IBMメーカー4690の使用説明書/サービス説明書
ページ先へ移動 of 40
IB M 469 0 S to re S y s t e m: T R -4 T a p e Dri v e U s e r’ s G ui d e Las t Up da ted: F ebrua ry 1 9 , 1 9 98 IBM.
.
IB M 469 0 S to re S ys te m: T R -4 T a p e Dri v e U s e r’ s G ui d e Las t Up da ted: F ebrua ry 1 9 , 1 9 98 IBM.
© Copyright International Business Machines Corporation 1998. All rights reserved. Note to U.S. Government Users — Documentation related to r estricted rights — Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.
Contents Notices .............. v T rademarks .............. v Preface ..............v i i Who Should Read This Manual ....... v i i How This Manual is Organized ....... v i i Related Publications ........... v i i Store System Related Publications — Software vii Store System Related Publications — Hardware ix General Publications .
iv TR-4 T ape Drive User ’s Guide.
Notices References in this publication to IBM pr oducts, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any refer ence to an IBM product, program, or service is not intended to state or imply that only IBM’s product, pr ogram, or service may be used.
vi TR-4 T ape Drive User ’s Guide.
Preface This book describes the 4690 Store System support for both the SCSI and the EIDE tape drives. Who Should Read This Manual This book is intended for users who are familiar with har dware and so.
IBM 4690 Store System: 4690 T erminal Services for DOS User’ s Guide , SC30-3688 IBM 4680 and 4680-90 General Sales Application IBM 4680-90 General Sales Application: Planning and Installation Guide.
In-Store Pr ocessing: IBM OS/400 – Application Development Guide , SC30-3535 In-Store Pr ocessing: IBM 4680 OS – Application Development Guide , SC30-3536 Store System Related Publications — Har.
Scanners IBM 1520 Hand-Held Scanner User ’ s Guide , GA27-3685 IBM 4686 Retail Point-of-Sale Scanner: Physical Planning, Installation, and Operation Guide , SA27-3854 IBM 4686 Retail Point-of-Sale S.
IBM 4680 Support for COBOL V ersion 2 (Softcopy provided with the pr oduct) IBM 4680 Store System Regr ession T ester (Softcopy provided with the pr oduct) IBM 4680 X.
xii TR-4 T ape Drive User ’s Guide.
Chapter 1. Overview The operating system provides support for the following tape drives: v EIDE Internal v SCSI Internal v SCSI External Refer to the IBM 4690 OS V2: User’s Guide for more information on using the Streaming T ape Drive Utility . The following table shows the tape drives supported.
Compatibility with the Floppy Drive Because the tape drive attaches to either a SCSI or IDE cable instead of the floppy ribbon cable and does not use DMA channel 2, there is no contention with the floppy drive. Installation Flexibility The tape drives install in either a 5.
Chapter 2. T ape Drive Installation This chapter contains hardwar e and software installation instructions for the TR-4 tape drives. It contains instructions for both the EIDE tape drive and the SCSI internal and external tape drives. Attention: Before installing this pr oduct, see “Safety” on page 25.
SL – Slave CS – Cable Select Each of the two IDE cables (primary and secondary) normally has two connectors for attaching two IDE devices (master and slave). The C: drive must be on the primary IDE cable, and the tape drive must be on the secondary IDE cable.
Master on primary IDE: C: drive Slave on primary IDE: none Master on secondary IDE: D: drive Slave on secondary IDE: tape drive In the configuration above, you do not need to change the jumper on the tape drive, but you may need to change the jumper on the D: drive.
Step 3. Mounting the Drive 1. Locate an available bay or space in your store contr oller to mount the tape drive. The tape drive can be mounted in either a horizontal or vertical position.
each item in the list, press the Enter key and use the arr ow keys to move between items. Press the Enter key to select the item. Pr ess the Esc key to return to the pr evious screen. Also, make sure that the tape drive is r eported as “Installed”.
Step 3. Configuring the SCSI Drive 1. Locate the SCSI configuration block. The SCSI configuration block pin assignments are: 15 and 16 Enable terminator power 13 and 14 Enable termination 1 1 and 12 Reserved 9 and 10 Reserved 7 and 8 Enable parity 5 and 6 SCSI bit 2 3 and 4 SCSI bit 1 1 and 2 SCSI bit 0 2.
Note: Y ou can also mount the drive in a 5.25-inch (1.6-inch high) bay using the 5.25-inch mounting kit provided. When you attach the brackets to the sides of the 3.5-inch tape drive, you increase the width and height of the drive. The installation instructions ar e located on the mounting kit packaging.
Step 1. Planning Y our SCSI Configuration Plan what SCSI ID to give the tape drive connected to the SCSI bus adapter . Each device on the adapter bus must have a unique ID. Y ou cannot assign a device 7 because most SCSI bus adapters use this as their ID.
3. Locate the SCSI ID push switch on the back of the tape drive. Select the SCSI ID for the drive by pressing the + or − button until the desir ed ID (0 through 7) appears in the window . Step 4. Completing the Installation 1. Check your SCSI bus cable connections.
Enabling the Feature After purchasing the featur e, you should run the featurization diskette to tell the operating system that you have purchased it. T o enable the feature: 1. W ith the operating system running, start a Command Mode session. 2. Insert the 4690 Featurization Diskette.
Chapter 3. Using the T ape Drive This section provides information on using the tape drive featur es. It explains the procedur es for loading and unloading tape cartridges and setting the write-protect switch.
Checking the Reliability of the T ape Data After the Streaming T ape Drive Utility completes a list or restor e operation, the message “Reliability: T ape drive recovered fr om xxx soft errors” appears, with xxx repr esenting the number of 512-byte blocks that could not be read successfully on the first attempt.
E025 – Logical unit not ready , manual intervention requir ed. E026 – Logical unit not ready , format in progr ess. E027 – Logical unit not ready , operation in progr ess. E028 – Logical unit does not respond to selection. E029 – Multiple peripheral devices selected.
E1 17 – Medium magazine locked. E1 18 – Invalid bits in identify message. E1 19 – Logical unit has not self-configured yet. E120 – T arget operating conditions have changed. E121 – Microcode has been changed. E122 – Changed operating definition.
E035, E054, E055, E056, E057, E124, E126, E127, E128, E129, E130, E134, E139, E142, E143, E158, E176 – These errors normally indicate a tape drive hardwar e problem.
18 TR-4 T ape Drive User ’s Guide.
Chapter 4. T ape Drive Specifications TR-4 1/4-inch tape cartridge technology of fers fast, ef f icient, high capacity storage in a compact, easy-to-remove har d-shell package. This mass-storage technology evolved from the original r eel-to-reel 1/2-inch tape storage medium.
Drive-Performance Specifications The following table lists the performance specifications for the tape drive . Drive Performance Feature Specification Capacity 4.
Environmental Requirements Specification Operational Nonoperational V ibration Peak to peak displacement Peak acceleration 0.005 in. max (5 to 44.3 Hz) 0.50 g max (44.3 to 500 Hz) 0.1 in. max (5 to 17 Hz) 1.5 g max (17 to 500 Hz) Acoustic level operational (a-wt sum) 55 dBA maximum (measured in suitable enclosure at 3-ft.
22 TR-4 T ape Drive User ’s Guide.
Chapter 5. Maintenance and T roubleshooting This chapter describes several maintenance and troubleshooting pr ocedures for the TR-4 EIDE Internal T ape Drive and the TR-4 SCSI T ape Drives.
T roubleshooting EIDE T ape Drive If the Store Contr oller is indicating an error during the boot process prior to the “IBM 4690 OS 386 V1 ...” message, the problem is not in the 4690 softwar e. The problem is either a har dware failure, a har dware configuration problem, downlevel BIOS, or downlevel firmware in the tape drive.
v The device has a hardwar e problem. The “Reliability: T ape drive recovered fr om xxx soft errors” message displayed by the Streaming T ape Drive Utility is a normal message unless the number indicated by xxx is high. The number can exceed several hundred if the tape is full (contains 4 GB of data).
IBMR Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber ..
デバイスIBM 4690の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IBM 4690をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM 4690の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM 4690の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM 4690で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM 4690を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM 4690の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM 4690に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM 4690デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
