ImpexメーカーMWB-9000の使用説明書/サービス説明書
ページ先へ移動 of 29
NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruc tion Parts L ist Warranty Ordering Parts Model MWB-9000 Retain This Manual for Reference 06-21-05 OWNER'S MANUAL MARCY SMITH MACHINE MWB-9000 IMPEX INC.
TA BLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 SMITH MACHINE HARDW ARE PACK….
IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assembl e or operate y our machine.
SMITH MA CHINE HA RDEWA RE PA CK 3.
SMITH MA CHINE HA RDEWA RE PA CK 4.
SMITH MA CHINE HA RDEWA RE PA CK 5.
SMITH MA CHINE A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and A llen Wrenches. NOTE: It is strongly recommended tw o or more people assembling this machine to av oid possible injury . STEP 1 (See Diagram 1) A.
STEP 2 (See Diagram 2) A.) Attach a Fr ont Vertical Frame (#6) to the R ight Base Frame ( #2). Secure it w ith two M 10 x 2 ¾” Carri age Bolts ( #77), Ø ¾” W ashers (#87), and M10 Ai rcraft Nuts (#88). Do not tig hten the Nuts and Bolts yet. B.
DIAGRAM2 8.
STEP 3 (See Diagram 3) A.) Attach the R ear Vertic al Frame (#14) to the Rear Base Frame ( #5). Secure it with tw o M10 x 2 ½ ” Allen Bol ts (#69), four Ø ¾” W ashers (#87), and two M10 Ai rcraft Nuts (#88). Sli de the Sliding W eight Post (#13) onto the Rear Ver tical Frame (#14).
STEP 4 (See Diagram 4) A.) Attach the Left & Rig ht Lat Bar Frames (#16 & #17) to the Upper Fr ame (#10). Ali gn the holes and secure each Lat Bar Fr ame to Upper Frame w ith one M10 x 5” Al len Bolt (#67) , two Ø ¾ ” W ashers (#87), and one M10 Airc raft Nut (#88).
STEP 5 (See Diagram 5) A.) Attach the Butter fly Base (#23) to the front of Middle Vertic al Frame (#4) . Attach the Butterfly Pull ey Bracket ( #24) to the back of the Frame. Secure them w ith tw o M10 x 2 ¾” Car riag e Bolts (#77), Ø ¾ ” W ashers (#87), and M10 Airc raft Nuts (#88).
CABLE LOOP DIAGRAM 12.
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Inser t the 242” Upper Cable (#35) through the sw ivel pulley bracket pre-installed i n the top front of the Right Lat Bar Frame ( #17). B.) Instal l a Ball Stopper (#86) onto the end of the Cable.
DIAGRAM 6 14.
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of the 76” Butter fly Cabl e (#36) to the cli p on the Left Butterfly (#26). Draw the Cable to the Butterfly Base Bracket (#24) .
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach one end of the 140” H igh- Low Cabl e (#38) to the br acket on the Sliding W eight Post (#13). Secure i t wi th one M10 x 1 3/8” Allen Bolt ( #72), two Ø ¾” W ashers (#87), and one M10 Aircr a f t Nut (#88).
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 68” Lower Cable ( #37) to the opening on the bottom of Middle Verti cal Frame (#4). Attach a Pul ley to the openi ng. Secure i t wi th one M10 x 2 ½ ” Allen Bol t (#69), tw o Long Pulley Bushing s (#48), and one M10 Aircr aft Nut (#88).
18.
SMI TH M ACHINE PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Left Bas e Fram e 1 51 2” x 1 ¾” Sleeve 2 2 Right Base Fram e 1 52 1” End Cap 2 3 Cross Brace 1 53 Ø 1” Con-s haped End Cap 8 4 Middle.
MULTI-PURPOSE BENCH HA RDWA RE PA CK 20.
MULTI-PURPOSE BENCH A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and A llen Wrenches. NOTE: It is strongly recommended this machine be assembled by tw o or more people to avoid possible inj ury. STEP 1 (See Diagram 1) A.
STEP 2 (See Diagram 2) A.) Attach four Bushi ngs (#21) to a Seat Support Frame (#6) . B.) Attach a Backr est Support (#7) to the rear of the Seat Support Frame (#6) . Alig n the holes and secure them w ith one M10 x 1 ¾” Al len Bolt (#31) and ∅ ¾” W asher (#36).
STEP 3 (See Diagram 3) A.) Pl ace the Backrest Board (#12) onto the Backrest Supports (#7) . Secure it with four M 8 x 2” Al len Bolts ( #34) and ∅ 5/8” W ashers (#37). B.) Pl ace the Seat Pad (#11) onto the Seat Support Fr ames (#6). Secure it wi th four M8 x 2” Allen Bolts ( #34) and Ø 5/8” W ashers (#37).
STEP 4 (See Diagram 4) A.) Attach the Leg Dev eloper (#5) to the open bracket on the Mai n Frame (#1). Secur e it w ith an Axle ( #14), tw o M10 x ¾” All en Bolts (#30), and tw o ∅ ¾” W ashers (#36). B.) Insert one Foam Tube (#10) hal fway through the hol e on the Main Frame.
STEP 5 (See Diagram 5) A.) Attach the Ar m Curl Pad ( #13) to the Arm C url Stand (#4) . Secure it w ith two M8 x 5/8” Allen Bolts ( #35) and tw o ∅ 5/8” W ashers (#37). Insert the Arm Cur l Stand into the front opening on the M ain Frame (#1) .
26.
MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Arm Curl Stand 1 5 Leg Devel oper 1 6 Seat Support Frame 2 7 Backrest Support 2 8 Sl.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be f ree fr om defects in workm ans hip and m aterial, under norm al us e and ser vice c onditions , f or a period of two years on the Fram e f rom the date of pur chas e.
デバイスImpex MWB-9000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Impex MWB-9000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはImpex MWB-9000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Impex MWB-9000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Impex MWB-9000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Impex MWB-9000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はImpex MWB-9000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Impex MWB-9000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちImpex MWB-9000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
