IBMメーカーPSB Form Factor Board SAGP-845EVの使用説明書/サービス説明書
ページ先へ移動 of 48
SAGP-845EV User Manual Version 2.0 SOCKET 478 PENTIUM 4/4-M with 10/100 Ethernet LAN & AGP4X VGA SBC March 1, 2004 ©Copyright 2004 by ICP Electroni cs Inc.
2 Copyright Notice The information in t his document is subjected to ch ange without prior not ice in order to improve reliability , design and funct ion and does not represent a commitment on the part of the manufacturer .
3 Table of Contents Chapter 1 Introduction ....................................................... 4 1.1 Specifications .................................................................................... 4 1.2 Package Co ntents ......................
4 Chapter 1 Introduction SAGP-845EV is a PSB form factor boar d to work with a high performance processor . It is equipped with advanc ed multi-mode I/O, and designed for system manufacturers, integrators, or V ARs who want to provide reliable and quality performance at a reasonable price.
5 Bi-directional parallel port Configurabl e to LPT1, LPT2, LPT3 or disabled Supports EPP/ECP/SPP Hardware monitor Monitors power su pply voltage and fan speed status IrDA port Supports Serial Infrared (SIR) and Amplitude Shift K eyed IR (ASKIR) interface USB port Supports 4 USB2.
6 1.2 Package Contents • SAGP-845EV single board computer x 1 • FDD cable x 1 • A T A/100 IDE cable x 1 • A TX-12V cable x 1 • PS/2 Y splitter cables for keyb oard and mouse connecti on x 1 .
7 Chapter 2 Installation This chapter describes how to install the SAGP-845EV . At first, the la yout of SAGP-845EV is shown, and the unpacking in formation that you should be careful with is described.
8 2.2 Clear CMOS Setup If the user wants to clear the CMOS Setup data (for example, the user forgot the password and needed to clear the setup data then set the password again), the user should close the JP2 (set the jumper to 2-3) about 3 seconds, then open it again.
9 Chapter 3 Connection This chapter describes how to connect peri pher als, switches an d indicators to the SAGP-845EV board. Table of Connectors Label Function FDD1 Floppy Disk Drive Connector IDE1 P.
10 3.1 Floppy Disk Drive Connector SAGP-845EV board has a 34-pin co nnector for the floppy drive. • FDD1: FDC Connector PIN Description PIN Description 1 GROUND 2 REDUCE WRITE 3 GROUND 4 N/C 5 GROUN.
11 3.2 Ultra ATA33/66/100 IDE Disk Drive Connector Each of the SAGP-845EV IDE connectors can ha ve one IDE (Integrated Device Electronics) attached to it.
12 3.3 Parallel Port This port is usually connected to a prin ter . SAGP-845EV includes an on-board parallel port accessed through a 26-pin flat -cable.
13 3.4 Serial Ports SAGP-845EV offers two high speed NS16C550 compatible UAR T s with Read/R eceive 16-byte FIFO serial ports. • COM1 10-pin Connector PIN Description 1 DA T A CARRIER DETECT (DCD) 2.
14 3.5 Keyboard Connector SAGP-845EV provides a 6-pin k eyboard/mouse connector . • KBM1: 6-pin Mini-DIN Keyboard/Mouse Connector PIN Description 1 KEYBOARD DA T A 2 MOUSE DA T A 3 GROUND 4 +5V 5 KEYBOARD CLOCK 6 MOUSE CLOCK 3.6 USB Port Connector SAGP-845EV provides 4 built -in USB2.
15 3.8 Fan Connector SAGP-845EV provides three CPU coo ling fan connectors, which supply 12V/500mA. • FAN1/FAN2/FAN3: CPU Fan Connector PIN Description 3 Sensor 2 12V 1 Ground 3.9 LAN RJ45 Connector SAGP-845EV is equipped with a built -in 10/ 100Mbps Ethernet controller .
16 3.11 Audio Connectors SAGP-845EV has an onboard audio contro ller (CMEDIA CMI8738LX) that connects input and output devices through pin-headers (CN4). The audio controll er supports 5.1 channel sounds includin g LINEOUT , REAR, and CENTER/BASS. CD-IN (CDIN1).
17 3.12 Compact Flash Storage Card Socket SAGP-845EV configures Compact Flash Stor age Card to IDE mode. This type II Socket is compatible with IBM Micro Drive.
18 3.13 External Switches and Indicators There are several external switches and indicators f or monitoring and controllin g your CPU board. All the f unctions are integrated in CN2 connect or .
19 Chapter 4 Award BIOS Setup 4.1 Introduction This chapter discusses the setu p program in the BIOS. It will give users a step- by-step guidance to configure the system. The user -defined configuration is then stored in the battery-back ed CMOS RAM, which retains the customized information wh ile the power is off .
20 4.3 Using Setup In general, the arrow k eys are used to hi ghlight items, and then press <Enter> to select the item. Th e following table provides more deta ils about how to navigate in the setup program using the k eyboard.
21 4.4.1 Setup Items The main menu inclu des the following main setup categories. Recall that some systems may not include all entries. Standard CMOS Features Use this menu for basic system configurat ion. See Section 4.5 for the details. Advanced BIOS Features Use this menu to set the advanced features available on the system.
22 4.5 Standard CMOS Setup The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes none, one or more than one setup items. Use the arrow k eys to highlight the item and then use the <PgUp> or <PgDn> k eys to select the wanted va lue for each item.
23 Main Menu Selections Item Options Description Date MM DD YYYY Set the system date. Time HH : MM : SS Set the system time IDE Primary Master Options are in its sub menu (Described in T able 2) Press.
24 IDE Adapters The IDE adapters control the hard disk drive. Use a separate sub menu to configure each hard disk drive. Figure 2 shows the IDE primary master sub menu.
25 4.6 Advanced BIOS Features This section allows us ers to configure the system for basic operation. The options for the system’ s default speed, boot-up se quence, keyboard oper ation, shadowing and security are available.
26 Virus Warning Allows users to choose the VIRUS W arning feature for IDE Hard Di sk boot sector protection. If this function is enabl ed and someone attempts to write data into this area, BIOS will show a warn ing message on screen and alarm beep will be heard.
27 Boot Up NumLock Status Select power on state for NumLock. The choice: On/Off . Gate A20 Option Select if chipset or keyboard controller should control GateA20. Normal A pin in the keyboard controller controls GateA20 F ast Lets chipset control GateA20 Typematic Rate Setting K ey strokes repeat at a r ate determined by the k eyboard controller .
28 Report No FDD For Win 95 Whether report no FDD for Win 95 or not. The choice: Y es, No. Small Logo (EPA) Show Disabled/Enabled Small Logo (EPA) Show .
29 4.7 Advanced Chipset Features CMOS Setup Utility – Copyright © 1984 – 2000 Award Software Advanced Chipset F eatures DRAM Timing Selectable By SPD CAS Latency Time 1.
30 DRAM RAS# to CAS# Delay • This field lets users insert a timing delay between the CAS and RAS strobe signals. • It is used when DRAM is writte n to, read from, or refreshed. • Choice 2 means shorter delay which sh ortens the process of charging; and choice 3 means longer delay which lengthens the process of charging.
31 On-chip VGA Enabled/Disabled On-chip VGA Flash BIOS Disabled/Enabled Flash BIOS 4.8 Integrated Peripherals CMOS Setup Utility – Copyright © 1984 – 2000 Award Software Integrated P eripher als .
32 IDE Primary/Secondary Master/Slave UDMA Ultra DMA -33/66 implementation is possible on ly if the IDE h ard drive supports it and the operating en vironment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver).
33 Watchdog Timer Unit Select the W atchdog Ti mer unit. The choice: Second, Minute. 4.9 Power Management Setup The Power Management Setup al lows the user to configure the system to the most effective energy save.
34 Power Management This category allows th e user to select the type (or degree) of power saving related to the following modes: 1. HDD Power Down 2. Doze Mode 3. Suspend Mode There are four selections for Power Mana gement, three of which have fix ed mode settings.
35 HDD Power Down When enabled and after th e set time of system inactivity , th e hard disk drive will be powered down while all oth er devices remain active. The choice: 1Min, 2Min, 3M in, 4Min, 5Min , 6Min, 7Min , 8Min, 9Min, 10Min, 11Min, 12Min, 13Min, 14Min, 15Min, Disabled.
36 4.10 PnP/PCI Configuration Setup This section describes configurin g the PC I bus system. PCI stands for Personal Computer Interconnect. It is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components.
37 IRQ3/4/5/7/9/10/11/12/14/15 assigned to This item allows th e user to determine t h e IRQ assigned to the ISA bus and is not avai lable to any PCI slot.
38 4.12 Frequency/Voltage Control CMOS Setup Utility – Copyright © 1984-2000 Award Software Frequency/V oltage Control CPU Clock Ra tio 8 X Auto Detect PCI Clk Enabled Spread Spectrum Disabled CPU .
39 4.13 Defaults Menu Selecting “Default s” from the main menu will bring up the t wo options described below . Load Fail-Safe Defaults If the user presses <Enter> on this item , a dialog bo.
40 4.14 Supervisor/User Password Setting The user can set the password for either su pervisor or user , or for both of them. Supervisor password: for entering and changing the settings of the system U.
41 4.15 Exit Selecting Save & Exit Setup Pressing <Enter> on this item asks for confirmati on: Save to CMOS and EXIT (Y/N)? Y Pressing “Y” stores the selections made in the menus in CMOS – a special sect ion of memory that stays on after the syst em has been turned off .
42 Appendix A Watchdog Timer The W atchdog Timer is provided to ensu re that standalone systems can always recover from catastrophic conditions that cause the CPU to cr ash.
43.
44 Appendix B Address Mapping IO Address Map I/O address Range Description 000-01F DMA Controller 020-021 Interrupt Controller 040-05F System time 060-06F K eyboard Controller 070-07F System CMOS/Real.
45 1st MB Memory Address Map Memory address Description 00000-9FFFF System memory A0000-BFFFF VGA buffer F0000-FFFFF System BIOS 1000000- Extend BIOS IRQ Mapping Table IRQ0 System Timer IRQ8 R TC clock IRQ1 K eyboard IRQ9 USB2.
46 Appendix C How to Upgrade a New BIOS Note: Before flashing BIOS, please enable th e item “FLASH BIOS” in BIOS setting. The user can install an upgrade BIOS for the SAGP-845EV download from the manufacturer’s web si te (http://www .ieiworld.com ).
47 new BIOS file WITHOUT a warni ng prompt. A simple file name for savi ng the old BIOS to is OLDBIOS.BIN. 9. Y ou r second option, in sequ ence, will be wheth er you want to flash your BIOS. Enter Y (for "yes"). Note: This is the critical step .
48 Appendix D AGP Slot This IPC CPU Card has an Acceler ated Gr aphics P ort (AGP) slot that supports +1.5V AGP card. When you buy an AGP card, make sure that yo u ask for one with +1.5V specification. Note the notche s on the card golden fingers to ensure that they fit the AGP slot on your ICP CPU card.
デバイスIBM PSB Form Factor Board SAGP-845EVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IBM PSB Form Factor Board SAGP-845EVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM PSB Form Factor Board SAGP-845EVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM PSB Form Factor Board SAGP-845EVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM PSB Form Factor Board SAGP-845EVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM PSB Form Factor Board SAGP-845EVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM PSB Form Factor Board SAGP-845EVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM PSB Form Factor Board SAGP-845EVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM PSB Form Factor Board SAGP-845EVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
