Hunter FanメーカーMB517-01の使用説明書/サービス説明書
ページ先へ移動 of 21
MB517-01 • 03/10/15 • © Hunter F an Company www .HunterF anInternational.com ENGLISH.
Befor e installation and usage of this produc t, please read this manual and keep it for future ref erence ..
www .HunterF anInternational.com PA G E 10 PA G E 5 PA G E 19 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy T .
www .HunterF anInternational.com MB517-01 • 03/10/15 • © Hunter F an Company What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician.
www .HunterF anInternational.com T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools .
4 MB517-01 • 03/10/15 • © Hunter F an Company www .HunterF anInternational.com If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (included) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) .
www .HunterF anInternational.com C eiling Bracket OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak.
www .HunterF anInternational.com C eiling Bracket (c ontinued) Prepar ation D I S C A R D D I S C A R D Remove the shipping blocks fr om the motor . Discard the screws. Note: Some fans will hav e a shipping ring instead of shipping blocks. Please remove the ring and discar d the screws.
7 MB517-01 • 03/10/15 • © Hunter F an Company www .HunterF anInternational.com Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Option 1 Option 2 skip to next page If you need a diff erent downrod leng.
8 MB517-01 • 03/10/15 • © Hunter F an Company www .HunterF anInternational.com KEEP! Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. Downrod (c ontinued) Tighten the setscrew with pliers.
www .HunterF anInternational.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball int o the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canopy sit loosely on t op of the fan.
10 MB517-01 • 03/10/15 • © Hunter F an Company www .HunterF anInternational.com Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x.
www .HunterF anInternational.com Wiring (c ontinued) T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x.
www .HunterF anInternational.com Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts int o the hanging bracket as shown. Insert the two canopy screws found in the hardware bag .
www .HunterF anInternational.com Put the blade washers , found in the hardware bag , onto the blade screws, f ound in the hardwar e bag. Then install the blade screws to secure each blade to a blade ir on.
www .HunterF anInternational.com Make sure the upper switch housing is securely attached to the mounting plate. F ailure to properly secure all 3 assembly screws could result in the switch housing xture falling.
15 MB517-01 • 03/10/15 • © Hunter F an Company www .HunterF anInternational.com Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. F ailure to properly secure all three assembly screws could result in the light xture falling.
www .HunterF anInternational.com Light Kit (c ontinued) Note: In complianc e with US federal energy regulations , this ceiling fan contains a device that restricts its light output. Exceeding the wattage limit marked on the MAX wattage sticker afx ed to the light socket(s) may result in re hazard or improper operation.
www .HunterF anInternational.com Rocker- Style Plate Switch Co ver Plate Removed T abs T o install the transmitter cradle , remove the two screws holding the switch cov er plate. Do not remove the c over plate. Orient the cradle b y lining up the two mounting holes with those on the cov er plate.
www .HunterF anInternational.com F or cleaning the fan, use soft brushes or cloths to prevent scr atching. Cleaning products may damage the nishes. Reverse Switch Opera tion, Maintenance , & Cleaning (continued) T o switch the direction of air ow , move the reverse switch t o the opposite position.
www .HunterF anInternational.com T roubleshooting Exc essive w obbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , suppor t the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc tions to balance the fan.
デバイスHunter Fan MB517-01の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter Fan MB517-01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter Fan MB517-01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter Fan MB517-01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter Fan MB517-01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter Fan MB517-01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter Fan MB517-01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter Fan MB517-01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter Fan MB517-01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
