HumminbirdメーカーPlatinum ID 120の使用説明書/サービス説明書
ページ先へ移動 of 36
.
TABLE OF CONTENTS INSTALLATION PREPARATION………………………………………………………. 2 Parts Supplied……………………………………………………………………. 2 Accessories……………………………………………………………………….
INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fishsinder, please ensure the following p arts are included in the box: • Fishfinder • Transducer with .
INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminbird fishfinder includes a standard transducer. This transducer can be mounted on the transom of the boat or bonded to the inside of a fi berglass hull boat.
INSTALLATION PREPARATION ALTERNATE MOUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything necessary for installation and operation on most boats. However, there are several situations which may require a different type of transducer.
INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replac ements for the standard transducer. You may exchange your new and unassembled transducer for another type by returning it to the address listed in Customer Support.
INSTALLATION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This chapter contains information critical to the correct installation of your transducer. Due to the wide variety of boat hulls, only general instructions are presented in the installation guide.
INSTALLATION TRANSOM INSTALLATION • If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence, and a different mounting technique or transducer type should be considered. S tep Two - Drill the Mounting Holes 1.
INSTALLATION TRANSOM INSTALLATION Step Four - Mount the Transducer to the Transom 1. Apply silicone sealant to the mount ing holes drilled into the transom.
INSTALLATION TRANSOM INSTALLATION Step Six - Route the Cable There are several ways to route the transducer cable to the to the area where the control head will be installed. The most common procedure routes the cable through the transom into th e boat.
INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be instal led and operational. See Installing the Control Head for instruction on installing the unit. Inside the hull mounting generally produces good results in single thickness fiberglass - hulled boats.
INSTALLATION INSIDE THE HULL INSTALLATION 3. Power up the Control Head. 4. Run the boat at variou s speeds and water depths while observing the screen on the Control Head. If the unit functions well at low speeds but begins to skip or miss the bottom at higher speeds, the transducer needs to be moved.
INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One - Determine Where to Mount Begin the installation b y determining where to mount the control head.
INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse (not included) for the protection of the unit (Figure 21). Humminbird is not responsible for over voltage or over current failures. In order t o minimize the potential for interference with other marine electronics a separate power source (such as a second battery) may be necessary.
INSTALLATION CONTROL HEAD INSTALLATION Step Five - Assembling the Connector Holder 1. Insert the cable connectors into the connector holder. The cable connectors are labeled, and there are corresponding labels on the connector holder (Fi gure 26).
INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm basic operation with the boat trailered. Press POWER once to turn the unit on. There will be an audible chirp when any button is pressed to confirm the button press.
THANK YOU THANK YOU Thank you for choosing Humminbird, America’s #1 name in depth sounde rs. Humminbird has built its reputation by manufacturing top quality, thoroughly reliable marine equipment.
USING THE PLATINUM ID 120 HOW SONAR WORKS HOW SONAR WORKS There are two main components to a Platinu m ID installation: the sensor, which you will install on the transom or inside the hull, and the Platinum ID unit. The sensor and Platinum ID communicate by means of a cable, and are powered by your boat’s 12 - volt DC battery.
USING THE PLATINUM ID 120 HOW SONAR WORKS The P latinum ID uses the returned signals to display a detailed underwater image, and constantly updates the display as you travel across the water. The display informs you of the current depth and reveals individual fish, schools of fish, their location, botto m details as well as bottom hardness.
USING THE PLATINUM ID 120 PLATINUM ID FEATURES POWER: Press the button once to turn the Platinum ID on, then press again to turn the unit off. When the unit is off, keeping POWER pressed for about two seconds starts the built - in simulator.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS OPERATING THE PLATINUM ID This section provides complete information on operating the Platinum ID through its front panel controls.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS PLATINUM ID FUNCTIONS The Platinum ID offers several functions that you can adjust with the front panel buttons. (Note that to select something with a button, you must press it fully so that you can hear a “chirp” sound.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS The three position bottom hardness scale at the bottom of the screen helps differentiate between grass or muddy (soft) bottoms and structure or rock (hard) bottoms. After you adjust any function, the display returns to its full - screen reading.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS 1. Selecting ID Factory Setting: F ish Symbols ID identifies targets not attached to the bottom and displays them with either a fish symbol or an arch. Three different size fish symbols are used to represent the returned signal strength, a good indicator of fish size.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS 3. Selecting Sensitivity Factory Setting: + 0 The Platinum ID automatically adjusts to the proper amount of sensitivity for conditions (ie depth). You can bias the setting + or – 5 levels to suit your personal taste.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS 5. Enabling Fish Alarm Factory Setting: OFF The Fish Alarm alerts you with a chirping sound whenever the Platinum ID detects fish (or another object not attached to the bottom). To activate it, select FISH ALARM and press the ON - OFF button.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS 7. Using Bottom - Lock Factory Setting: OFF Bottom - Lock provides an up - close view like Zoom Ran ge, except that in this case the zoomed view automatically moves up or down to stay on the bottom. To use this feature, select BOTTOM LOCK and press ON - OFF.
USING THE PLATINUM ID 120 OPERATING INSTRUCTIONS 9. Setting Depth R ange Factory Setting: ON (Automatic) When you turn the Platinum ID on, it finds the bottom, sets the ideal Depth Range, and automatically adjusts the Depth Range (to as much as 120’) as the depth changes.
SPECIFICATIONS Operating Frequency 455KHz Power Requirement 10 - 16 volts DC Power Cable L ength 48” Sensor (standard) SHS6 - 16 Sensor Cone Angle 16 degrees Depth Range 0 - 15’, 0 - 30’, 0 - 60.
MAINTENANCE AND WARRANTY MAINTENANCE MAINTENANCE Your Humminbird fishfinder is designed to provide years of trouble free operation with virtually no maintenance. Follow these simple procedures to ensure your Humminbir d continues to deliver top performance.
MAINTENANCE AND WARRANTY TROUBLESHOOTING TROUBLESHOOTING Do not attempt to repair the fishfinder yourself. There are no user serviceable parts inside, and special tools and techniques are required for reassembly to ensure the waterproof integrity of the housing.
MAINTENANCE AND WARRANTY TROUBLESHOOTING Second, inspect the transducer cable from end to end for breaks, kinks, or cuts in the outer casing of the cable. Also ensur e the transducer is fully submerged in water. If the transducer is connected to the unit through a switch, temporarily connect it directly to the unit and try again.
MAINTENANCE AND WARRANTY TROUBLESHOOTING 5. The unit comes on before I press POWER, and won't turn off. Check the transducer cable. If the outer jacket of the cable has been cut and the cable is in contact with bare metal, you need to repair the cut with electrical tape.
MAINTENANCE AND WARRANTY WARRANTY HUMMINBIRD ONE YEAR FULL WARRANTY First year repairs (from original date of purchase) on your Humminbird fishfinder are absolutely free.
MAINTENANCE AND WARRANTY SERVICE POLICY SERVICE POLICY This S ervice Policy is valid in the United States only. This applies to Humminbird units returned to our factory in Eufaula, Alabama, and is subject to change without notice. All repair work is performed by factory - trained technicians to meet exacting factory s pecifications.
MAINTENANCE AND WAR RANTY CUSTOMER SUPPORT CUSTOMER SUPPORT If you have any questions, call our Humminbird Customer Support Hotline: 1 - 334 - 687 - 0503 Throughout the U.
デバイスHumminbird Platinum ID 120の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Humminbird Platinum ID 120をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHumminbird Platinum ID 120の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Humminbird Platinum ID 120の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Humminbird Platinum ID 120で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Humminbird Platinum ID 120を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHumminbird Platinum ID 120の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Humminbird Platinum ID 120に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHumminbird Platinum ID 120デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
