify thermal limits for plastic surfaces .
6 Backing up and recovering your data Updating apps, widgets, and the operating system HP recommends that you update your app s, widgets, and the operating system on a regu lar basis to the latest versions. Updates can re solve issues an d b ring new features and options to your tablet.
Factory data reset To reset all settings and dele te all data on the device: 1. To access Settings, touch t he All apps icon, and then touch Settings . 2. Under PERSONAL , touch Back up & re set . 3. Under PERSONAL DATA , selec t Factory data reset , and then follow the on-screen instructions.
7 Power cord set requirements The wide-range input fe ature of the computer permit s it to oper ate from any l ine voltage from 100 to 120 volts AC, or from 220 to 240 volts AC. The 3-conductor power cord set in cluded with the computer meets t he requirements for use in the country or region where the equipment is purchased.
Country/region Accredited agency Applicable note number France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 The Netherlands KEMA 1 Norway NEMKO 1 The People's Republic of China COC 5 South Korea EK 4 Sweden CE MKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1.
8 Recycling When a non-rechargeable or rech argeable battery has reached the end of its useful life, do not dispose of the battery in general household waste.
Index A AC adapter, sp are part number 11, 12 action keys 5 alignment opening 4 alignment post 5 antenna location 4 removal 25 spare part number 7, 12, 25 Antenna Kit, spare pa rt number 7, 12, 25 aud.
memory card reader 4, 5 memory, product description 1 micro-US B-to-USB cable, spare part number 11, 12 microphone location 4 product desc ription 1 microphone jack 4, 5 model name 1 mute key 5 O oper.
デバイスHP SlateBook x2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
HP SlateBook x2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP SlateBook x2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP SlateBook x2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP SlateBook x2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP SlateBook x2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP SlateBook x2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP SlateBook x2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP SlateBook x2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。