iRobotメーカー530の使用説明書/サービス説明書
ページ先へ移動 of 16
Mirra global.ir obot.com Pool Cleaning Robot Model 530 Owner’ s Manual.
2 iRobot Mirra 500 Series Owner’ s Manual IMPORT ANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL THE INSTRUCTIONS CAUTION: Do not plug the power supply into a grounded outlet or do not switch the pool cleaner “ON” if it is not fully immersed in water .
global.irobot.com 3 1) Handle 2) Cable 3) Outlet T op 4) Filter Access 5) Filter Lock Lever 6) Wheels 7) Unit Body 8) Intake Valves 9) Rolling Brush Dear Mirra Owner , Thank you for choosing a new generation iRobot Mirra pool cleaning robot. Y ou’r e joining a very special community of people - 7.
4 iRobot Mirra 500 Series Owner’ s Manual T able of Contents Getting Started ................................................................ 5 Maintenance and Adjustment ......................................... 6-7 Cleaning the Filter/ Changing the Rolling Brush .
global.irobot.com 5 1 2 4 3 56 7 Getting Started 12 cm (4.7 inch) 3.6m/11.8ft 15min. Soak wheels for 15 minutes.
6 iRobot Mirra 500 Series Owner’ s Manual Maintenance and Adjustment A B C D 15min. ST ART INT AKE V AL VES ADJUSTMENT Adjust filter valve to get best suction on ground. Adjust filter valve to get best clearance on ground. PV A WHEELS SOAKING Soak wheels after extended period of storage.
global.irobot.com 7 Maintenance and Adjustment Continued A1 A2 A3 A4 B2 B3 B1 B4 FLO A T INST ALLA TION Robot should turn 90 degrees on the first turn of a new cleaning cycle. Remove filter canister to access float block holder Adjust amount of float blocks to achieve desired turning behaviors.
8 iRobot Mirra 500 Series Owner’ s Manual Cleaning the Filter Changing the Rolling Brush It is recommended to clean the filter after each working-c ycle.
global.irobot.com 9 Accessing and Cleaning the Pr opeller DISCONNECT THE ROBO T FROM THE POWER-SUPPL Y BEFORE PERFORMING THIS ACTION 2 7 Propeller Clean here 6 1 5 10 9 4 3 8 Pump motor Clean the propeller if experiencing poor suction.
10 iRobot Mirra 500 Series Owner’ s Manual 4 1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and atleast 12 cm / 4 Inch above the surface. The transformer will supply low voltage to the cleaner . 2. Uncoil the cable.
global.irobot.com 11 Operating Y our Pool Cleaner - Plugging the Cable cable plug power supply socket cable plug power supply socket slot key slot key Push and rotate right to lock Rotate left and pull to unlock Cable plug (A) Socket (B) Plug T ype T o plug the cable (Fig A) into the socket on the power supply (Fig.
12 iRobot Mirra 500 Series Owner’ s Manual a. Power LED The blue LED flashes when the power supply is in standby mode and lights continuously when the pool cleaner is operating. b. “CLEAN” button The button switches between “ON” and “ST ANDBY”.
global.irobot.com 13 T roubleshooting Guide PLEASE CHECK THE FOLLOWING BEFORE CALLING YOUR SERVICE CENTER Before troubleshooting, the pool cleaner must be disconnected from the power supply and the power supply must be unplugged from the electrical outlet to prevent damage to the unit and possible personal injury.
14 iRobot Mirra 500 Series Owner’ s Manual Grounding The power supply must be connected to a grounded 3 conductor socket. The main power supply must be connected via a GFCI (ground fault circuit interrupter) or RCD (residual current device) having a rated residual opera ting current not greater than 30mA.
global.irobot.com 15 T roubleshooting Guide Declaration of Conformity T est Standards EN60335-1 Household and similar electrical appliances-Safety Part 1: General requirements EN60335-2-41 Household a.
© 2008-2013 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730 USA | All rights r eserved. iRobot is a registered trademark of iRobot Corporation. Mirra is a trademark of iRobot Corporation.
デバイスiRobot 530の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
iRobot 530をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはiRobot 530の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。iRobot 530の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。iRobot 530で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
iRobot 530を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はiRobot 530の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、iRobot 530に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちiRobot 530デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。