Ingersoll-Randメーカー8506-Aの使用説明書/サービス説明書
ページ先へ移動 of 18
OPERATOR’S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION MANUAL Released: M30 33 3-l-77 Tool Products Revised: l-27-95 “O” SERIES “QRT” SCREWDRIVERS Models: 8506-A( ), 8509-A( ), 8515-A( ) and 8521-A( ). 1018-2 READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. I I Wear hearing protection when operating this tool. Turn off air supply and disconnect air supply hose before installing, . removing or adjusting any accessory on this tool, or before performing any maintenance on this tool.
ROUTINE LUBRICATION REQUIREMENTS M30 33 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.
MODEL IDENTIFICATION MODELS WITH -EU SUFFIX ARE “EC” COMPLIANT MODELS. NOTE: GENERAL PURPOSE WRENCH 37167 FURNISHED WITH -A AND -T MODELS. DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air before performing maintenance or service to tool.
DRIVE SECTION M30 ADJUSTABLE CLUTCH 33 CLUTCH ADJUSTMENT Remove clutch assembly (36310) from tool. Place pin in hole of jaw (36318) or wrench on square end of spindle (36311) to adjust nut (36313). To adjust properly, release nut to least tension. Tight- en nut one or two positions -each click = one position.
DRIVE SECTION TORQMATIC CLUTCH CLUTCH ADJUSTMENT Remove clutch assembly from tool. Place wrench on square end clutch. Clutch assembly should contain approximately 1/8 oz. (3.5 of spindle (38322) to adjust nut (38313). To adjust properly, re- g) of grease.
.
GEARING SECTION DRIVE GEARING DISASSEMBLY a. b. Remove spindle and components from ring gear. To remove gears from spindle, remove bearing, spacer and shafts. ASSEMBLY NOTE: Pack bearings and lubricate gears liberally with ARO 33153 grease upon assembly.
GEARING SECTION M30 AUXILIARY GEARING 33 DISASSEMBLY a. Grasp adapter (ring gear) in one hand and tap splined end of spindle with a soft face hammer; spindle and components will 33153 grease upon assembly. Gearing should contain approxi- loosen from adapter.
MOTOR SECTION DISASSEMBLY a. Remove motor from housing. Grasp cylinder in one hand and tap splined end of rotor with a soft face hammer; motor will assemble over rotor, aligning air inlet holes of cylinder with air come apart. inlet slots of end plate.
HEAD SECTION M30 33 DISASSEMBLY a. Remove roll pin (Y178-25), releasing trigger (45469). b. Remove screw (Y222-156-C) releasing shroud (45468). c. Grasp end of valve assembly (47880) and pull to remove valve assembly and bushing (45465). d. Remove retaining ring (Y147-68), releasing screens (42911) and muffler (45474).
QTY 1 1 5 6 1 1 1 2 1 PART NUMBER 31092 31093 31363 36317 41795 41799 41954 42911 45474 SERVICE KIT NO. 42114 FOR SERVICING ADJUSTABLE CLUTCH MODELS DESCRIPTION SPRING THRUST PIN BLADE PIN MOTOR OIL G.
ACCESSORIES 44361-( ) PIPED EXHAUST SYSTEM ASSEMBLY M30 33 30302-( ) INLET HOSE - 5/16” I.D. 1/4” P.T.F. THREAD P.T.F. THREAD TO AIR SUPPLY 46672-l ADAPTER ASSEMBLY 2622 HOSE ADAPTER 3/8” MALE N.P.T.F. 1/2” I.D. 43551-6 MUFFLER 3/8” FEMALE N.
ACCESSORIES HOUSING AND ADAPTER ASSEMBLIES FlNDER ADAPTER IS PRESSED INTO HOUSING. FINDER ADAPTER 39332 HOUSING ASSEMBLY HOUSlNG AND FINDER ADAPTER -USE WITH FlNDERS 36106-(), 36105-(), 41292-() AND 41292-(). ALSO USE WITH GUIDES 30334-(), 40261 AND 41767.
ACCESSORIES FINDERS EXTENSION FINDER FOR 1/4” HEX BITS M30 33 NOTE: SPRING 30111 AND LOCK SPRING 31574 REQUIRED FOR USE WITH FINDERS (ORDER SEPARATELY). USE WITH FINDER ADAPTER 36332. BELL MOUTH FINDER FOR 1/4” HEX BITS Similar to standard finders except that each finder will accept mm sizes and types of screw heads.
ACCESSORIES BITS AND BIT HOLDERS 1/4” HEX DRIVE BITS EXTENSION BLADED BITS FOR SLOTTED SCREWS. PART NO. LENGTH POINT SIZE SHAFT DIA. 30320-l 1-15/16” 1 .182” 30320-2 1-15/16” 2 .246” PHILLIPS BITS 30320-3 1-15/16” 3 .310” 31531-1 2-3/4” 1 .
SOCKET HEAD DRIVERS MAGNETIC BIT HOLDER USE WITH GUIDE BUSHING 46261. SQUARE DRIVE ADAPTERS USE WITH GUIDE BUSHING 30334-( ). ACCESSORIES M30 BITS AND BIT HOLDERS 33 HEX BALL LOCK ADAPTER PART NO. LENGTH HEX SETSCREW CAP SCREW SHAFT DIA. SIZE SIZE SIZE 30370-2 3/32” #10-#12 #4-#5 .
PN 49999-032.
デバイスIngersoll-Rand 8506-Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ingersoll-Rand 8506-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIngersoll-Rand 8506-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ingersoll-Rand 8506-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ingersoll-Rand 8506-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ingersoll-Rand 8506-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIngersoll-Rand 8506-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ingersoll-Rand 8506-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIngersoll-Rand 8506-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
