Hunterメーカー41545の使用説明書/サービス説明書
ページ先へ移動 of 25
1 41545-01 6/10/2002 ® Installation and Operation Manual For Hunter Ceiling Fans 41545-01 6/10/2002.
2 41545-01 6/10/2002 ®.
3 41545-01 6/10/2002 ® CONGRA TULA TIONS! Y our new Hunter ceiling fan is an addition to your home or office that will provide comfort and perfor - mance for many years. This manual gives you complete instructions for installing and operating your fan.
4 41545-01 6/10/2002 ® CONTENTS CONGRA TULA TIONS! ............................................................................................................... .......................... 3 IMPORT ANT INFORMA TION ..................................
5 41545-01 6/10/2002 ® IMPOR T ANT INFORMA TION not lock the circuit br eakers in the off position, secur ely fasten a prominent warning device, such as a tag, to the service panel. • All wiring must be in accor - dance with national and lo- cal electrical codes and ANSI/NFP A 70.
6 41545-01 6/10/2002 ® GA THERING THE TOOLS Y ou will need the following tools for installing the fan: • Electric drill with 9/64" bit • Standard screwdriver • Phillips-head scr ewdriver • W rench or pliers OPTIONAL ACCESSORIES Consider using Hunter’ s optional ac- cessories, including a wall-mounted or remote speed contr ol.
7 41545-01 6/10/2002 ® INST ALLER’S CHOICE ® This patented 3-position mounting system provides you maximum instal- lation flexibility and ease. Y ou can install your Hunter fan in one of three ways. The steps in this manual in- clude specific instructions for the fan mounting method of your choice.
8 41545-01 6/10/2002 ® STEP 2 - INST ALLING THE CEILING PLA TE 4. Align the slotted holes in the ceil- ing plate with the pilot holes in the wood support structur e. Note: The isolation pads should be flush against the ceiling. 1. Drill two pilot holes into the wood support structure thr ough the outermost holes on the outlet box.
9 41545-01 6/10/2002 ® Figure 2c - Attaching Ceiling Plate to 2 x 4 Brace 2 x 4 Brace Ceiling Joist Ceiling Outlet Box Ceiling Plate Flat Washer 3" W ood Screw 5. Place a flat washer on each of the two 3" scr ews and pass the screws through the slotted holes in the ceiling plate as shown in Figure 2c.
10 41545-01 6/10/2002 ® Some fans are shipped with the decorative upper and lower housings detached from the fan motor . This step tells you how to attach the hous- ing. If the housing for your fan is al- ready attached to the fan motor , go directly to STEP 4 - ASSEMBLING THE F AN.
11 41545-01 6/10/2002 ® continued STEP 4 - ASSEMBLING THE F AN Use the Step 4 instructions for the type of mounting you have selected: standar d, angle, or flush. ST ANDARD AND ANGLE MOUNTING For Standard 8-foot Ceilings and Higher 1 . Insert the pipe through the canopy as shown in Figure 4a.
12 41545-01 6/10/2002 ® Figure 4d - Attaching Canopy to Fan Assembly Assembly Washer Adapter Threaded Hole Figure 4c - Positioning Assembly W asher Slots over Threaded Holes 3. Position the slots in the assem- bly washer over the threaded holes in the adapter as shown in Figur e 4c.
13 41545-01 6/10/2002 ® STEP 5 - WIRING THE F AN 1. Disconnect the power by turning off the cir cuit breakers to the out- let box and associated wall switch location. 2. Tilt and hang the assembled fan from the ceiling plate hooks. Slip two rectangular canopy slots over ceiling plate hooks as shown in Figures 5a and 5b.
14 41545-01 6/10/2002 ® Bare or Green Green Approved Connectors Power Wires In Ceiling White White Black Black/White 1 2 Connections: Black Wall Switch Wire For Separate Control of Light Fixture Ceil.
15 41545-01 6/10/2002 ® STEP 6 - HANGING THE F AN Figure 6a - Attaching Canopy to Ceiling Plate Figure 6b - Canopy T abs and Gr ooves in Hanger Ball Sub-steps 1 and 2 apply to Flush, Standard, and Angle mounting. Sub- step 3 applies to Standar d and Angle mounting only .
16 41545-01 6/10/2002 ® Figure 7a - Inserting Gr ommet into Fan Blade Figure 7b - Attaching Fan Blade to Blade Iron Figure 7c - Attaching Fan Blade to Blade Iron using Decorative Medallion feature a decorative medallion as well as a blade ir on.
17 41545-01 6/10/2002 ® 4. For each blade, insert one blade mounting screw thr ough the blade iron as shown in Figure 7d, and attach lightly to the fan.
18 41545-01 6/10/2002 ® STEP 8 - ATT ACHING THE SWITCH HOUSING Figur e 8a - Attaching Upper Switch Housing to Switch Housing Mounting Plate Housing Assembly Screw Switch Housing Mounting Plate Upper .
19 41545-01 6/10/2002 ® 5. Connect the upper plug connec- tor from the motor to the lower plug connector in the lower switch housing assembly . See Fig- ure 8c. Note: Both plug connectors are polarized and will only fit together one way . Make sure that both connectors are pr operly aligned before connecting them together .
20 41545-01 6/10/2002 ® STEP 9 - INST ALLING LIGHT FIXTURE INST ALLING ACCESSORY LIGHT KITS T o install the light kit, follow the in- structions included with the kit for wiring, mounting, and assembly .
21 41545-01 6/10/2002 ® dir ect breeze. In winter , having the fan draw air upward (clock- wise blade rotation) will distrib- ute the warmer air trapped at the ceiling around the r oom without causing a draft. OPERA TING YOUR HUNTER F AN 1. T urn on electrical power to the fan.
22 41545-01 6/10/2002 ® Save Energy and Money While Protecting the Environment Congratulations! Y ou're saving energy and money while protecting the environ- ment by purchasing this ENERGY ST AR qualified Hunter ceiling fan! With this Hunter fans have the power to cut your cooling costs up to 40%.
23 41545-01 6/10/2002 ® CLEANING AND MAINTENANCE Caring for blades: Wood finish blades should be cleaned with a fur - niture polishing cloth. Occasionally , a light coat of furniture polish may be applied for added protection and beauty . Painted and high-gloss blades may be cleaned in the same manner as the fan finish.
24 41545-01 6/10/2002 ® TROUBLESHOOTING Nothing happens; fan does not move. Noisy operation. 1. Power turned off, fuse blown, or circuit br eaker tripped. 2. Loose wire connections or wrong connections. 3. Motor reversing switch not en- gaged. 4. Pull chain switch not “on.
25 41545-01 6/10/2002 ® PROBLEM PROBABLE CAUSE SOLUTION Noisy operation (continued). Excessive wobbling. Note: When switching from medium to low speed, you may notice some fan wobble. When the fan stabilizes at low speed, wobble will disappear . 4. Using non-approved speed control.
デバイスHunter 41545の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter 41545をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter 41545の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter 41545の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter 41545で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter 41545を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter 41545の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter 41545に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter 41545デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
