JacuzziメーカーJ-ALLURELuxury Bathing and Entertainment Systemの使用説明書/サービス説明書
ページ先へ移動 of 32
J-ALLURE ™ Installation & Operation Instructions WHIRLPOOL B ATH R Luxury Bathing and Entertainment System.
IMPORT ANT SAFETY INFORMA TION READ ALL INSTRUCTIONS BEFORE BEGINNING ASSEMBL Y AND INST ALLA TION. SUMMARY OF PRECAUTIONS • Suction cover must be in place at all times to minimize the potential for hair and body entrapment. • Keep body and hair a minimum of 6" away from suction fitting at all times when the whirlpool system is operating.
Contents 1 Important: Read complete instructions before beginning installation. Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for whirlpool operation. The drain/overflow kit and faucet kit must be installed on the bath by the installer.
J-Allure PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 2 9-1/8" 92-1/2" 72-7/16" 83-3/8" 20-1/4" 51-3/16" 51-3/16" 72-7/16" 13-3/4" 54".
J-Allure SCREW , M3.5X9.5, Quantity 4 SCREW , M3.9X22, Quantity 8 SCREW , M3.5X50, Quantity 4 SET SCREW , M5X9.9, Quantity 4 ACORN NUT , M5, Quantity 4 FLA T W ASHER, Quantity 2 EXTERNAL TO OTH LOCK-W.
J-Allure 4 Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of approximately 94 lb/sq. ft .
J-Allure Rough-in Reference 5 Rough-in The installation requires three cutouts in the walls. Two cutouts allow room for the speakers. The third cutout is necessary to route water supply piping to the center panel, and to route hoses for the steam generators to the bath.
J-Allure SHIM W ALL EXTRUSION FINISHED W ALL 90 ° SHIM W ALL EXTRUSION FINISHED W ALL 90 ° SHIM Finished W alls Before fixing the bath in place, make sure the finished walls above the rim of the bath are perpendicular. The two wall extrusions at the edges of the fixed panels will allow some compensation for walls out of true less than 3/16".
J-Allure 7 Wall Cutouts Suggested Rough-in Plumbing for Center Panel 2-3/4" 19-3/4" FINISHED FLOOR STUD 41-1/2" 1/2" NPTF 3/8 OD COPPER TUBE TO STEAMPRO UNITS COLD W A TER SUPPL Y HOT W A TER SUPPL Y STUD DET AIL 1 3-1/2" 38" 9" MIN.
J-Allure Skirt Installation It is necessary to mount the skirt shell clips on the factory installed wood blocks located along the underside of the rim. Mark hole locations on the blocks using clips as a template for correct hole spacing. Then drill a pilot hole 1/2" deep using a 3/32" diameter drill.
J-Allure Service Access The skirt fits along the front of the bath and is an access panel for servicing. Allow a space of at least 8 inches away from the bath for skirt removal. To remove the skirt, remove the screws at the bottom of the skirt and withdraw the skirt.
J-Allure W ater Supply Consult local authorities for plumbing code requirements in your area. IMPORTANT: Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the installer.
J-Allure Center Panel Installation Connect the fixed male end of the flexible supply lines to the female supply connections in the wall cutout. Position the center panel frame in the corner of the bath with the mounting tabs between the edge of the bath and wall.
J-Allure Center Panel Installation (cont.) Connect the ends of the flexible supply lines with adaptors to the hot and cold connections of the mixer. The steam lines are to be routed in such a way that they travel up from the steam generators and down to the steam heads.
J-Allure TV Installation (Units with TV) Remove drip shield. Connect power cord, audio cable antenna/cable TV. Hook up fan power lines with red to red and black to black wires. Tighten cable tie and cut off excess. Tighten cable tie with anchor (not supplied) to the TV power cord.
J-Allure Fixed Panels Installation Locate the guide with the gasket. This is the lower guide. Remove this gasket and install on the top guide. Position the lower guide on the two fixed panels while they are resting on the floor in an upside down position.
J-Allure 15 Fixed Panels Installation (cont.) Install the two wall extrusions on the ends of the fixed panel assembly. Make sure they are flush against each fixed panel. Where the fixed panel assembly will rest on the bath rim, apply sealant. Position the fixed panel assembly on the bath by inserting the pin into its seat on the lower guide.
J-Allure 16 Side W alls Installation Lift one of the side walls through the open doors. Reach under the bath rim and pull up the speaker wires. Hook up these wires observing the polarity as directed from the CD player manual. Then insert the 3 bolts into the slotted holes in the center panel frame.
J-Allure TWO STRIPS OF FOAM T APE SIDE BY SIDE FROM TOP TO BOTT OM (ONL Y ON RIGHT SIDE W ALL) SIDE W ALL W ALL EXTRUSION FIXED P ANEL FRAME SEALANT SIDE W ALL BA TH RIM SEALANT ALONG ENTIRE LENGTH OF.
J-Allure SEALANT FIXED P ANELS LOWER GUIDE Inside Caulking Caulk the joint between the lower guide and the bath. 18.
J-Allure 19 Sliding Doors Installation Take one of the doors inside the shower compartment. The upper rollers will be fixed while the bottom rollers will be loose. In a vertical position, insert the upper and lower rollers (at the same time) into the roller insertion point located at the center of the upper and lower guide.
J-Allure Dome Installation Apply gasket to dome as shown below. Note: there is no gasket on the dome where it rests on the upper guide. Then carefully lift the dome and place onto the corner panel , side walls and upper guide. Bring the edge of the dome in contact with the front part of the upper guide.
FIGURE 1. CENTER PANEL AND DISPLAY OPERA TING INSTRUCTIONS CENTER P ANEL System control is provided by the electronic display located on the center panel. The display is used to start up the five functions of the unit: the hand held shower, the fixed shower, the hydromassage (all jets), hydromassage (pulsed jets), and the steam bath.
Starting the Hydromassage The J-Allure allows you to enjoy the benefits of a real hydromassage. The hydromassage is created by the combined action of 8 water jets (two sets of four). The action of each group of four jets is either alternated or pulsed.
Controlling Whirlpool Action The whirlpool action in your bath is influenced by three factors – direction of flow, force of water, and force of air. All baths manufactured by Jacuzzi Whirlpool Bath are equipped with fully adjustable PowerPro ® jets, which are adjustable for all three factors.
BA TH MAINTENANCE Cleaning the Bath To clean your bath, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes.
25 Suction Cover/Strainer Maintenance Clean the suction cover/strainer of hair and debris when necessary. To do this, remove the center screw and detach the square cover. Clean the cover by backflush- ing debris from the holes. Replace the suction cover immediately after cleaning.
CARE AND MAINTENANCE OF STEAMPRO STEAM GENERA TORS Maintenance of the Steampros includes flushing periodically and visually inspecting for water leaks. To drain the units: 1. Turn OFF power to the unit. 2. To gain access to the SteamPro units, open the center panel door.
Printed in the U.S.A. Printed on Recycled Paper PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. ©1998 Jacuzzi Whirlpool Bath N115000C 12/02 Jacuzzi Whirlpool Bath National Headquarters P.
.
Jacuzzi Whirlpool Bath P .O. Drawer J W alnut Creek, CA 94596-9885 Jacuzzi Whirlpool Bath Limited W arranty Shower System Pr oduct WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers t.
N115000C WHIRLPOOL BATH R RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage.
デバイスJacuzzi J-ALLURELuxury Bathing and Entertainment Systemの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jacuzzi J-ALLURELuxury Bathing and Entertainment Systemをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJacuzzi J-ALLURELuxury Bathing and Entertainment Systemの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jacuzzi J-ALLURELuxury Bathing and Entertainment Systemの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jacuzzi J-ALLURELuxury Bathing and Entertainment Systemで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jacuzzi J-ALLURELuxury Bathing and Entertainment Systemを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJacuzzi J-ALLURELuxury Bathing and Entertainment Systemの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jacuzzi J-ALLURELuxury Bathing and Entertainment Systemに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJacuzzi J-ALLURELuxury Bathing and Entertainment Systemデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
