Husqvarnaメーカー115 24 05-95の使用説明書/サービス説明書
ページ先へ移動 of 18
W ARNING The engine exhaust fr om this product contains chemicals known to the State of Calif ornia to cause cancer , birth defects or other repr oductive W ARNING Before using our pr oducts, please read this manual carefully to under stand the proper use of y our unit.
English 2 Y OUR WARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), CARB (California Air Resources Board), Envir onment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2007 and later small nonroad engine.
English 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Notes on types of warnings . . . . . . .
English 4 SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken into consideration to prevent possible serious bodily injury , and for this reason you ar e requested to read all such instructions carefully and follow them without fail.
English 5 For safe operation and maintenance, symbols are carved in relief on the machine. Using to these indications, please be careful not to make a mistake.
English 6 WORKING CONDITIONS 1. Refrain from operating the blower if you are tir ed, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. T o reduce the risk of hearing loss associated with sound levels, hearing protection is requir ed.
English 7 BEFORE ST ARTING THE ENGINE Each time before starting the engine, inspect the entire unit to see if every par t is in good order and is securely tightened in place. If any damage is found in the fuel line, the exhaust line, or the ignition wiring, do not use the blower until it has been repair ed.
English 8 MAINTENANCE 1. In order to maintain your product in pr oper working order , per form the maintenance and checking operations described in the manual at regular intervals. 2. Always be sure to turn off the engine and disconnect the spark plug before performing any maintenance or checking procedur es.
English 9 1 . Frame 2. Harness 3. Spark Plug Cap 4. Throttle Lever 5. Net 6. Choke Lever 7. Air Cleaner 8. V olute Case, Cover 9. “CAUTION” Label 10. Elbow 11. Fuel T ank 12. Recoil Starter 13. Stop Switch with Throttle Position Setting 14. Engine Cover 15.
English 10 - The data shown above are those in the case of one straight pipe. - Specifications are subject to change without notice. MODEL 150BT Dimensions (L x W x H) mm (in) 351x446x479 (13.8x17.6x18) Dry Weight kg (lbs) (including pipe) 10.2 (22.5) Dry Weight kg (lbs) (without accessories) 9.
English 11 SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the har dware supplied with the unit. NOTE A light lubricant may be used to ease assembl y of flexible hose to blower elbo w .
English 12 Tighten the side straps so that the pressure is evenly distributed acr oss the shoulders. WAIST BEL T - The waist belt is attached to the rings on the left and right sides of the frame. Place the waist belt around your waist and not too far down on the stomach.
English 13 FUEL W ARNING - Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground f or fueling and move at least 10ft (3m) away fr om the fueling point before starting the engine .
English 14 ST ARTING ENGINE IMPORT ANT - A void operating the b lower with the flexible tube and s wivel joint disconnected. That will reduce the cooling air and the engine could be damaged by o verheating. 1. Push the primer bulb until fuel flows out in the clear tube.
English 15 ADJUSTING IDLE SPEED - The idling speed is set for 2200 rpm at the factory . If it is necessary to adjust the idle speed, use the adjustment screw on the top side of the carburetor . (1)Idling Adjustment Screw ST OPPING ENGINE - Move the throttle lever to the STOP position.
English 16 Maintenance, replacement, or r epair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. W ARNING Make sure that the engine has stopped and is cool before perf orming any service to the blower .
English 17 SP ARK PL UG - The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. The spark gap should be adjusted to .
English 18 IGNITION COIL AIR GAP INSPECTION - If the gap is not accurate or when installing the coil or rotor , adjust the air gap between the ignition coil and the iron cor e of the rotor . Air Gap: 0.40 mm (0.35 to 0.45 mm) / 0.016 in (0.014 to 0.
デバイスHusqvarna 115 24 05-95の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 115 24 05-95をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 115 24 05-95の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 115 24 05-95の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 115 24 05-95で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 115 24 05-95を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 115 24 05-95の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 115 24 05-95に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 115 24 05-95デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
