IBMメーカーThinkCentre 9212の使用説明書/サービス説明書
ページ先へ移動 of 42
ThinkC e n tr e ™ Hard w are Rep l a c ement Gu i d e Ty p e s 92 1 2 92 1 3 .
.
ThinkC e n tr e ™ Hard w are Rep l ac ement Gu i d e Ty p e s 92 1 2 92 1 3 .
Second Edition (March 2005) © Copyright International Business Machines Corporation 2005. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure r estricted by GSA ADP Schedule Contract with IBM Corp.
Contents Overview . . . . . . . . . . . . . .v Safety information for replacing CRUs . . . . . .v Safety information for replacing FRUs . . . . . .v Additional information resour ces . . . . . . .v T ools requir ed . . . . . . . . . . . . .v i Handling static-sensitive devices .
iv Hardwar e Replacement Guide.
Overview This guide is intended to be used by customers who are r eplacing Customer Replaceable Units (CRUs) as well as trained service personnel who are r eplacing Field Replaceable Units (FRUs). In this guide, CRUs and FRUs will often be referr ed to as parts.
To access this information, point your browser to http://www .ibm.com/pc/support/. T ools required To replace some parts in your computer , you might need a flat-blade or Phillips screwdriver .
Chapter 1. Locations This chapter provides illustrations to help locate the various connectors, contr ols and components of the computer . To remove the cover , see “Removing the cover” on page 5. Locating components The following illustration will help you locate the various components in your computer .
Locating connectors on the front of the computer This section shows the various external connectors on the computer to which you can attach external devices.
Locating connectors on the rear of the computer The following illustration shows the location of connectors on the rear of the computer . 1 Power supply diagnostic LEDs 11 USB connectors (.
Identifying parts on the system board The system board (sometimes called the planar or motherboard ) is the main cir cuit board in your computer . It provides basic computer functions and supports a variety of devices. The following illustration shows the locations of parts on the system board.
Chapter 2. Replacing hardware Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
To replace the cover , go to “Completing the parts replacement” on page 31. Removing and replacing the front bezel 1. Remove the computer cover . See “Removing the cover” on page 5. 2. To release the front bezel fr om the chassis, press the blue button at the top of the chassis and pull the bezel outward as shown.
3. Push the blue release lever 1 to the left and pull the blue handle 2 outward. Pivot the har d disk drive outward to the fully open position as shown. 4. Disconnect the power supply cables 1 and 2 connected to the system board.
5. Remove the four screws at the rear of the chassis that secur e the power supply . 6. Press inward on the metal r etainer inside the chassis and remove the power supply from the computer . 7. Install the new power supply into the chassis so that the screw holes in the power supply align with those in the chassis.
11 . Push the blue lever 1 and pivot the hard disk drive inward until it is latched into position. 12. Go to “Completing the parts replacement” on page 31.
Replacing the system board assembly Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
7. Remove the screws 1 through 7 . 8. Slide the system board toward the fr ont of the computer to disengage it from the mounting tabs and lift it out. 9. Place the defective system board next to the new system board on a clean, flat surface.
12. Install the new system board assembly into the computer chassis by aligning the four slots in the metal plate on the bottom of the system board with the tabs in the chassis. Important Make sure to corr ectly align the metal plate on the bottom of the system board with the tabs in the chassis.
Replacing the microprocessor Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
5. Pivot lever 1 securing the heat sink until it is fully in the up position. Remove the heat sink 2 from the system boar d by carefully lifting it up and off the system boar d. Note: If you are r eplacing a defective system board you must r einstall the same heat sink.
7. Using the vacuum pen 1 , remove the micropr ocessor from the system boar d socket by lifting it straight up and out of the socket. Important Do not touch the gold contacts on the bottom of the micropr ocessor . If you must touch the micropr ocessor , touch only the sides.
9. Loosen the protective cover 3 that protects the gold contacts on the micropr ocessor 2 but do not remove it. Use the vacuum pen 1 to pick up the micropr ocessor then completely remove the cover .
11 . Using the vacuum pen 1 , lower the microprocessor straight down into the micropr ocessor socket. Note: Install the black protective cover that was r emoved from the new micropr ocessor onto the defective micropr ocessor after the installation is complete.
13. Slide the heat sink 2 into position over the microprocessor . Lower the lever 1 to secure the heat sink. Note: If you are r eplacing a defective system board, use the heat sink that was removed earlier . 14. If you are replacing the system boar d, continue at step 12 on page 12.
Replacing a memory module Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
Replacing a PCI adapter Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
5. Pivot the blue adapter latch to the closed position to secure the adapters. 6. Go to “Completing the parts replacement” on page 31. Chapter 2. Replacing hardwar e 21.
Replacing a hard disk drive Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
4. Slide the hard disk drive out of the hard drive bay by pulling the blue handle. 5. Remove the defective hard disk drive from the blue bracket by flexing the bracket. 6. To install the new hard disk drive into the blue bracket, flex the bracket and align the pins 1 through 4 on the bracket with the holes in the har d disk drive.
7. Insert the new hard disk drive into the hard drive bay with the cir cuit board side facing downward. 8. Connect the power and signal cables to the new hard disk drive. See “Identifying parts on the system board” on page 4. 9. Press the blue tab 1 to pivot the drive into the computer .
Replacing an optical drive Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
5. Install the optical drive into the bay until it snaps into position. 6. Connect the signal and power cables to the drive. 7. Go to “Completing the parts replacement” on page 31.
Replacing the diskette drive Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
Replacing the keyboard Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
Replacing the mouse Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
Replacing the internal speaker Attention: Do not open your computer or attempt any repair befor e reading the “Important safety information” in the Quick Reference that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer .
Completing the parts replacement After replacing a failed part, you need to install any other r emoved parts, install the computer cover , and reconnect any cables, including telephone lines and power cords. Also, depending on the part that was r eplaced, you might need to confirm the updated information in the Setup Utility program.
4. Reconnect the external cables. Plug the power cord into the computer then into a properly gr ounded power receptacle. See “Locating connectors on the fr ont of the computer” on page 2 and “Locating connectors on the rear of the computer” on page 3.
.
Part Number: 39J7726 Printed in USA (1P) P/N: 39J7726.
デバイスIBM ThinkCentre 9212の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IBM ThinkCentre 9212をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM ThinkCentre 9212の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM ThinkCentre 9212の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM ThinkCentre 9212で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM ThinkCentre 9212を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM ThinkCentre 9212の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM ThinkCentre 9212に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM ThinkCentre 9212デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
