JacuzziメーカーS198の使用説明書/サービス説明書
ページ先へ移動 of 20
Affinity ™ Owner's Manual.
Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satis- faction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products.
Contents Specifications & Rough-in Reference _____________________________________________________ 2 Framing and Support _________________________________________________________________ 3 Wall Cu.
Specifications & Rough-in Reference DIMENSIONS 68" (1727 mm) L 68" (1727 mm) W 22" ( 559 mm) H1 27" ( 686 mm) H2 35-7/8" ( 911 mm) H3 DRAIN/OVERFLOW DIMENSIONS 19" (483 mm) A 12" (305 mm) B TOTAL WEIGHT/FLOOR LOADING 1500 lb (682 kg)/ 47 lb/sq.
Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor . The floor structure beneath the bath must be able to support a total weight of bath, water , and bather . Refer to the table under total weight for your model.
W all Cutout and CD/Radio Installation The installation requires a cutout in the wall. The cutout allows room for the speakers, CD/Radio speaker/power & TV audio cable wires. NOTE: CD/Radio must be must be located a minimum of 5' away from the interior of the bath.
Remove trim plate. Remove sleeve after disengaging sleeve locks. Stand the unit and insert the 2 handles between the unit and sleeve to disengage the sleeve locks. When standing the unit be careful not to damage the fuse on the rear. Remove the sleeve.
TV Installation Remove back cover by lifting straight upward and then remove the drip shield. Tighten cable tie and cut off excess. Tighten cable tie with anchor (not supplied) to the TV power cord. It is not necessary to attach anchor to drip shield; the cable tie and anchor are used to ensure the TV power cord remains in the TV housing.
Service Access For partially or fully sunken installations, allow for ac- cess to service connections. It is the installer's respon- sibility to provide sufficient service access. See Ser- vice Access illustration. Provide adequate ventilation (minimum 30 square inch opening) for cooling the mo- tor and to supply sufficient air for the jets.
Drain Information A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for dam- age and verify that the kit is of the proper finish.
9 Remote Control LED INDICA TOR BA TH MODE CHANNEL UP & DOWN JETS FUNCTION LIGHT FUNCTION TV MODE VOLUME UP & DOWN CD/DVD FUNCTION BLOWER FUNCTION POWER The Floating Remote Control is a universal remote control that has been programmed to operate the TV .
PURGES Automatic Purge With all functions off either , manually or by program, a 60 minute timer will be initiated. Once this timer is fin- ished, a 1 minute purge will be activated (blower) to purge any remaining water in the air channel. If any key is pressed the purge timer will be reset.
Controlling Whirlpool Action The whirlpool action in your bath is influenced by three factors – direction of flow , force of water , and force of air . Direction: To change the direction of the water flow , swivel the jet nozzle to the desired angle.
BA TH MAINTENANCE Cleaning the Bath To clean your bath, simply use a mild, nonabrasive liq- uid detergent solution. Y ou can protect and restore the gloss to a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes.
Lamp When the bulb burns out, replace it from the back of the lamp fitting, on the underside of the shell, by pulling out the bulb receptacle. Replacement bulbs (7W , 12V) are available from your Jacuzzi Whirlpool Bath dealer . LIGHT BULB LIGHT BEZEL SHELL BULB RECEPT ACLE LOCKING NUT LIGHT BULB REPLACEMENT Printed in the U.
14.
53 mm 182 mm TEMPLA TE FOR CD/RADIO MOUNTING SLEEVE 15.
.
WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”).
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.
デバイスJacuzzi S198の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Jacuzzi S198をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJacuzzi S198の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jacuzzi S198の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jacuzzi S198で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jacuzzi S198を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJacuzzi S198の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jacuzzi S198に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJacuzzi S198デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。