INSTEONメーカーSWITCHLINC 2476Dの使用説明書/サービス説明書
ページ先へ移動 of 35
INSTEON SwitchLinc V2 ™ ™ INSTEON Dimmer Switch For models: #2476D SwitchLinc V2 Dimmer.
INSTEON SwitchLinc V2 Dimmer User’s Guide TABLE OF CONTENTS ABOUT INSTEON SW ITCHLINC DIMMER ................................................................................................. 4 What is INSTEON? .......................................
ABOUT INSTEON ............................................................................................................................... ....... 29 Understanding Why an INSTEON Network Is Relia bl e ...............................................
INSTEON SwitchLinc V2 Dimmer User’s Guide ABOUT INSTEON SWITCHLINC DIMMER Congra tulations on purchasi ng the INSTEO N ™ SwitchLinc ™ Dimmer. With its elegant look, smooth touch, and stylish LED.
INSTEON SwitchLinc V2 Dimmer User’s Guide HOW TO INSTALL SWITCHLINC DIMMER ools You Will Need ove the faceplate from the switch junction box. junction box. remove them. Caution Read and understand these instructions before instal ling, and retain them for future reference.
INSTEON SwitchLinc V2 Dimmer User’s Guide Preparing to Install SwitchLinc Dimmer IMPORTANT! If you are not knowledgeable about and comfortable with electrical circuitry, you should have a qualified electrician install SwitchLinc Dimmer for you.
INSTEON SwitchLinc V2 Dimmer User’s Guide Installing SwitchLinc Dimmer 1. For best INSTEON Network performance, be sure y ou have properly installed at least two SignaLinc RF Signal Enhancers. 2. At the circuit breaker or fuse panel, di sconnect the power for all of the circuits in the switch junction box.
INSTEON SwitchLinc V2 Dimmer User’s Guide Installing SwitchLinc Dimme r in a Multi-Way Circuit Understanding Multi-Way Circuits If more than one switch controls a single set of lights (called a LOAD), the switches are part of a multi-wa y circuit.
INSTEON SwitchLinc V2 Dimmer User’s Guide Using SwitchLinc Dimmers in Virtual Multi-Way Circuits In a virtual multi-way circuit, only one SwitchLinc Dimmer, calle d the SwitchLinc Primary , actually controls the LOAD in the multi-way circuit.
INSTEON SwitchLinc V2 Dimmer User’s Guide Step-by-Step Instructions for Inst alling Multi-Way SwitchLinc Dimmers When replacing a three-way mechanical switch, each switch will have thr ee wires connected to it from the wall box. Four-way or greater circui ts will have four wires connected to the switches in the center of the circuit.
INSTEON SwitchLinc V2 Dimmer User’s Guide 3. Cap the other TRAVELER w ire. The other TRAVELER wire, usually red, will not be used, so put a wire nut on the end of it. 4. Cap the red LOAD wire from the SwitchLinc Secondary. Put a wire nut on the en d of the SwitchLinc Secondary’ s LOAD wire to ensure that it won’t connect to anything.
INSTEON SwitchLinc V2 Dimmer User’s Guide 6. Connect the S w itchLinc Secondary ’s GROUND Wire. Connect the bare copp er GROUND wire to the other GROUND wires in the junction box.
INSTEON SwitchLinc V2 Dimmer User’s Guide 10. Cap the other TRAVELER w ire. The other TRAVELER wire, usually red, will not be used, so put a wire nut on the end of it. 11. Connect the S w itchLinc Primary’s LOAD Wire. U s e a wire nut to con nect the LOAD wire, usually red, to the SwitchLinc Primary’s red LOAD wire.
INSTEON SwitchLinc V2 Dimmer User’s Guide HOW TO SET UP SWITCHLINC DI MMER TO REMOTE LY CONTROL AN INSTEON DEVICE Linking SwitchLinc Dimmer to a Controlled INSTEON Device To use SwitchLinc Dimmer a s an INSTEON Controll er, follow these steps to link Switch Linc Dimmer and a controlled INSTEON Device together.
INSTEON SwitchLinc V2 Dimmer User’s Guide Unlinking a Controlled INSTEON Device from SwitchLinc Dimmer If you are no longer going to use a n INSTEON Device that has previously been linked to SwitchL.
INSTEON SwitchLinc V2 Dimmer User’s Guide HOW TO SET UP SWITCHLINC DIMMER TO BE REMOTELY CONTROLLED BY AN IN STEON CONTROLLER Linking an INSTEON Controller to SwitchLinc Dimmer To remotely control SwitchLinc Dimmer using anot her INSTEON Controller, follow these steps to lin k SwitchLinc Dimmer an d the INSTEON Controller toget her.
INSTEON SwitchLinc V2 Dimmer User’s Guide Unlinking SwitchLinc Dimmer fr om an INSTEON Controller If you are no longer going to control a SwitchLin c Di mmer with an INSTEON Controller, it is very i.
INSTEON SwitchLinc V2 Dimmer User’s Guide HOW TO SET UP ON-LEV ELS AND RAMP RATES Setting the On-Level and Ramp Rates (Optional) The On-Level is the brightness that the light you are controlling will go to when you turn it on. The On- Level is adjustable from OFF to 100% brightness.
INSTEON SwitchLinc V2 Dimmer User’s Guide Setting the Ramp Rate The Ramp Rate sets the time it will take for the li ght you are controlling to go from OFF to t he On-Level brightness, or from the On-Level bri ghtness to OFF. This time is adjusta ble from 0.
INSTEON SwitchLinc V2 Dimmer User’s Guide ADVANCED FEATURES OF SWITCHLINC DIMMER Restoring Power to SwitchLinc Dimmer SwitchLinc Dimmer stores all of its settings in non-vo latile memory, so they ar e not lost even when power is removed.
INSTEON SwitchLinc V2 Dimmer User’s Guide X10 PROGRAMMING OPTIONS SwitchLinc Dimmer i s X10 ready, meaning that it c an respond to X 10 commands from an X10 Controlle r and it can send X10 commands to X10 devices. However, to operate SwitchLinc Dimmer in X10 mode , you must first set up an X10 Primary Address .
INSTEON SwitchLinc V2 Dimmer User’s Guide Setting the X10 On-Level and X10 Ramp Rate for the X10 Primary Address When an X10 Controller sends an X10 ON or X10 OFF command to SwitchLinc Dimmer’s Primary X10 Address, the Local On-Level and Local Ramp Rate apply.
INSTEON SwitchLinc V2 Dimmer User’s Guide ADVANCED X10 PROGRAMMING OPTIONS You can remotely set up X10 Scen e Addresses as well as On-L evels and Ramp Rates using an X10 Controller capable of sen ding an X 10 address (house code and unit code) without sending X10 O N or OFF commands.
INSTEON SwitchLinc V2 Dimmer User’s Guide 4. Send the following X10 Address sequen ce to lock in the ne w Ramp Rate: 5. SwitchLinc Di mmer will flash the light it is wired to and blink an LED in its LED Bar, indicating that the Ramp Rate has been set for the X10 Primary Address.
INSTEON SwitchLinc V2 Dimmer User’s Guide 3. Send an X10 ON or OFF command. 4. Send the following X10 Address sequen ce: 5. Send the X10 Scene Address (house code and unit code) that is to be removed. 6. SwitchLinc Di mmer will flash the light it is wired to and blink an LED in its LED Bar, indicating that the X10 Scene Address has b een removed.
INSTEON SwitchLinc V2 Dimmer User’s Guide HOW TO USE SWITCHLINC DIMMER Using the Paddle The Paddle Top makes your light go ON and the Paddle Bottom makes you r light go OFF. • Tap the Paddle Top to make your light go at the Local Ramp Rate from whatever brightness it currently has to the Local On-Level bri ghtness.
INSTEON SwitchLinc V2 Dimmer User’s Guide COLOR OPTIONS FOR SWITCHLINC DIMMER Paddle and LED Colors are Changeable You can change the color of SwitchLi nc Dimmer’s LEDs and al so its paddle and trim frame to match th e décor of any room.
INSTEON SwitchLinc V2 Dimmer User’s Guide Insert the new light pipes with the protrusions facing the center 5. Orient the new small light pipe with its protrusion facing toward the center of the frame and snap it into place. If placed in backwards or reversed, it will not click into place.
INSTEON SwitchLinc V2 Dimmer User’s Guide ABOUT INSTEON Understanding Why an INSTEON Network Is Reliable INSTEON messages travel throughout the home via Powerline Carrier (PLC) signals on the existing house wiring, and also via wirel ess Radio Frequ ency (RF).
INSTEON SwitchLinc V2 Dimmer User’s Guide About INSTEON and X10 Possible BoosterLinc Interference with INSTEON If you have installed older Smarthome Plug-In BoosterLinc™ X10 Signal B oosters or certain other BoosterLinc-enabled product s, the older BoosterL inc technology may interfere with INSTEON communications.
INSTEON SwitchLinc V2 Dimmer User’s Guide TROUBLESHOOTING Problem Possible Cause Solution Make sure the circuit breaker is turned on. Make sure the air gap (SET Button) is not pulled out. Check junction box wires to ensure all connections are tight and no bare wires are expose d.
INSTEON SwitchLinc V2 Dimmer User’s Guide Problem Possible Cause Solution Remove the X10 Primary Address or X10 S cene Address from SwitchLinc Dimmer.
INSTEON SwitchLinc V2 Dimmer User’s Guide SPECIFICATIONS SwitchLinc Dimmer Specifications General Smarthome Product Number 2476D2, INSTEON SwitchLinc V2 Dimmer Switch Warranty 2 years Operation On-Levels 32 Ramp Rates (full-ON to full-OFF) 0.125 to 9 seconds if programmed locally, 0.
INSTEON SwitchLinc V2 Dimmer User’s Guide Mechanical Paddle Type True rocker action Paddle and Trim Frame Color White installed, Ivory included; Optional Almond, Black, Brown, or Gray with #2400xx kits Wire Nuts 5 included Mounting Mounts in single or multiple-ganged junction box.
INSTEON SwitchLinc V2 Dimmer User’s Guide Certification SwitchLinc V2 Dimmer has bee n thoroughly tested by ITS ETL SEMKO, a nationally recognized independent thi rd-party testing labo ratory. The North American ET L Listed mark signifies that the product has be en tested to and has met the requirements of a widely recognized consen sus of U.
デバイスINSTEON SWITCHLINC 2476Dの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
INSTEON SWITCHLINC 2476Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはINSTEON SWITCHLINC 2476Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。INSTEON SWITCHLINC 2476Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。INSTEON SWITCHLINC 2476Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
INSTEON SWITCHLINC 2476Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はINSTEON SWITCHLINC 2476Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、INSTEON SWITCHLINC 2476Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちINSTEON SWITCHLINC 2476Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
